Setup System Setup Common Alarm | Liebert Universal Monitor instruction

System and Control Options

9.4Setup System - Setup Common Alarm

The audible alarm sounds after the Universal Monitor detects an alarm condition in any input that has been defined as alarmable, including digital and analog sensor inputs. Once the alarm is silenced, there are two options:

•By default, the common alarm remains energized until the input alarm is cleared.

•You may change this setting to de-energize the common alarm automatically once the alarm is silenced.

You might want to reset the common alarm with silence if an external alarm—for example, a horn—is connected to the common alarm output contacts.

You might not want to reset the common alarm contacts (let contacts reflect/track alarms) and simply silence the audible horn.

To change the common alarm setting:

Log In and Choose Setup System

•From the Main Menu, use the arrows ↑ ↓ to choose System and Control, then press Enter ↵ (see 9.1 - Login for help).

•Enter your password at the Login screen.

•From the System and Control Menu, use the arrows ↑ ↓ to choose Setup System, then press Enter ↵ .

Change to Reset (Y) or Not Reset (N)

•From the Setup System Menu, shown at right, use the arrows ↑ ↓ to choose Setup Common Alarm and press Enter ↵ .

•By default, the common alarm is set up not to reset automatically when the alarm is silenced (N). To change this setting, use the arrows ↑ ↓ to choose Y (Yes - reset with silence) or N (No - not reset), then press Enter ↵ .

Setup System Menu

SETUP INPUT

>SETUP COMMON ALARM SETUP SENSOR

SETUP I/O MATRIX

↑ ↓=NEXT ↵ =SELECT

SETUP OUTPUT SETUP MODEM&PAGERS SETUP SYSTEM INFO SETUP EXP BOARD

Reset Common Alarm

RESET COMMON ALARM WITH SILENCE? N

↑ ↓=Y/N

↵ =END

48

Image 56

Liebert Universal Monitor user manual Setup System Setup Common Alarm, Change to Reset Y or Not Reset N, Reset Common Alarm

Contents

Universal Monitor MonitoringPage Table of Contents Opening Screen Overview Main Menu Overview LCD Menu Overview Setup System Setup I/O Matrix Appendix a Service Terminal Interface Appendix B Default Settings Quick Reference Guide Figures Page Methods of Viewing and Configuring the Universal Monitor Optional FeaturesAvailable Alarms Data Logs Enclosure has knockouts Access slots Outside Enclosure OverviewOn top Transformer Module Back of LCD Controller Board Typical Configuration Universal Monitor Main board RS232 Phone LineDigital outputs Digital inputs Controller Board Overview Controller board components Of-power jumper Connector EIA422EIA485 connector Connector RS232 Optional Expansion Board Overview Expansion board components LED Indicators LED indicators summary LED Indicators Optional Expansion Board Color Description Power statusEIA485 status LEDs D4 yellow D5 red General status LED D3 green Typical Sequence Installation Considerations Installation Main BoardPacking Contents Unpacking and Preliminary Inspection Surface-Mounting the Universal Monitor Required toolsMounting the Panel Bottom hole diameter Flush-Mounting the Universal Monitor Connect Power to the Universal Monitor Input Power Connections Small Enclosure Input Power Connections VAC Output Power ConnectionsTermination and Mounting Large Enclosure Connection Type Troubleshooting Transformer Module Connecting the Battery PackObtaining a Replacement Battery Pack Problem Possible Solution Replacement Fuse Part Numbers Installation Optional Expansion Board Packing manifest optional Expansion Board Mounting Dimensions optional Expansion Board Surface-Mounting the Optional Expansion Board Flush-Mounting the Optional Expansion Board Input Power Connections Optional Expansion Board Pre-wired24VAC wiring red & white 24VAC input connectors AC1 & AC2 TM115 shown Wiring specifications main board Wiring SpecificationsWiring and Connections Main Board Connecting Digital Inputs and Digital Outputs Connecting Digital InputsConnecting Digital Outputs Proceeds up numbering keys are shown at right Digital output jumper settings Connecting Analog InputsSetting the Digital Output Jumpers Setting the 12VDC/24VDC Analog Power Jumper Connecting the Analog Ground Connecting Common Alarm Outputs EIA422 SiteScan Web Connector1 RS232 Connector Phone Line Connector Wiring and Connections Optional Expansion Board Wiring specifications optional Expansion Board Connecting Inputs and Outputs Numbering keys Keys Relay is Closed On power failureNumbering DIP switch setting outputs wired as Normally Open N.O Setting the Digital Output DIP SwitchesDIP switch setting outputs wired as Normally Closed N.C Connect to the Universal Monitor Connect EIA485 Connectors to Main BoardEnable the Connection via Firmware Overview of Menus Guide to Universal Monitor functions LCD Menu Overview Opening Screen OverviewMain Menu Overview View Status Options View Active Alarms Active AlarmsClearing Active Alarms Active Alarms View Alarm Log Alarm LogAlarm log conditions Main Menu Alarm Log View Event Log Event LogEvent Log Event log conditions View a Trend Log View Trend LogSelect a Sensor Viewing Additional Input Data View Input StatusInput Status View Output Status Output StatusViewing Additional Output Data Digital output states View Pager Numbers Select a PagerView a Pager Number View a Pager PIN Silence Alarm & Backup LOG Files Service Terminal Interface Silence Alarm Service Terminal Interface only Back Up Log Files Service Terminal Interface only Silence Alarm & Backup Log Files Service Terminal Interface Login LoginSystem and Control Options Valid characters for data entry Login Screen System & Control menu Setup System selectedSetup System menu System & Control menu Clear Alarms&Logs selected Setup System Overview Setup System Setup Input Define Input as Normally Open or Normally Closed Define Input as Alarmable or EventChange Label Name of Input Set Up Alarmable Inputs in Latched or Unlatched Mode Set Up Delay TimeDelay Time Latched / Unlatched Setup System Setup Common Alarm Change to Reset Y or Not Reset NReset Common Alarm Setup Common Alarm Setup Sensor Default settings analog sensor inputs Setup System Setup SensorSelect a Sensor to Configure Change Units Label Identify the Sensor as ConnectedChange Sensor Label Name Change Offset Value Change 4 mA ValueChange 20 mA Value Message if sensor has been defined as an event Define Sensor as Alarmable or EventSet Up Alarmable Sensors in Latched or Unlatched Mode Change Low Setpoint Change High SetpointChange Low Setpoint Change High Setpoint Sensor Delay Map Input to a Main Board Output Setup System Setup I/O MatrixSet Up Mapping for a Digital Input Default Mappings Digital Inputs to Outputs Default mapping of digital inputs to digital outputsDigital input By default, mapped to digital output Map Input to Expansion Board Output Set Up Mapping for an Analog Sensor Input Default Mappings Analog Inputs to OutputsMap Sensor to Main Board Output Map Sensor to Expansion Board Output Define Main Board Output as Normally Open / Closed Setup System Setup OutputChange Label Name of Output Message if Expansion Board output selected Set Expansion Board Output by DIP SwitchConfigure Main Board Output for Loss of Power Fail-Safe Setup System Setup Modem & Pagers Modem Setup Initialization StringSupported Modem Settings Default Modem Settings Select Modem Setup Country codes Setup System MenuSetup Modem Menu International Dialing Enter Universal Monitor Phone Number Change Modem Dial Prefix Enable Modem Diagnostic MessagesChange Modem Hang Up Delay After a Call Pager Setup Pager Number and PIN Select a Pager to ConfigureSetup Pagers Setup Modem Pager dialing results Setup Pager Menu Enter a Pager NumberGuidelines for dialing pagers Enter a Pager PIN Number Enter Pager NUMBER40 Characters MAX Command Successful Enable Communications Check Enter Time To Perform Communications Check Setup System Setup System Info Select Setup SystemSetup System Info Setup EXP Board Setup System Info Change Password Change the PasswordReset Password to the Factory Default Aaaa Change Date & Time/Automatic Daylight Saving Time Setup Site ID Connect BatterySetup Site ID Battery alarms Backup and Upload Configuration File Back Up the Configuration File Upload the Configuration File Setup Serv Ph Num Enter Phone Number Service phone number dialing resultsGuidelines for dialing service phone number Setup Serv Ph Num Setup Service Phone Number Service Terminal Interface only Factory Defaults Factory DefaultsFirmware Update Service Terminal Interface only Factory Defaults System and Control Options Initiate Remote Alarm Test Service Terminal Interface only Disconnect Expansion Board Connected Setup Exp Board Optional Expansion BoardSetup EXP Board Manual Output Ctrl Clear the Alarm Log Clear Alarms & LogsClear Active Alarms Clear the Event Log Clear the Trend LogsClear Event Log Clear Trend Log Universal Monitor Specifications Specifications Optional Expansion Board Specifications Umexp Appendix a Service Terminal Interface Comparison of Functions LCD and Service Terminal Interface Connection Methods Connecting to the Service Terminal InterfaceSteps to set up a direct or remote connection Create a Connection Direct Connection via RS232Remote Connection via Modem Choose COM1 Choose the computer’s modem Set Up the COM1 Port Direct Connection Only COM1 Port Setup Set Up the Connection’s Properties Properties SetupAscii Setup Settings tab Dial button OK button Connect to the Service Terminal InterfaceClick on the file name for example, Universal Monitor.ht Silence Alarm and Backup Log Files Setup Menu OverviewView Status Overview Main Menu For sample screens, see Main Menu View Status MenusMain Menu View Active Alarms View Active Alarms View Alarm Log View Alarm Log View Event Log View Event Log View Trend Log View Trend Log View Input Status View Input & Sensor Status View Output Status View Output Status View Pager Numbers View Pager Numbers Silence Alarm Section A.5.1 Section A.5.2 Back Up Alarm Log File Backup Log Files Alarm Log File Backup Log Files Event Log File Back Up Event Log File Backup Log Files Trend Log Files Back Up Trend Log Files Login Setup MenuLogin Menu Setup Menu Setup MenuTips on Using the Service Terminal Interface See Description Setup Input Setup Input Main Board Outputs Setup Input Expansion Board Inputs Setup Common Alarm Setup Common Alarm Setup Sensor Setup Sensor 110 Setup I/O Matrix Setup I-O Matrix Map Input to Output Main Board Inputs 112 Setup I-O Matrix Map Input to Output Expansion Board Inputs 114 Setup I-O Matrix Map Sensor to Output 116 Setup Output Setup Output Main Board Outputs Setup Output Expansion Board Outputs Setup Modem & Pagers Pager Setup Setup Modem & PagersPager Setup Modem Setup Setup Modem & Pagers Modem Setup Change Password Setup System InfoSetup System Info Setup Site ID Change Date & Time Connect Battery Backup & Upload Configuration File Backup Setup Service Phone Number Setup Service Phone NumberBackup & Upload Configuration File Upload Factory Defaults Firmware Update Initiate Remote Alarm Test Connect Expansion Board Connect Expansion Board Override Output Override Output Main Board Outputs Override Output Expansion Board Outputs Clear Alarms & Logs Clear the Alarm Log Clear Alarms & LogsClear Alarms & Logs Clear Active Alarms Clear Alarms & Logs Clear the Event Log Clear Alarms & Logs Clear the Trend Logs Appendix B Default Settings Quick Reference Guide Universal Monitor default settings for inputs and outputs Universal Monitor other default settings Change Password Expansion Board default settings for inputs and outputs Expansion Board other default settingsPage Technical Support/Service Company Behind the ProductsLocations Asia 23F, Allied Kajima Bldg