Setup Menu, Login Menu | Liebert Universal Monitor specification

Setup Menu

A.6 SETUP MENU

The Setup menu allows the user to configure the Universal Monitor—setting up inputs and outputs and an input/output matrix to trigger actions, the modem and pagers, and system features such as date and time. This menu also provides a vehicle for manually changing the state of an output to ON or OFF, clearing active alarms and deleting records from the Universal Monitor’s alarm log, event log and trend logs.

Main Menu

After connecting to the Service Terminal Interface, the Main Menu appears, as shown below.

Main Menu

LIEBERT UNIVERSAL MONITOR

VX.XXX.X

LIEBERT CORPORATION COPYRIGHT 2003

ALL RIGHTS RESERVED

MAIN MENU

1=VIEW ACTIVE ALARMS 2=VIEW ALARM LOG 3=VIEW EVENT LOG 4=VIEW TREND LOG

5=VIEW INPUT & SENSOR STATUS 6=VIEW OUTPUT STATUS 7=VIEW PAGER NUMBERS 8=SILENCE ALARM

9=BACKUP LOG FILES

0=SETUP SYSTEM-LOGIN REQUIRED

SELECT A NUMBER:0

• Choose 0 to access the features illustrated in this section.

Login Menu

The System and Control options require a password to prevent unauthorized users from making changes to the system. After choosing 0 in the Main Menu above, the Login Menu appears:

Login

YOU MUST LOGIN TO PERFORM

SETUP OR TO MAKE CHANGES

LOGIN WITH 4 CHARACTER

PASSWORD

>****

>INVALID PASSWORD, ENTER AGAIN >PRESS <ESC> TO EXIT

>

• Enter the password, and the Setup Menu appears, as shown in the following section.

104

Image 112

Liebert Universal Monitor user manual Setup Menu, Login Menu

Contents

Universal Monitor MonitoringPage Table of Contents Opening Screen Overview Main Menu Overview LCD Menu Overview Setup System Setup I/O Matrix Appendix a Service Terminal Interface Appendix B Default Settings Quick Reference Guide Figures Page Methods of Viewing and Configuring the Universal Monitor Optional FeaturesAvailable Alarms Data Logs Enclosure has knockouts Access slots Outside Enclosure OverviewOn top Transformer Module Back of LCD Controller Board Typical Configuration Universal Monitor Main board RS232 Phone LineDigital outputs Digital inputs Controller Board Overview Controller board components Of-power jumper Connector EIA422EIA485 connector Connector RS232 Optional Expansion Board Overview Expansion board components LED Indicators LED indicators summary LED Indicators Optional Expansion Board Color Description Power statusEIA485 status LEDs D4 yellow D5 red General status LED D3 green Typical Sequence Installation Considerations Installation Main BoardPacking Contents Unpacking and Preliminary Inspection Surface-Mounting the Universal Monitor Required toolsMounting the Panel Bottom hole diameter Flush-Mounting the Universal Monitor Connect Power to the Universal Monitor Input Power Connections Small Enclosure Input Power Connections VAC Output Power ConnectionsTermination and Mounting Large Enclosure Connection Type Troubleshooting Transformer Module Connecting the Battery PackObtaining a Replacement Battery Pack Problem Possible Solution Replacement Fuse Part Numbers Installation Optional Expansion Board Packing manifest optional Expansion Board Mounting Dimensions optional Expansion Board Surface-Mounting the Optional Expansion Board Flush-Mounting the Optional Expansion Board Input Power Connections Optional Expansion Board Pre-wired24VAC wiring red & white 24VAC input connectors AC1 & AC2 TM115 shown Wiring and Connections Main Board Wiring SpecificationsWiring specifications main board Connecting Digital Inputs and Digital Outputs Connecting Digital InputsConnecting Digital Outputs Proceeds up numbering keys are shown at right Setting the Digital Output Jumpers Connecting Analog InputsDigital output jumper settings Setting the 12VDC/24VDC Analog Power Jumper Connecting the Analog Ground Connecting Common Alarm Outputs EIA422 SiteScan Web Connector1 RS232 Connector Phone Line Connector Wiring and Connections Optional Expansion Board Wiring specifications optional Expansion Board Connecting Inputs and Outputs Numbering keys Numbering Relay is Closed On power failureKeys DIP switch setting outputs wired as Normally Closed N.C Setting the Digital Output DIP SwitchesDIP switch setting outputs wired as Normally Open N.O Enable the Connection via Firmware Connect EIA485 Connectors to Main BoardConnect to the Universal Monitor Overview of Menus Guide to Universal Monitor functions Main Menu Overview Opening Screen OverviewLCD Menu Overview View Status Options View Active Alarms Active AlarmsClearing Active Alarms Active Alarms View Alarm Log Alarm LogAlarm log conditions Main Menu Alarm Log View Event Log Event LogEvent Log Event log conditions Select a Sensor View Trend LogView a Trend Log Input Status View Input StatusViewing Additional Input Data View Output Status Output StatusViewing Additional Output Data Digital output states View Pager Numbers Select a PagerView a Pager Number View a Pager PIN Silence Alarm & Backup LOG Files Service Terminal Interface Silence Alarm Service Terminal Interface only Back Up Log Files Service Terminal Interface only Silence Alarm & Backup Log Files Service Terminal Interface Login LoginSystem and Control Options Valid characters for data entry Login Screen System & Control menu Setup System selectedSetup System menu System & Control menu Clear Alarms&Logs selected Setup System Overview Setup System Setup Input Change Label Name of Input Define Input as Alarmable or EventDefine Input as Normally Open or Normally Closed Set Up Alarmable Inputs in Latched or Unlatched Mode Set Up Delay TimeDelay Time Latched / Unlatched Setup System Setup Common Alarm Change to Reset Y or Not Reset NReset Common Alarm Setup Common Alarm Setup Sensor Select a Sensor to Configure Setup System Setup SensorDefault settings analog sensor inputs Change Sensor Label Name Identify the Sensor as ConnectedChange Units Label Change 20 mA Value Change 4 mA ValueChange Offset Value Set Up Alarmable Sensors in Latched or Unlatched Mode Define Sensor as Alarmable or EventMessage if sensor has been defined as an event Change Low Setpoint Change High SetpointChange Low Setpoint Change High Setpoint Sensor Delay Set Up Mapping for a Digital Input Setup System Setup I/O MatrixMap Input to a Main Board Output Default Mappings Digital Inputs to Outputs Default mapping of digital inputs to digital outputsDigital input By default, mapped to digital output Map Input to Expansion Board Output Set Up Mapping for an Analog Sensor Input Default Mappings Analog Inputs to OutputsMap Sensor to Main Board Output Map Sensor to Expansion Board Output Change Label Name of Output Setup System Setup OutputDefine Main Board Output as Normally Open / Closed Configure Main Board Output for Loss of Power Fail-Safe Set Expansion Board Output by DIP SwitchMessage if Expansion Board output selected Setup System Setup Modem & Pagers Modem Setup Initialization StringSupported Modem Settings Default Modem Settings Select Modem Setup Country codes Setup System MenuSetup Modem Menu International Dialing Enter Universal Monitor Phone Number Change Modem Hang Up Delay After a Call Enable Modem Diagnostic MessagesChange Modem Dial Prefix Pager Setup Pager Number and PIN Select a Pager to ConfigureSetup Pagers Setup Modem Pager dialing results Setup Pager Menu Enter a Pager NumberGuidelines for dialing pagers Enter a Pager PIN Number Enter Pager NUMBER40 Characters MAX Command Successful Enable Communications Check Enter Time To Perform Communications Check Setup System Setup System Info Select Setup SystemSetup System Info Setup EXP Board Setup System Info Change Password Change the PasswordReset Password to the Factory Default Aaaa Change Date & Time/Automatic Daylight Saving Time Setup Site ID Connect BatterySetup Site ID Battery alarms Backup and Upload Configuration File Back Up the Configuration File Upload the Configuration File Setup Serv Ph Num Enter Phone Number Service phone number dialing resultsGuidelines for dialing service phone number Setup Serv Ph Num Setup Service Phone Number Service Terminal Interface only Factory Defaults Factory DefaultsFirmware Update Service Terminal Interface only Factory Defaults System and Control Options Initiate Remote Alarm Test Service Terminal Interface only Disconnect Setup EXP Board Setup Exp Board Optional Expansion BoardExpansion Board Connected Manual Output Ctrl Clear Active Alarms Clear Alarms & LogsClear the Alarm Log Clear the Event Log Clear the Trend LogsClear Event Log Clear Trend Log Universal Monitor Specifications Specifications Optional Expansion Board Specifications Umexp Appendix a Service Terminal Interface Comparison of Functions LCD and Service Terminal Interface Steps to set up a direct or remote connection Connecting to the Service Terminal InterfaceConnection Methods Create a Connection Direct Connection via RS232Remote Connection via Modem Choose COM1 Choose the computer’s modem Set Up the COM1 Port Direct Connection Only COM1 Port Setup Set Up the Connection’s Properties Properties SetupAscii Setup Settings tab Click on the file name for example, Universal Monitor.ht Connect to the Service Terminal InterfaceDial button OK button Silence Alarm and Backup Log Files Setup Menu OverviewView Status Overview Main Menu For sample screens, see Main Menu View Status MenusMain Menu View Active Alarms View Active Alarms View Alarm Log View Alarm Log View Event Log View Event Log View Trend Log View Trend Log View Input Status View Input & Sensor Status View Output Status View Output Status View Pager Numbers View Pager Numbers Silence Alarm Section A.5.1 Section A.5.2 Back Up Alarm Log File Backup Log Files Alarm Log File Backup Log Files Event Log File Back Up Event Log File Backup Log Files Trend Log Files Back Up Trend Log Files Login Menu Setup MenuLogin Setup Menu Setup MenuTips on Using the Service Terminal Interface See Description Setup Input Setup Input Main Board Outputs Setup Input Expansion Board Inputs Setup Common Alarm Setup Common Alarm Setup Sensor Setup Sensor 110 Setup I/O Matrix Setup I-O Matrix Map Input to Output Main Board Inputs 112 Setup I-O Matrix Map Input to Output Expansion Board Inputs 114 Setup I-O Matrix Map Sensor to Output 116 Setup Output Setup Output Main Board Outputs Setup Output Expansion Board Outputs Pager Setup Setup Modem & PagersSetup Modem & Pagers Pager Setup Modem Setup Setup Modem & Pagers Modem Setup Setup System Info Setup System InfoChange Password Setup Site ID Change Date & Time Connect Battery Backup & Upload Configuration File Backup Backup & Upload Configuration File Upload Setup Service Phone NumberSetup Service Phone Number Factory Defaults Firmware Update Initiate Remote Alarm Test Connect Expansion Board Connect Expansion Board Override Output Override Output Main Board Outputs Override Output Expansion Board Outputs Clear Alarms & Logs Clear Active Alarms Clear Alarms & LogsClear Alarms & Logs Clear the Alarm Log Clear Alarms & Logs Clear the Event Log Clear Alarms & Logs Clear the Trend Logs Appendix B Default Settings Quick Reference Guide Universal Monitor default settings for inputs and outputs Universal Monitor other default settings Change Password Expansion Board default settings for inputs and outputs Expansion Board other default settingsPage Technical Support/Service Company Behind the ProductsLocations Asia 23F, Allied Kajima Bldg