Paradyne 9820-2M, and 9820-45M, 9820-8M, 9623, 9788, 9128 standalone, 9720, 9783, 9123 manual Takes place

Page 31

2. Basic Configuration

Discovery Mode

Configuration Description

 

 

NetOnly

Auto-configuration of a network DLCI only; no Port-1 or

 

PVC connections are configured.

 

No Port-1, PVC connection, or management DLCI is

 

configured.

 

 

Disable

￿No frame relay discovery or automatic configuration

 

takes place.

 

The FrameSaver unit will be configured manually.

 

 

NOTE:

If the default setting (1MPort or 1PPort) is not the setting required for your application, change the Frame Relay Discovery Mode before connecting the network cable or editing discovered option settings. Otherwise, the FrameSaver unit will start discovering DLCIs as soon as it powers up.

If this occurs, you can recover by deleting the discovered DLCIs. If only a local management PVC between the router and the FrameSaver unit has been configured, simply select the desired Frame Relay Discovery Mode and Save the change.

The default discovery mode, depending on model, is 1MPort or 1PPort.

When 1MPort mode is active, the unit creates for each DLCI discovered on the network a multiplexed network interface DLCI (which contains two EDLCIs: one for Port-1 data and the other for management), a standard Port-1 DLCI (with the same number as the network interface DLCI), and a Management PVC, then cross-connects them. When LMI is active on the network interface and PVC status information (with provisioned DLCI numbers) is next received from the network, the unit automatically saves the settings to the Current Configuration area.

When 1PPort mode is active, the unit uses the Network DLCI values obtained from the Network LMI status response message to automatically configure for each DLCI a corresponding DLCI for Port 1 having the same numeric value as the Network DLCI, and automatically cross connects them. The DLCIs created on the network side are IP Enabled (not standard or multiplexed) DLCIs. In addition, payload management is configured for the network DLCI and assigned the Node IP Address.

Configuration options set by selecting a discovery mode can be manually modified, refined, or deleted at any time using the Configuration menus. No previously discovered and configured DLCIs or cross-connections will be removed unless authorized or Automatic Circuit Removal is enabled (see Automatically Removing a Circuit on page 2-16). Additional discovered DLCIs will be configured according to the current Frame Relay Discovery Mode setting. Selecting or changing the setting will not affect IP Addresses or Subnet Masks.

NOTE:

When auto-configuration creates a multiplexed DLCI, but a standard DLCI is needed, change the DLCI to standard from the network DLCI Records screen: Configuration→Network→DLCI Records

9000-A2-GB31-00

December 2002

2-15

Page 30 Page 32
Image 31
Page 30 Page 32
Contents FrameSaver SLV Copyright 2002 Paradyne Corporation All rights reserved Contents Contents Index Feature-Specific ConfigurationContents December Document Organization Purpose and Intended AudienceSection Description Other FrameSaver model-specific documentation includes Product-Related DocumentsDocument Number Document Title FrameSaver SLV reference library containsVii Conventions Used Convention Used When UsedConfiguration Procedures Configuration Menu Example Configuration MenuConfiguration Option Area Description Configuration Option AreasMain Menu→ Configuration Accessing and Displaying Configuration OptionsConfiguration→PVC Connections Changing Configuration OptionsSaving Configuration Options Basic Configuration Main Menu→ Easy Install Using the Easy Install FeatureEasy Install Screen Example DDS Interface Service Type Possible Settings Frame Relay, Leased Line, PPP Easy Install Configuration Options 1Dslam Easy Install Configuration Options 2Time Slot Assignment Screen 9123, 9126 Easy Install Configuration Options 3Create a Dedicated Network Management Link Ethernet Management Options ScreenNetwork 1 Line Build Out 9520, 9520-ILM Easy Install Configuration Options 4Network 1 Line Framing Format 9123, 9126 Network 1 Line Coding Format 9123, 9126Network 1 Port Type 9820-2M, 9820-8M Easy Install Configuration Options 5Network 1 DSL Line Rate Mode 9720, 9783 DS0 Base Rate 9123, 9126784 Easy Install Configuration Options 6Network 1 DSL Line Rate 384Network 1 Channel Easy Install Configuration Options 7Configuration→Data Ports→DLCI Records Using RIP with FrameSaver SLV CSU/DSUsMain Menu→ Control→System Information Entering System Information and Setting the System ClockIf the selection is Enter Main Menu→ Auto-Configuration Setting Up Auto-ConfigurationMain Menu→ Auto-Configuration→Frame Relay Discovery Mode Selecting a Frame Relay Discovery ModeDiscovery Mode Configuration Description Takes place Automatically Removing a Circuit Configuration Option Tables Configuration OptionsConfiguration Options System Frame Relay and LMI Options 1 Configuring the Overall SystemConfiguring Frame Relay and LMI for the System CSU/DSUs Main Menu→ Configuration→System →Frame Relay and LMISystem Frame Relay and LMI Options 2 System Frame Relay and LMI Options 3 LMI Heartbeat T1 Possible Settings 5, 10, 15, 20, 25 LMI Status Enquiry N1 Possible Settings 1, 2, 3, 4System Frame Relay and LMI Options 4 PPP Options Configuring PPP OptionsMain Menu→ Configuration→System→PPP Possible Settings Independent, Port-1FollowsNetField Setting After RfcCodePoints Selected Configuring Class of Service DefinitionsCode Points Assigned Class of Service DefinitionsClass of Svc Name Measure Latency & AvailabilityName Code Point DefinitionsCode Point Definitions Code PntSLV Type Available Settings Standard, COS 1-COS Configuring Service Level Verification OptionsMain Menu→ Configuration→System→Service Level Verification Service Level Verification Options 1SLV Timeout Clearing Event Threshold Service Level Verification Options 2Dlci Down on SLV Timeout SLV Timeout Error Event ThresholdSLV Latency Clearing Event Threshold Service Level Verification Options 3SLV Packet Size bytes General System Options 1 Configuring General System OptionsMain Menu→ Configuration→System→General Test TimeoutGeneral System Options 2 General System Options 3 System Alarm RelayConfiguring the Network Interface Configuring Physical InterfacesMain Menu→ Configuration→Network→Physical T1 Network Physical Interface Options 1 T1 Network InterfaceNetwork Initiated PLB T1 Network Physical Interface Options 2Transmit Timing Network Initiated LLBESF Network Initiated Dclb Possible Settings Disable, V.54&ANSIT1 Network Physical Interface Options 3 Ansi Performance Report MessagesCircuit Identifier T1 Network Physical Interface Options 4T3 Network Physical Interface Options T3 Network InterfaceLine Build Out DDS Network Physical Interface Options 1 DDS Network InterfaceDSU Latching Loopback DDS Network Physical Interface Options 2Require DSU Latching Loopback Preamble Channel Operating Rate Possible Settings AutoRate, 64, 128Idsl Network Interface 10. Idsl Network Physical Interface OptionsDSL Line Rate Kbps Line Rate Mode Possible Settings Hunt, AutoRate, FixedSdsl Network Interface 11. Sdsl Network Physical Interface Options12. Shdsl Network Physical Interface Options 1 Shdsl Network InterfacePort Type Synchronous Network Interface12. Shdsl Network Physical Interface Options 2 PSD MaskMonitor CTS Monitor DSRMonitor Rlsd 14. Hssi Network Data Port Physical Interface Options Hssi Network Interface15. V.35 Data Port Physical Interface Options 1 Configuring a User Data Port CSU/DSUsMain Menu→ Configuration→Data Ports→Physical Data Port Physical InterfacePort Base Rate Port Use Possible Settings Frame Relay, Synchronous Data15. V.35 Data Port Physical Interface Options 2 Max Port RateTransmit Clock Source 15. V.35 Data Port Physical Interface Options 3Monitor RTS Monitor DTR 15. V.35 Data Port Physical Interface Options 4Port DTE Initiated Loopbacks 15. V.35 Data Port Physical Interface Options 5 Action on Network Yellow AlarmInvert Transmit and Receive Data 15. V.35 Data Port Physical Interface Options 6 EIA-530-A/X.21/V.35 Data Port Physical InterfaceTransmit Clock Source 17. Hssi Data Port Physical Interface Options 1 Hssi Data Port Physical Interface17. Hssi Data Port Physical Interface Options 2 17. Hssi Data Port Physical Interface Options 3 Main Menu→ Configuration→T3 User Ports→ Physical Configuring the T3 User Port 9520-ILM18. T3 User Port Physical Interface Options Interface Status Configuring the DSX-1 Interface 9126Main Menu→ Configuration→DSX-1 19. DSX-1 Physical Interface Options 1Send All Ones on DSX-1 Failure 19. DSX-1 Physical Interface Options 220. Isdn BRI DBM Physical Interface Options 9126 Configuring the Isdn DBM Interface 9126, 9128Main Menu→ Configuration→ISDN→Physical Service Profile ID Spid 1 or21. Isdn PRI DBM Physical Interface Options 9128 1 Switch Type Possible Settings NI-2, ATT4ESS, ATT5ESSLocal Phone Number 21. Isdn PRI DBM Physical Interface Options 9128 2 Line Build Out LBO Possible Settings 0.0, -7.5, -1521. Isdn PRI DBM Physical Interface Options 9128 3 Link Name Setting Up Isdn Link Profiles 9126, 9128Main Menu→ Configuration→ISDN→ISDN Link Profiles 22. Isdn Link Profile Options 1Maximum Link Rate Kbps 22. Isdn Link Profile Options 2Outbound Phone Number Inbound Calling ID 1 orAlternate Outbound Phone Number Assigning Time Slots/Cross Connections22. Isdn Link Profile Options 3 Caller Identification MethodValue Meaning Assigning Time Slots to the Network InterfacePPP Assigning DSX-1 Time Slots to the Network Interface DSX-1 to Network Time Slot Assignment Screen Example DSX-1 Signaling Assignments and Trunk Conditioning RBS Idle PLAR3idle Synchronous Data Port Assignment Screen Example Clearing Assignments 24. Interface Frame Relay Options 1 Configuring Frame Relay for an InterfaceLMI Frame Relay DS0s Base Rate 24. Interface Frame Relay Options 2Traffic Policing LMI Parameters24. Interface Frame Relay Options 3 Main Menu→ Configuration→Network/Data Ports → PPP Configuring PPP for an Interface25. Interface PPP Options 26. Dlci Record Options 1 Manually Configuring Dlci RecordsDlci Number CIR bps 26. Dlci Record Options 2Committed Burst Size Bc Bits 26. Dlci Record Options 3Excess Burst Size Bits Outbound Management Priority Backup Group Possible Settings A, B, C, . . . Z, None26. Dlci Record Options 4 Dlci PriorityVPI,VCI Number Configuring Circuit Records for the Network InterfaceMain Menu →Configuration →Network →Circuit Records 27. Circuit Records Options 19783 0 9788 0 27. Circuit Records Options 2Excess Burst Size Be Bits 27. Circuit Records Options 39783 9788 28. Network ATM Options Configuring ATM for the Network InterfaceMain Menu→ Configuration→Network →ATM Cell Delineation Error Event ThresholdSource Dlci Configuring PVC ConnectionsMain Menu→ Configuration→PVC Connections 29. PVC Connection Options 1Primary Destination Dlci 29. PVC Connection Options 2Source Edlci Primary Destination LinkAlternate Destination Dlci 29. PVC Connection Options 3Primary Destination Edlci Alternate Destination LinkAlternate Destination Edlci 29. PVC Connection Options 4Main Menu→ Configuration→IP Path List Static Configuring the IP Path List30. IP Path List Setting Up Management and Communication Options 31. Node IP Options 1 Configuring Node IP Information31. Node IP Options 2 31. Node IP Options 3 TS Access Management LinkManagement MTU Size TS Management Snmp Validation 31. Node IP Options 432. Management PVC Options 1 Configuring Management PVCsPayload Managed 32. Management PVC Options 2Set DE Primary Dlci 32. Management PVC Options 3Primary Edlci 32. Management PVC Options 4Alternate Dlci 32. Management PVC Options 5Alternate Edlci Encapsulation 32. Management PVC Options 6Snmp Management Configuring General Snmp ManagementName 1 Access 33. General Snmp Management Options 1Name 2 Access Configuring Telnet and/or FTP Session Support33. General Snmp Management Options 2 34. Telnet and FTP Session Options 1 Telnet Login RequiredTelnet Session 34. Telnet and FTP Session Options 2 Number of Managers Configuring Snmp NMS Security35. Snmp NMS Security Options 1 NMS IP Validation35. Snmp NMS Security Options 2 Configuring Snmp Traps and Trap Dial-Out36. Snmp Traps and Trap Dial-Out Options 1 Link see -38, Communication Port Options 36. Snmp Traps and Trap Dial-Out Options 236. Snmp Traps and Trap Dial-Out Options 3 Link Traps Possible Settings Disable, Up, Down, BothEnterprise Specific Traps Rmon Traps Possible Settings Network, Ports, DBM, All, None36. Snmp Traps and Trap Dial-Out Options 4 Dlci Traps on Interfaces Filter Selection FieldTrap Disconnect Dial-Out Delay TIme Min36. Snmp Traps and Trap Dial-Out Options 5 Trap Dial-OutIP SLV Availability Traps 36. Snmp Traps and Trap Dial-Out Options 6Alternate Dial-Out Directory Latency Traps37. Ethernet Management Options 1 Configuring Ethernet ManagementProxy ARP 37. Ethernet Management Options 238. Communication Port Options 1 Configuring the Communication PortCharacter Length Stop Bits Login Required38. Communication Port Options 2 Parity38. Communication Port Options 3 103RIP 38. Communication Port Options 438. Communication Port Options 5 Configuring the Modem Port39. Modem Port Options 1 39. Modem Port Options 2 10639. Modem Port Options 3 10739. Modem Port Options 4 Main Menu→ Configuration→Auto Backup Criteria Configuring the Criteria for Automatic Backup40. Auto Backup Criteria Options 1 Backup Allowed Day To nnnn 40. Auto Backup Criteria Options 2When Auto Backup Allowed Backup Allowed Day From nnnnFeature-Specific Configuration AT Command String To configure the modem to Setting Up an External ModemValid characters include For Setting Up an Internal ModemSetting Up Call Directories for Trap Dial-Out Main Menu→Control→Modem Call DirectoriesSetting Up to Use the Modem PassThru Feature Setting Up the DBM Physical Interface Setting Up Dial BackupMain Menu→Configuration→ISDN→Physical If you select Then Setting Up Automatic Backup ConfigurationConnections? PVC Connections? Following prompt When Appears If you selectCriteria for Automatic Backup in , Configuration Options For Originating a Backup Call For Answering a Backup Call Main Menu→Configuration→ISDN→Link ProfilesModifying Isdn Link Profiles Main Menu→Configuration→Auto-Backup Criteria Restricting Automatic Backup and Configuring Backup TimersAssigning DLCIs to a Backup Group Configuring the DBM Interface to Send Snmp TrapsMain Menu→Control→Change Operating Mode PVC Backup Over the Network InterfaceSetting Up Back-to-Back Operation Changing Operating ModeFeature-Specific Configuration 9000-A2-GB31-00 December Feature-Specific Configuration December ATM ARPRTS DBMDTR RlsdIdsl DTEEIR DSLIsdn IP SLVHssi IN-5 NMS IN-6SLV Snmp NMSIP Slip PVCIN-8 IN-9 IN-10
Related manuals
Manual 271 pages 14.3 Kb Manual 278 pages 35.32 Kb Manual 28 pages 41.96 Kb Manual 233 pages 22.17 Kb Manual 340 pages 17.41 Kb

and 9820-45M, 9123, 9623, 9783, 9720 specifications

The Paradyne 9820-8M, 9788, 9128 standalone, 9128 carrier-mount, and 9820-2M are critical components in telecommunications networks, designed to enhance data transmission and improve connectivity. Each model offers unique features and capabilities that cater to various requirements in both enterprise and service provider environments.

The Paradyne 9820-8M is a multi-service access platform that provides high-speed connectivity for voice, video, and data transmission. It supports multiple protocols, enabling seamless integration into existing infrastructures. Key features include a modular design that allows for scalability and easy upgrades, ensuring that organizations can adapt to evolving demands. Its advanced error correction and QoS (Quality of Service) features ensure reliable performance, even in challenging network conditions.

The Paradyne 9788 serves as a versatile platform for both digital and analog communications. It excels in the delivery of broadband services, supporting T1/E1 lines and providing robust mechanisms for data transmission. This model emphasizes redundancy and resilience, with built-in protection switching capabilities that maintain service continuity during faults or maintenance activities. Its compact design makes it an ideal solution for environments with space constraints.

The 9128 standalone model is aimed at customers requiring an easy-to-deploy solution for point-to-point connections. This model offers critical features such as an intuitive user interface, comprehensive diagnostics, and monitoring capabilities that facilitate system management. It also supports diverse network topologies, making it suitable for various deployment scenarios.

In contrast, the 9128 carrier-mount version is engineered for organizations needing to manage multiple connections within a central office or remote site. This model is specifically designed to be mounted in standard telecom racks, optimizing space utilization while maintaining high performance. Its robust hardware allows for excellent thermal management and environmental resilience.

Lastly, the Paradyne 9820-2M combines versatility with high-performance capabilities, making it a reliable choice for service providers. It features dual-channel support, enabling simultaneous transmission and providing a cost-effective solution for high-capacity data needs. With enhanced security features, including encryption capabilities, the 9820-2M ensures that sensitive information transmitted across networks is protected against unauthorized access.

Collectively, these Paradyne models exemplify advanced telecommunications technology, offering scalability, resilience, and high performance. Their diverse features cater to the unique demands of various users, from enterprise networks to service providers, facilitating the continual evolution of communication technologies.
Top Page Image Contents