Paradyne 9820-8M, 9820-2M Telnet and FTP Session Options 1, Telnet Session, Telnet Login Required

Page 122

3. Configuration Options

Table 3-34. Telnet and FTP Session Options (1 of 2)

Telnet Session

Possible Settings: Enable, Disable

Default Setting: Enable

Specifies whether the FrameSaver unit will respond to a session request from a Telnet client on an interconnected IP network.

Enable – Allows Telnet sessions between the FrameSaver unit and Telnet client.

Disable – Does not allow Telnet sessions.

Telnet Login Required

Possible Settings: Enable, Disable

Default Setting: Disable

Specifies whether a user ID and password (referred to as the login) are required to access the menu-driven user interface via a Telnet session. If required, the login used is the same login used for an menu-driven user interface session. This option does not affect the TS Access Management Link.

Enable – Requires a login to access a Telnet session.

Disable – Does not require a login.

Session Access Level

Possible Settings: Level-1, Level-2, Level-3

Default Setting: Level-1

Specifies the highest security level allowed when accessing the menu-driven user interface via a Telnet session. If a login is required for the session, the effective access level is also determined by the user’s access level. When a login is not required, the effective access level is determined by this option. This option does not affect the TS Access Management Link.

NOTE: The effective access level is always the lowest one assigned to either the session or the user. For example, if the assigned Session Access Level is Level-2, but the User Access Level is Level-3, then only level-3 access is allowed for the session.

Level-1– Allows Telnet access by users with Login ID access levels of 1, 2, and 3, with the capability to view system information, change configuration options, and run tests. This is the highest access level allowed.

CAUTION: Before changing the session access level to Level-2 or 3, make sure that the COM port’s Port Access Level is set to Level-1 and that at least one Login ID is set to Level-1. Otherwise, access will be lost. If this occurs, you must reset the unit to the factory defaults and begin the configuration process again. A reset is required if the Communication Port’s Port Use option is set to Net Link (see Table 3-6, General System Options).

Level-2– Allows Telnet access by users with Login ID access levels of 1, 2, and 3, with the capability to view system information and run tests only; they cannot change configuration options.

Level-3– Allows Telnet access by users with Login ID access levels of 1, 2, and 3, with the capability to view system information only; they cannot change configuration options or run tests.

3-90

December 2002

9000-A2-GB31-00

Page 121 Page 123
Image 122
Page 121 Page 123
Contents FrameSaver SLV Copyright 2002 Paradyne Corporation All rights reserved Contents Contents Feature-Specific Configuration IndexContents December Section Description Purpose and Intended AudienceDocument Organization FrameSaver SLV reference library contains Product-Related DocumentsDocument Number Document Title Other FrameSaver model-specific documentation includesVii Convention Used When Used Conventions UsedConfiguration Procedures Configuration Menu Configuration Menu ExampleConfiguration Option Areas Configuration Option Area DescriptionAccessing and Displaying Configuration Options Main Menu→ ConfigurationChanging Configuration Options Configuration→PVC ConnectionsSaving Configuration Options Basic Configuration Using the Easy Install Feature Main Menu→ Easy InstallEasy Install Screen Example DDS Interface Easy Install Configuration Options 1 Service Type Possible Settings Frame Relay, Leased Line, PPPEasy Install Configuration Options 2 DslamEthernet Management Options Screen Easy Install Configuration Options 3Create a Dedicated Network Management Link Time Slot Assignment Screen 9123, 9126Network 1 Line Coding Format 9123, 9126 Easy Install Configuration Options 4Network 1 Line Framing Format 9123, 9126 Network 1 Line Build Out 9520, 9520-ILMDS0 Base Rate 9123, 9126 Easy Install Configuration Options 5Network 1 DSL Line Rate Mode 9720, 9783 Network 1 Port Type 9820-2M, 9820-8M384 Easy Install Configuration Options 6Network 1 DSL Line Rate 784Easy Install Configuration Options 7 Network 1 ChannelUsing RIP with FrameSaver SLV CSU/DSUs Configuration→Data Ports→DLCI RecordsIf the selection is Enter Entering System Information and Setting the System ClockMain Menu→ Control→System Information Setting Up Auto-Configuration Main Menu→ Auto-ConfigurationDiscovery Mode Configuration Description Selecting a Frame Relay Discovery ModeMain Menu→ Auto-Configuration→Frame Relay Discovery Mode Takes place Automatically Removing a Circuit Configuration Options Configuration Option TablesConfiguration Options Main Menu→ Configuration→System →Frame Relay and LMI Configuring the Overall SystemConfiguring Frame Relay and LMI for the System CSU/DSUs System Frame Relay and LMI Options 1System Frame Relay and LMI Options 2 System Frame Relay and LMI Options 3 System Frame Relay and LMI Options 4 LMI Status Enquiry N1 Possible Settings 1, 2, 3, 4LMI Heartbeat T1 Possible Settings 5, 10, 15, 20, 25 Possible Settings Independent, Port-1FollowsNet Configuring PPP OptionsMain Menu→ Configuration→System→PPP PPP OptionsConfiguring Class of Service Definitions Field Setting After RfcCodePoints SelectedMeasure Latency & Availability Class of Service DefinitionsClass of Svc Name Code Points AssignedCode Pnt Code Point DefinitionsCode Point Definitions NameService Level Verification Options 1 Configuring Service Level Verification OptionsMain Menu→ Configuration→System→Service Level Verification SLV Type Available Settings Standard, COS 1-COSSLV Timeout Error Event Threshold Service Level Verification Options 2Dlci Down on SLV Timeout SLV Timeout Clearing Event ThresholdSLV Packet Size bytes Service Level Verification Options 3SLV Latency Clearing Event Threshold Test Timeout Configuring General System OptionsMain Menu→ Configuration→System→General General System Options 1General System Options 2 System Alarm Relay General System Options 3Main Menu→ Configuration→Network→Physical Configuring Physical InterfacesConfiguring the Network Interface T1 Network Interface T1 Network Physical Interface Options 1Network Initiated LLB T1 Network Physical Interface Options 2Transmit Timing Network Initiated PLBAnsi Performance Report Messages Network Initiated Dclb Possible Settings Disable, V.54&ANSIT1 Network Physical Interface Options 3 ESFT1 Network Physical Interface Options 4 Circuit IdentifierLine Build Out T3 Network InterfaceT3 Network Physical Interface Options DDS Network Interface DDS Network Physical Interface Options 1Require DSU Latching Loopback Preamble DDS Network Physical Interface Options 2DSU Latching Loopback 10. Idsl Network Physical Interface Options Operating Rate Possible Settings AutoRate, 64, 128Idsl Network Interface Channel11. Sdsl Network Physical Interface Options Line Rate Mode Possible Settings Hunt, AutoRate, FixedSdsl Network Interface DSL Line Rate KbpsShdsl Network Interface 12. Shdsl Network Physical Interface Options 1PSD Mask Synchronous Network Interface12. Shdsl Network Physical Interface Options 2 Port TypeMonitor Rlsd Monitor DSRMonitor CTS Hssi Network Interface 14. Hssi Network Data Port Physical Interface OptionsData Port Physical Interface Configuring a User Data Port CSU/DSUsMain Menu→ Configuration→Data Ports→Physical 15. V.35 Data Port Physical Interface Options 1Max Port Rate Port Use Possible Settings Frame Relay, Synchronous Data15. V.35 Data Port Physical Interface Options 2 Port Base RateMonitor RTS 15. V.35 Data Port Physical Interface Options 3Transmit Clock Source Port DTE Initiated Loopbacks 15. V.35 Data Port Physical Interface Options 4Monitor DTR Invert Transmit and Receive Data Action on Network Yellow Alarm15. V.35 Data Port Physical Interface Options 5 EIA-530-A/X.21/V.35 Data Port Physical Interface 15. V.35 Data Port Physical Interface Options 6Transmit Clock Source Hssi Data Port Physical Interface 17. Hssi Data Port Physical Interface Options 117. Hssi Data Port Physical Interface Options 2 17. Hssi Data Port Physical Interface Options 3 18. T3 User Port Physical Interface Options Configuring the T3 User Port 9520-ILMMain Menu→ Configuration→T3 User Ports→ Physical 19. DSX-1 Physical Interface Options 1 Configuring the DSX-1 Interface 9126Main Menu→ Configuration→DSX-1 Interface Status19. DSX-1 Physical Interface Options 2 Send All Ones on DSX-1 FailureService Profile ID Spid 1 or Configuring the Isdn DBM Interface 9126, 9128Main Menu→ Configuration→ISDN→Physical 20. Isdn BRI DBM Physical Interface Options 9126Local Phone Number Switch Type Possible Settings NI-2, ATT4ESS, ATT5ESS21. Isdn PRI DBM Physical Interface Options 9128 1 Line Build Out LBO Possible Settings 0.0, -7.5, -15 21. Isdn PRI DBM Physical Interface Options 9128 221. Isdn PRI DBM Physical Interface Options 9128 3 22. Isdn Link Profile Options 1 Setting Up Isdn Link Profiles 9126, 9128Main Menu→ Configuration→ISDN→ISDN Link Profiles Link NameInbound Calling ID 1 or 22. Isdn Link Profile Options 2Outbound Phone Number Maximum Link Rate KbpsCaller Identification Method Assigning Time Slots/Cross Connections22. Isdn Link Profile Options 3 Alternate Outbound Phone NumberPPP Assigning Time Slots to the Network InterfaceValue Meaning Assigning DSX-1 Time Slots to the Network Interface DSX-1 to Network Time Slot Assignment Screen Example DSX-1 Signaling Assignments and Trunk Conditioning RBS Idle PLAR3idle Synchronous Data Port Assignment Screen Example Clearing Assignments LMI Configuring Frame Relay for an Interface24. Interface Frame Relay Options 1 LMI Parameters 24. Interface Frame Relay Options 2Traffic Policing Frame Relay DS0s Base Rate24. Interface Frame Relay Options 3 25. Interface PPP Options Configuring PPP for an InterfaceMain Menu→ Configuration→Network/Data Ports → PPP Dlci Number Manually Configuring Dlci Records26. Dlci Record Options 1 26. Dlci Record Options 2 CIR bpsExcess Burst Size Bits 26. Dlci Record Options 3Committed Burst Size Bc Bits Dlci Priority Backup Group Possible Settings A, B, C, . . . Z, None26. Dlci Record Options 4 Outbound Management Priority27. Circuit Records Options 1 Configuring Circuit Records for the Network InterfaceMain Menu →Configuration →Network →Circuit Records VPI,VCI Number27. Circuit Records Options 2 9783 0 9788 09783 9788 27. Circuit Records Options 3Excess Burst Size Be Bits Cell Delineation Error Event Threshold Configuring ATM for the Network InterfaceMain Menu→ Configuration→Network →ATM 28. Network ATM Options29. PVC Connection Options 1 Configuring PVC ConnectionsMain Menu→ Configuration→PVC Connections Source DlciPrimary Destination Link 29. PVC Connection Options 2Source Edlci Primary Destination DlciAlternate Destination Link 29. PVC Connection Options 3Primary Destination Edlci Alternate Destination Dlci29. PVC Connection Options 4 Alternate Destination Edlci30. IP Path List Configuring the IP Path ListMain Menu→ Configuration→IP Path List Static Setting Up Management and Communication Options Configuring Node IP Information 31. Node IP Options 131. Node IP Options 2 Management MTU Size TS Access Management Link31. Node IP Options 3 31. Node IP Options 4 TS Management Snmp ValidationConfiguring Management PVCs 32. Management PVC Options 1Set DE 32. Management PVC Options 2Payload Managed 32. Management PVC Options 3 Primary Dlci32. Management PVC Options 4 Primary EdlciAlternate Edlci 32. Management PVC Options 5Alternate Dlci 32. Management PVC Options 6 Encapsulation33. General Snmp Management Options 1 Configuring General Snmp ManagementName 1 Access Snmp Management33. General Snmp Management Options 2 Configuring Telnet and/or FTP Session SupportName 2 Access Telnet Session Telnet Login Required34. Telnet and FTP Session Options 1 34. Telnet and FTP Session Options 2 NMS IP Validation Configuring Snmp NMS Security35. Snmp NMS Security Options 1 Number of Managers36. Snmp Traps and Trap Dial-Out Options 1 Configuring Snmp Traps and Trap Dial-Out35. Snmp NMS Security Options 2 36. Snmp Traps and Trap Dial-Out Options 2 Link see -38, Communication Port OptionsEnterprise Specific Traps Link Traps Possible Settings Disable, Up, Down, Both36. Snmp Traps and Trap Dial-Out Options 3 Dlci Traps on Interfaces Filter Selection Field Possible Settings Network, Ports, DBM, All, None36. Snmp Traps and Trap Dial-Out Options 4 Rmon TrapsTrap Dial-Out Dial-Out Delay TIme Min36. Snmp Traps and Trap Dial-Out Options 5 Trap DisconnectLatency Traps 36. Snmp Traps and Trap Dial-Out Options 6Alternate Dial-Out Directory IP SLV Availability TrapsConfiguring Ethernet Management 37. Ethernet Management Options 137. Ethernet Management Options 2 Proxy ARPCharacter Length Configuring the Communication Port38. Communication Port Options 1 Parity Login Required38. Communication Port Options 2 Stop Bits103 38. Communication Port Options 338. Communication Port Options 4 RIP39. Modem Port Options 1 Configuring the Modem Port38. Communication Port Options 5 106 39. Modem Port Options 2107 39. Modem Port Options 339. Modem Port Options 4 40. Auto Backup Criteria Options 1 Configuring the Criteria for Automatic BackupMain Menu→ Configuration→Auto Backup Criteria Backup Allowed Day From nnnn 40. Auto Backup Criteria Options 2When Auto Backup Allowed Backup Allowed Day To nnnnFeature-Specific Configuration Setting Up an External Modem AT Command String To configure the modem toMain Menu→Control→Modem Call Directories Setting Up an Internal ModemSetting Up Call Directories for Trap Dial-Out Valid characters include ForSetting Up to Use the Modem PassThru Feature Main Menu→Configuration→ISDN→Physical Setting Up Dial BackupSetting Up the DBM Physical Interface Setting Up Automatic Backup Configuration If you select ThenFollowing prompt When Appears If you select Connections? PVC Connections?Criteria for Automatic Backup in , Configuration Options Modifying Isdn Link Profiles Main Menu→Configuration→ISDN→Link ProfilesFor Originating a Backup Call For Answering a Backup Call Restricting Automatic Backup and Configuring Backup Timers Main Menu→Configuration→Auto-Backup CriteriaConfiguring the DBM Interface to Send Snmp Traps Assigning DLCIs to a Backup GroupChanging Operating Mode PVC Backup Over the Network InterfaceSetting Up Back-to-Back Operation Main Menu→Control→Change Operating ModeFeature-Specific Configuration 9000-A2-GB31-00 December Feature-Specific Configuration December ARP ATMRlsd DBMDTR RTSDSL DTEEIR IdslHssi IP SLVIsdn IN-5 IN-6 NMSPVC Snmp NMSIP Slip SLVIN-8 IN-9 IN-10
Related manuals
Manual 271 pages 14.3 Kb Manual 278 pages 35.32 Kb Manual 28 pages 41.96 Kb Manual 233 pages 22.17 Kb Manual 340 pages 17.41 Kb

and 9820-45M, 9123, 9623, 9783, 9720 specifications

The Paradyne 9820-8M, 9788, 9128 standalone, 9128 carrier-mount, and 9820-2M are critical components in telecommunications networks, designed to enhance data transmission and improve connectivity. Each model offers unique features and capabilities that cater to various requirements in both enterprise and service provider environments.

The Paradyne 9820-8M is a multi-service access platform that provides high-speed connectivity for voice, video, and data transmission. It supports multiple protocols, enabling seamless integration into existing infrastructures. Key features include a modular design that allows for scalability and easy upgrades, ensuring that organizations can adapt to evolving demands. Its advanced error correction and QoS (Quality of Service) features ensure reliable performance, even in challenging network conditions.

The Paradyne 9788 serves as a versatile platform for both digital and analog communications. It excels in the delivery of broadband services, supporting T1/E1 lines and providing robust mechanisms for data transmission. This model emphasizes redundancy and resilience, with built-in protection switching capabilities that maintain service continuity during faults or maintenance activities. Its compact design makes it an ideal solution for environments with space constraints.

The 9128 standalone model is aimed at customers requiring an easy-to-deploy solution for point-to-point connections. This model offers critical features such as an intuitive user interface, comprehensive diagnostics, and monitoring capabilities that facilitate system management. It also supports diverse network topologies, making it suitable for various deployment scenarios.

In contrast, the 9128 carrier-mount version is engineered for organizations needing to manage multiple connections within a central office or remote site. This model is specifically designed to be mounted in standard telecom racks, optimizing space utilization while maintaining high performance. Its robust hardware allows for excellent thermal management and environmental resilience.

Lastly, the Paradyne 9820-2M combines versatility with high-performance capabilities, making it a reliable choice for service providers. It features dual-channel support, enabling simultaneous transmission and providing a cost-effective solution for high-capacity data needs. With enhanced security features, including encryption capabilities, the 9820-2M ensures that sensitive information transmitted across networks is protected against unauthorized access.

Collectively, these Paradyne models exemplify advanced telecommunications technology, offering scalability, resilience, and high performance. Their diverse features cater to the unique demands of various users, from enterprise networks to service providers, facilitating the continual evolution of communication technologies.
Top Page Image Contents