Factory Defaults, Firmware Update | Liebert Universal Monitor

Setup Menu

Factory Defaults

For details on this feature, see 9.9.8 - Factory Defaults.

Factory Defaults

RESTORE FACTORY DEFAULTS

This command restores all panel information to factory settings

1=RESTORE FACTORY DEFAULTS 2=RETURN TO SETUP SYSTEM INFO MENU 3=RETURN TO SETUP MENU

4=RETURN TO MAIN MENU

SELECT A NUMBER:1

>RESTORE THE PANEL TO FACTORY SETTINGS-YES(Y) OR NO(N)? >[N]

[[

>COMMAND SUCCESSFUL

Firmware Update (Service Terminal Interface only)

For details on this feature, see 9.9.9 - Perform Firmware Update (Service Terminal Interface only).

Firmware Update

PERFORM FIRMWARE UPDATE

This command will update the existing firmware

1=PERFORM FIRMWARE UPDATE

2=RETURN TO SETUP SYSTEM INFO MENU 3=RETURN TO SETUP MENU

4=RETURN TO MAIN MENU

SELECT A NUMBER:1

>PERFORM FIRMWARE UPDATE-YES(Y) OR NO(N)? >[N]

>[

INSTRUCTIONS TO PERFORM FIRMWARE UPDATE:

ASSUMES USING MICROSOFT WINDOWS HYPERTERMINAL APPLICATION

-SELECT TRANSFER FROM THE TOOLBAR

-SELECT SEND FILE

-ENTER FILE NAME-FIRMWARE FILE LOCATION & NAME

-SELECT XMODEM FROM THE PROTOCOL BOX

-SELECT SEND BUTTON

>WAITING TO SEND PROGRAM FILE >DONE

>CHECKSUM IS....

>PROGRAM VERSION....

>WAITING TO SEND FLASH FILE

>DONE

>FIRMWARE UPDATE SUCCESSFUL

125

Image 133

Liebert Universal Monitor user manual Factory Defaults, Firmware Update

Contents

Monitoring Universal MonitorPage Table of Contents Opening Screen Overview Main Menu Overview LCD Menu Overview Setup System Setup I/O Matrix Appendix B Default Settings Quick Reference Guide Appendix a Service Terminal Interface Figures Page Optional Features Methods of Viewing and Configuring the Universal MonitorAvailable Alarms Data Logs Outside Enclosure Overview Enclosure has knockouts Access slotsOn top Transformer Module Back of LCD Controller Board Universal Monitor Main board RS232 Phone Line Typical ConfigurationDigital outputs Digital inputs Controller board components Controller Board Overview Connector EIA422 Of-power jumperEIA485 connector Connector RS232 Expansion board components Optional Expansion Board Overview LED indicators summary LED Indicators Color Description Power status LED Indicators Optional Expansion BoardEIA485 status LEDs D4 yellow D5 red General status LED D3 green Typical Sequence Installation Main Board Installation ConsiderationsPacking Contents Unpacking and Preliminary Inspection Required tools Surface-Mounting the Universal MonitorMounting the Panel Bottom hole diameter Flush-Mounting the Universal Monitor Input Power Connections Small Enclosure Connect Power to the Universal Monitor VAC Output Power Connections Input Power ConnectionsTermination and Mounting Large Enclosure Connection Type Connecting the Battery Pack Troubleshooting Transformer ModuleObtaining a Replacement Battery Pack Problem Possible Solution Replacement Fuse Part Numbers Packing manifest optional Expansion Board Installation Optional Expansion Board Surface-Mounting the Optional Expansion Board Mounting Dimensions optional Expansion Board Flush-Mounting the Optional Expansion Board Pre-wired Input Power Connections Optional Expansion Board24VAC wiring red & white 24VAC input connectors AC1 & AC2 TM115 shown Wiring and Connections Main Board Wiring SpecificationsWiring specifications main board Connecting Digital Inputs Connecting Digital Inputs and Digital OutputsConnecting Digital Outputs Proceeds up numbering keys are shown at right Setting the Digital Output Jumpers Connecting Analog InputsDigital output jumper settings Connecting the Analog Ground Setting the 12VDC/24VDC Analog Power Jumper EIA422 SiteScan Web Connector Connecting Common Alarm Outputs1 RS232 Connector Phone Line Connector Wiring specifications optional Expansion Board Wiring and Connections Optional Expansion Board Numbering keys Connecting Inputs and Outputs Numbering Relay is Closed On power failureKeys DIP switch setting outputs wired as Normally Closed N.C Setting the Digital Output DIP SwitchesDIP switch setting outputs wired as Normally Open N.O Enable the Connection via Firmware Connect EIA485 Connectors to Main BoardConnect to the Universal Monitor Guide to Universal Monitor functions Overview of Menus Main Menu Overview Opening Screen OverviewLCD Menu Overview View Status Options Active Alarms View Active AlarmsClearing Active Alarms Active Alarms Alarm Log View Alarm LogAlarm log conditions Main Menu Alarm Log Event Log View Event LogEvent Log Event log conditions Select a Sensor View Trend LogView a Trend Log Input Status View Input StatusViewing Additional Input Data Output Status View Output StatusViewing Additional Output Data Digital output states Select a Pager View Pager NumbersView a Pager Number View a Pager PIN Silence Alarm Service Terminal Interface only Silence Alarm & Backup LOG Files Service Terminal Interface Back Up Log Files Service Terminal Interface only Silence Alarm & Backup Log Files Service Terminal Interface Login LoginSystem and Control Options Valid characters for data entry System & Control menu Setup System selected Login ScreenSetup System menu System & Control menu Clear Alarms&Logs selected Setup System Setup Input Setup System Overview Change Label Name of Input Define Input as Alarmable or EventDefine Input as Normally Open or Normally Closed Set Up Delay Time Set Up Alarmable Inputs in Latched or Unlatched ModeDelay Time Latched / Unlatched Change to Reset Y or Not Reset N Setup System Setup Common AlarmReset Common Alarm Setup Common Alarm Setup Sensor Select a Sensor to Configure Setup System Setup SensorDefault settings analog sensor inputs Change Sensor Label Name Identify the Sensor as ConnectedChange Units Label Change 20 mA Value Change 4 mA ValueChange Offset Value Set Up Alarmable Sensors in Latched or Unlatched Mode Define Sensor as Alarmable or EventMessage if sensor has been defined as an event Change High Setpoint Change Low SetpointChange Low Setpoint Change High Setpoint Sensor Delay Set Up Mapping for a Digital Input Setup System Setup I/O MatrixMap Input to a Main Board Output Default mapping of digital inputs to digital outputs Default Mappings Digital Inputs to OutputsDigital input By default, mapped to digital output Map Input to Expansion Board Output Default Mappings Analog Inputs to Outputs Set Up Mapping for an Analog Sensor InputMap Sensor to Main Board Output Map Sensor to Expansion Board Output Change Label Name of Output Setup System Setup OutputDefine Main Board Output as Normally Open / Closed Configure Main Board Output for Loss of Power Fail-Safe Set Expansion Board Output by DIP SwitchMessage if Expansion Board output selected Modem Setup Initialization String Setup System Setup Modem & PagersSupported Modem Settings Default Modem Settings Country codes Setup System Menu Select Modem SetupSetup Modem Menu International Dialing Enter Universal Monitor Phone Number Change Modem Hang Up Delay After a Call Enable Modem Diagnostic MessagesChange Modem Dial Prefix Select a Pager to Configure Pager Setup Pager Number and PINSetup Pagers Setup Modem Pager dialing results Enter a Pager Number Setup Pager MenuGuidelines for dialing pagers Enter a Pager PIN Number Enter Pager NUMBER40 Characters MAX Command Successful Enter Time To Perform Communications Check Enable Communications Check Select Setup System Setup System Setup System InfoSetup System Info Setup EXP Board Setup System Info Change the Password Change PasswordReset Password to the Factory Default Aaaa Change Date & Time/Automatic Daylight Saving Time Connect Battery Setup Site IDSetup Site ID Battery alarms Backup and Upload Configuration File Back Up the Configuration File Upload the Configuration File Service phone number dialing results Setup Serv Ph Num Enter Phone NumberGuidelines for dialing service phone number Setup Serv Ph Num Setup Service Phone Number Service Terminal Interface only Factory Defaults Factory DefaultsFirmware Update Service Terminal Interface only Factory Defaults System and Control Options Disconnect Initiate Remote Alarm Test Service Terminal Interface only Setup EXP Board Setup Exp Board Optional Expansion BoardExpansion Board Connected Manual Output Ctrl Clear Active Alarms Clear Alarms & LogsClear the Alarm Log Clear the Trend Logs Clear the Event LogClear Event Log Clear Trend Log Specifications Universal Monitor Specifications Umexp Optional Expansion Board Specifications Comparison of Functions LCD and Service Terminal Interface Appendix a Service Terminal Interface Steps to set up a direct or remote connection Connecting to the Service Terminal InterfaceConnection Methods Direct Connection via RS232 Create a ConnectionRemote Connection via Modem Choose COM1 Choose the computer’s modem COM1 Port Setup Set Up the COM1 Port Direct Connection Only Properties Setup Set Up the Connection’s PropertiesAscii Setup Settings tab Click on the file name for example, Universal Monitor.ht Connect to the Service Terminal InterfaceDial button OK button Setup Menu Overview Silence Alarm and Backup Log FilesView Status Overview Main Menu For sample screens, see Main Menu View Status MenusMain Menu View Active Alarms View Active Alarms View Alarm Log View Alarm Log View Event Log View Event Log View Trend Log View Trend Log View Input & Sensor Status View Input Status View Output Status View Output Status View Pager Numbers View Pager Numbers Section A.5.1 Section A.5.2 Silence Alarm Backup Log Files Alarm Log File Back Up Alarm Log File Back Up Event Log File Backup Log Files Event Log File Back Up Trend Log Files Backup Log Files Trend Log Files Login Menu Setup MenuLogin Setup Menu Setup MenuTips on Using the Service Terminal Interface See Description Setup Input Main Board Outputs Setup Input Setup Input Expansion Board Inputs Setup Common Alarm Setup Common Alarm Setup Sensor Setup Sensor 110 Setup I-O Matrix Map Input to Output Main Board Inputs Setup I/O Matrix 112 Setup I-O Matrix Map Input to Output Expansion Board Inputs 114 Setup I-O Matrix Map Sensor to Output 116 Setup Output Main Board Outputs Setup Output Setup Output Expansion Board Outputs Pager Setup Setup Modem & PagersSetup Modem & Pagers Pager Setup Setup Modem & Pagers Modem Setup Modem Setup Setup System Info Setup System InfoChange Password Change Date & Time Setup Site ID Backup & Upload Configuration File Backup Connect Battery Backup & Upload Configuration File Upload Setup Service Phone NumberSetup Service Phone Number Firmware Update Factory Defaults Initiate Remote Alarm Test Connect Expansion Board Connect Expansion Board Override Output Main Board Outputs Override Output Override Output Expansion Board Outputs Clear Alarms & Logs Clear Active Alarms Clear Alarms & LogsClear Alarms & Logs Clear the Alarm Log Clear Alarms & Logs Clear the Trend Logs Clear Alarms & Logs Clear the Event Log Universal Monitor default settings for inputs and outputs Appendix B Default Settings Quick Reference Guide Change Password Universal Monitor other default settings Expansion Board other default settings Expansion Board default settings for inputs and outputsPage Company Behind the Products Technical Support/ServiceLocations Asia 23F, Allied Kajima Bldg