Company Behind the Products, Locations | Liebert Universal Monitor

MONITORING

UNIVERSAL MONITOR

USER MANUAL

The Company Behind the Products

With over a million installations around the globe, Liebert is the world leader in computer protection systems. Since its founding in 1965, Liebert has developed a complete range of support and protection systems for sensitive electronics:

•Environmental systems—close-control air conditioning from 1 to 60 tons

•Power conditioning and UPS with power ranges from 300 VA to more than 1000 kVA

•Integrated systems that provide both environmental and power protection in a single, flexible package

•Monitoring and control—from systems of any size or location, on-site or remote

•Service and support through more than 100 service centers around the world and a 24/7 Customer Response Center

While every precaution has been taken to ensure the accuracy and completeness of this literature, Liebert Corporation assumes no responsibility and disclaims all liability for damages resulting from use of this information or for any errors or omissions.

© 2004 Liebert Corporation

All rights reserved throughout the world. Specifications subject to change without notice.

®Liebert and the Liebert logo are registered trademarks of Liebert Corporation. All names referred to are trademarks or registered trademarks of their respective owners.

SL-31060 (8/04) Rev. 1

Technical Support/Service

Web Site

www.liebert.com

Monitoring 800-222-5877 monitoring@liebert.com Outside the US: 614-841-6755

Single-Phase UPS 800-222-5877 upstech@liebert.com Outside the US: 614-841-6755

Three-Phase UPS 800-543-2378 powertech@liebert.com

Environmental Systems

800-543-2778

Outside the United States

614-888-0246

Locations

United States 1050 Dearborn Drive P.O. Box 29186 Columbus, OH 43229

Italy Via Leonardo Da Vinci 8 Zona Industriale Tognana 35028 Piove Di Sacco (PD) +39 049 9719 111 Fax: +39 049 5841 257

Asia 23F, Allied Kajima Bldg.

138 Gloucester Road Wanchai Hong Kong

+852 2 572 2201 Fax: +852 2 831 0114

Image 144

Liebert Universal Monitor Company Behind the Products, Technical Support/Service, Locations, Asia 23F, Allied Kajima Bldg

Contents

Universal Monitor MonitoringPage Table of Contents Opening Screen Overview Main Menu Overview LCD Menu Overview Setup System Setup I/O Matrix Appendix a Service Terminal Interface Appendix B Default Settings Quick Reference Guide Figures Page Methods of Viewing and Configuring the Universal Monitor Optional FeaturesAvailable Alarms Data Logs Enclosure has knockouts Access slots Outside Enclosure OverviewOn top Transformer Module Back of LCD Controller Board Typical Configuration Universal Monitor Main board RS232 Phone LineDigital outputs Digital inputs Controller Board Overview Controller board components Of-power jumper Connector EIA422EIA485 connector Connector RS232 Optional Expansion Board Overview Expansion board components LED Indicators LED indicators summary LED Indicators Optional Expansion Board Color Description Power statusEIA485 status LEDs D4 yellow D5 red General status LED D3 green Typical Sequence Installation Considerations Installation Main BoardPacking Contents Unpacking and Preliminary Inspection Surface-Mounting the Universal Monitor Required toolsMounting the Panel Bottom hole diameter Flush-Mounting the Universal Monitor Connect Power to the Universal Monitor Input Power Connections Small Enclosure Input Power Connections VAC Output Power ConnectionsTermination and Mounting Large Enclosure Connection Type Troubleshooting Transformer Module Connecting the Battery PackObtaining a Replacement Battery Pack Problem Possible Solution Replacement Fuse Part Numbers Installation Optional Expansion Board Packing manifest optional Expansion Board Mounting Dimensions optional Expansion Board Surface-Mounting the Optional Expansion Board Flush-Mounting the Optional Expansion Board Input Power Connections Optional Expansion Board Pre-wired24VAC wiring red & white 24VAC input connectors AC1 & AC2 TM115 shown Wiring Specifications Wiring and Connections Main BoardWiring specifications main board Connecting Digital Inputs and Digital Outputs Connecting Digital InputsConnecting Digital Outputs Proceeds up numbering keys are shown at right Connecting Analog Inputs Setting the Digital Output JumpersDigital output jumper settings Setting the 12VDC/24VDC Analog Power Jumper Connecting the Analog Ground Connecting Common Alarm Outputs EIA422 SiteScan Web Connector1 RS232 Connector Phone Line Connector Wiring and Connections Optional Expansion Board Wiring specifications optional Expansion Board Connecting Inputs and Outputs Numbering keys Relay is Closed On power failure NumberingKeys Setting the Digital Output DIP Switches DIP switch setting outputs wired as Normally Closed N.CDIP switch setting outputs wired as Normally Open N.O Connect EIA485 Connectors to Main Board Enable the Connection via FirmwareConnect to the Universal Monitor Overview of Menus Guide to Universal Monitor functions Opening Screen Overview Main Menu OverviewLCD Menu Overview View Status Options View Active Alarms Active AlarmsClearing Active Alarms Active Alarms View Alarm Log Alarm LogAlarm log conditions Main Menu Alarm Log View Event Log Event LogEvent Log Event log conditions View Trend Log Select a SensorView a Trend Log View Input Status Input StatusViewing Additional Input Data View Output Status Output StatusViewing Additional Output Data Digital output states View Pager Numbers Select a PagerView a Pager Number View a Pager PIN Silence Alarm & Backup LOG Files Service Terminal Interface Silence Alarm Service Terminal Interface only Back Up Log Files Service Terminal Interface only Silence Alarm & Backup Log Files Service Terminal Interface Login LoginSystem and Control Options Valid characters for data entry Login Screen System & Control menu Setup System selectedSetup System menu System & Control menu Clear Alarms&Logs selected Setup System Overview Setup System Setup Input Define Input as Alarmable or Event Change Label Name of InputDefine Input as Normally Open or Normally Closed Set Up Alarmable Inputs in Latched or Unlatched Mode Set Up Delay TimeDelay Time Latched / Unlatched Setup System Setup Common Alarm Change to Reset Y or Not Reset NReset Common Alarm Setup Common Alarm Setup Sensor Setup System Setup Sensor Select a Sensor to ConfigureDefault settings analog sensor inputs Identify the Sensor as Connected Change Sensor Label NameChange Units Label Change 4 mA Value Change 20 mA ValueChange Offset Value Define Sensor as Alarmable or Event Set Up Alarmable Sensors in Latched or Unlatched ModeMessage if sensor has been defined as an event Change Low Setpoint Change High SetpointChange Low Setpoint Change High Setpoint Sensor Delay Setup System Setup I/O Matrix Set Up Mapping for a Digital InputMap Input to a Main Board Output Default Mappings Digital Inputs to Outputs Default mapping of digital inputs to digital outputsDigital input By default, mapped to digital output Map Input to Expansion Board Output Set Up Mapping for an Analog Sensor Input Default Mappings Analog Inputs to OutputsMap Sensor to Main Board Output Map Sensor to Expansion Board Output Setup System Setup Output Change Label Name of OutputDefine Main Board Output as Normally Open / Closed Set Expansion Board Output by DIP Switch Configure Main Board Output for Loss of Power Fail-SafeMessage if Expansion Board output selected Setup System Setup Modem & Pagers Modem Setup Initialization StringSupported Modem Settings Default Modem Settings Select Modem Setup Country codes Setup System MenuSetup Modem Menu International Dialing Enter Universal Monitor Phone Number Enable Modem Diagnostic Messages Change Modem Hang Up Delay After a CallChange Modem Dial Prefix Pager Setup Pager Number and PIN Select a Pager to ConfigureSetup Pagers Setup Modem Pager dialing results Setup Pager Menu Enter a Pager NumberGuidelines for dialing pagers Enter a Pager PIN Number Enter Pager NUMBER40 Characters MAX Command Successful Enable Communications Check Enter Time To Perform Communications Check Setup System Setup System Info Select Setup SystemSetup System Info Setup EXP Board Setup System Info Change Password Change the PasswordReset Password to the Factory Default Aaaa Change Date & Time/Automatic Daylight Saving Time Setup Site ID Connect BatterySetup Site ID Battery alarms Backup and Upload Configuration File Back Up the Configuration File Upload the Configuration File Setup Serv Ph Num Enter Phone Number Service phone number dialing resultsGuidelines for dialing service phone number Setup Serv Ph Num Setup Service Phone Number Service Terminal Interface only Factory Defaults Factory DefaultsFirmware Update Service Terminal Interface only Factory Defaults System and Control Options Initiate Remote Alarm Test Service Terminal Interface only Disconnect Setup Exp Board Optional Expansion Board Setup EXP BoardExpansion Board Connected Manual Output Ctrl Clear Alarms & Logs Clear Active AlarmsClear the Alarm Log Clear the Event Log Clear the Trend LogsClear Event Log Clear Trend Log Universal Monitor Specifications Specifications Optional Expansion Board Specifications Umexp Appendix a Service Terminal Interface Comparison of Functions LCD and Service Terminal Interface Connecting to the Service Terminal Interface Steps to set up a direct or remote connectionConnection Methods Create a Connection Direct Connection via RS232Remote Connection via Modem Choose COM1 Choose the computer’s modem Set Up the COM1 Port Direct Connection Only COM1 Port Setup Set Up the Connection’s Properties Properties SetupAscii Setup Settings tab Connect to the Service Terminal Interface Click on the file name for example, Universal Monitor.htDial button OK button Silence Alarm and Backup Log Files Setup Menu OverviewView Status Overview Main Menu For sample screens, see View Status Menus Main MenuMain Menu View Active Alarms View Active Alarms View Alarm Log View Alarm Log View Event Log View Event Log View Trend Log View Trend Log View Input Status View Input & Sensor Status View Output Status View Output Status View Pager Numbers View Pager Numbers Silence Alarm Section A.5.1 Section A.5.2 Back Up Alarm Log File Backup Log Files Alarm Log File Backup Log Files Event Log File Back Up Event Log File Backup Log Files Trend Log Files Back Up Trend Log Files Setup Menu Login MenuLogin Setup Menu Setup MenuTips on Using the Service Terminal Interface See Description Setup Input Setup Input Main Board Outputs Setup Input Expansion Board Inputs Setup Common Alarm Setup Common Alarm Setup Sensor Setup Sensor 110 Setup I/O Matrix Setup I-O Matrix Map Input to Output Main Board Inputs 112 Setup I-O Matrix Map Input to Output Expansion Board Inputs 114 Setup I-O Matrix Map Sensor to Output 116 Setup Output Setup Output Main Board Outputs Setup Output Expansion Board Outputs Setup Modem & Pagers Pager SetupSetup Modem & Pagers Pager Setup Modem Setup Setup Modem & Pagers Modem Setup Setup System Info Setup System InfoChange Password Setup Site ID Change Date & Time Connect Battery Backup & Upload Configuration File Backup Setup Service Phone Number Backup & Upload Configuration File UploadSetup Service Phone Number Factory Defaults Firmware Update Initiate Remote Alarm Test Connect Expansion Board Connect Expansion Board Override Output Override Output Main Board Outputs Override Output Expansion Board Outputs Clear Alarms & Logs Clear Alarms & Logs Clear Active AlarmsClear Alarms & Logs Clear the Alarm Log Clear Alarms & Logs Clear the Event Log Clear Alarms & Logs Clear the Trend Logs Appendix B Default Settings Quick Reference Guide Universal Monitor default settings for inputs and outputs Universal Monitor other default settings Change Password Expansion Board default settings for inputs and outputs Expansion Board other default settingsPage Technical Support/Service Company Behind the ProductsLocations Asia 23F, Allied Kajima Bldg