Change Password | Liebert Universal Monitor instruction

			Default Settings Quick Reference Guide
	Table 38 Universal Monitor - other default settings
	JUMPER SETTINGS
	Feature	Default	Other Options
	Digital output loss-of-power jumpers	OFF - Normally Open	ON - Normally Closed

	Note: Jumper position has no effect when the Universal Monitor has power.
	12VDC/24VDC analog input jumper	24VDC	Acceptable voltage for all four two-wire analog sensors

	P20 jumper	Not jumpered (not	—
	P20 jumper	connected)	—
		connected)
	422 TERM jumper	Default: jumpered	—
	422 TERM jumper	(connected)	—
		(connected)
	485 TERM jumper	Default: jumpered	—
	485 TERM jumper	(connected)	—
		(connected)
	Audible horn	Enabled	May be disabled via the audible horn jumper
	Manual Override switch	Off (outputs controlled by	On (Turn on all output relays)
		programming)
	DEFAULT SETTINGS - MODEM (FROM	TABLE 27)
	Feature	Default	Other Options
			Any string (up to 40 characters); for international
	Initialization String (Init String)	ATS0=1	dialing, add +GCI=xx, where xx is the country code
			(except B5 countries—see Table 27)
	Enable Modem Diagnostic Messages	N (disable)	Y (enable)
	Modem Dial Prefix	ATE0X4DT	Any string
	Modem Hang Up Delay After a Call	10 seconds	Any number (up to 99 seconds)
	DIP SWITCH SETTINGS
	Feature	Default	Other Options
	8-position DIP switch	All are OFF (down)	May be used to reset password to factory default (see
	8-position DIP switch	All are OFF (down)	9.9.1 - Change Password)
			9.9.1 - Change Password)
	OTHER SETTINGS
	Feature	Default	Other Options
	Change state of outputs - automatic	AUTO (automatic control)	Force an output ON / OFF via Manual Output Ctrl menu
	or manual control	AUTO (automatic control)	Force all outputs ON via hardware switch
	Password	AAAA	Any 4 characters (see Table 20 for valid characters)
	Reset common alarm with silence	N (not reset)	Y (reset with silence)
	Battery connected	Y (connected)	N (not connected)

133

Image 141

Liebert user manual Universal Monitor other default settings, Change Password

Contents

Monitoring Universal MonitorPage Table of Contents Opening Screen Overview Main Menu Overview LCD Menu Overview Setup System Setup I/O Matrix Appendix B Default Settings Quick Reference Guide Appendix a Service Terminal Interface Figures Page Optional Features Methods of Viewing and Configuring the Universal MonitorAvailable Alarms Data Logs Outside Enclosure Overview Enclosure has knockouts Access slotsOn top Transformer Module Back of LCD Controller Board Universal Monitor Main board RS232 Phone Line Typical ConfigurationDigital outputs Digital inputs Controller board components Controller Board Overview Connector EIA422 Of-power jumperEIA485 connector Connector RS232 Expansion board components Optional Expansion Board Overview LED indicators summary LED Indicators Color Description Power status LED Indicators Optional Expansion BoardEIA485 status LEDs D4 yellow D5 red General status LED D3 green Typical Sequence Installation Main Board Installation ConsiderationsPacking Contents Unpacking and Preliminary Inspection Required tools Surface-Mounting the Universal MonitorMounting the Panel Bottom hole diameter Flush-Mounting the Universal Monitor Input Power Connections Small Enclosure Connect Power to the Universal Monitor VAC Output Power Connections Input Power ConnectionsTermination and Mounting Large Enclosure Connection Type Connecting the Battery Pack Troubleshooting Transformer ModuleObtaining a Replacement Battery Pack Problem Possible Solution Replacement Fuse Part Numbers Packing manifest optional Expansion Board Installation Optional Expansion Board Surface-Mounting the Optional Expansion Board Mounting Dimensions optional Expansion Board Flush-Mounting the Optional Expansion Board Pre-wired Input Power Connections Optional Expansion Board24VAC wiring red & white 24VAC input connectors AC1 & AC2 TM115 shown Wiring Specifications Wiring and Connections Main BoardWiring specifications main board Connecting Digital Inputs Connecting Digital Inputs and Digital OutputsConnecting Digital Outputs Proceeds up numbering keys are shown at right Connecting Analog Inputs Setting the Digital Output JumpersDigital output jumper settings Connecting the Analog Ground Setting the 12VDC/24VDC Analog Power Jumper EIA422 SiteScan Web Connector Connecting Common Alarm Outputs1 RS232 Connector Phone Line Connector Wiring specifications optional Expansion Board Wiring and Connections Optional Expansion Board Numbering keys Connecting Inputs and Outputs Relay is Closed On power failure NumberingKeys Setting the Digital Output DIP Switches DIP switch setting outputs wired as Normally Closed N.CDIP switch setting outputs wired as Normally Open N.O Connect EIA485 Connectors to Main Board Enable the Connection via FirmwareConnect to the Universal Monitor Guide to Universal Monitor functions Overview of Menus Opening Screen Overview Main Menu OverviewLCD Menu Overview View Status Options Active Alarms View Active AlarmsClearing Active Alarms Active Alarms Alarm Log View Alarm LogAlarm log conditions Main Menu Alarm Log Event Log View Event LogEvent Log Event log conditions View Trend Log Select a SensorView a Trend Log View Input Status Input StatusViewing Additional Input Data Output Status View Output StatusViewing Additional Output Data Digital output states Select a Pager View Pager NumbersView a Pager Number View a Pager PIN Silence Alarm Service Terminal Interface only Silence Alarm & Backup LOG Files Service Terminal Interface Back Up Log Files Service Terminal Interface only Silence Alarm & Backup Log Files Service Terminal Interface Login LoginSystem and Control Options Valid characters for data entry System & Control menu Setup System selected Login ScreenSetup System menu System & Control menu Clear Alarms&Logs selected Setup System Setup Input Setup System Overview Define Input as Alarmable or Event Change Label Name of InputDefine Input as Normally Open or Normally Closed Set Up Delay Time Set Up Alarmable Inputs in Latched or Unlatched ModeDelay Time Latched / Unlatched Change to Reset Y or Not Reset N Setup System Setup Common AlarmReset Common Alarm Setup Common Alarm Setup Sensor Setup System Setup Sensor Select a Sensor to ConfigureDefault settings analog sensor inputs Identify the Sensor as Connected Change Sensor Label NameChange Units Label Change 4 mA Value Change 20 mA ValueChange Offset Value Define Sensor as Alarmable or Event Set Up Alarmable Sensors in Latched or Unlatched ModeMessage if sensor has been defined as an event Change High Setpoint Change Low SetpointChange Low Setpoint Change High Setpoint Sensor Delay Setup System Setup I/O Matrix Set Up Mapping for a Digital InputMap Input to a Main Board Output Default mapping of digital inputs to digital outputs Default Mappings Digital Inputs to OutputsDigital input By default, mapped to digital output Map Input to Expansion Board Output Default Mappings Analog Inputs to Outputs Set Up Mapping for an Analog Sensor InputMap Sensor to Main Board Output Map Sensor to Expansion Board Output Setup System Setup Output Change Label Name of OutputDefine Main Board Output as Normally Open / Closed Set Expansion Board Output by DIP Switch Configure Main Board Output for Loss of Power Fail-SafeMessage if Expansion Board output selected Modem Setup Initialization String Setup System Setup Modem & PagersSupported Modem Settings Default Modem Settings Country codes Setup System Menu Select Modem SetupSetup Modem Menu International Dialing Enter Universal Monitor Phone Number Enable Modem Diagnostic Messages Change Modem Hang Up Delay After a CallChange Modem Dial Prefix Select a Pager to Configure Pager Setup Pager Number and PINSetup Pagers Setup Modem Pager dialing results Enter a Pager Number Setup Pager MenuGuidelines for dialing pagers Enter a Pager PIN Number Enter Pager NUMBER40 Characters MAX Command Successful Enter Time To Perform Communications Check Enable Communications Check Select Setup System Setup System Setup System InfoSetup System Info Setup EXP Board Setup System Info Change the Password Change PasswordReset Password to the Factory Default Aaaa Change Date & Time/Automatic Daylight Saving Time Connect Battery Setup Site IDSetup Site ID Battery alarms Backup and Upload Configuration File Back Up the Configuration File Upload the Configuration File Service phone number dialing results Setup Serv Ph Num Enter Phone NumberGuidelines for dialing service phone number Setup Serv Ph Num Setup Service Phone Number Service Terminal Interface only Factory Defaults Factory DefaultsFirmware Update Service Terminal Interface only Factory Defaults System and Control Options Disconnect Initiate Remote Alarm Test Service Terminal Interface only Setup Exp Board Optional Expansion Board Setup EXP BoardExpansion Board Connected Manual Output Ctrl Clear Alarms & Logs Clear Active AlarmsClear the Alarm Log Clear the Trend Logs Clear the Event LogClear Event Log Clear Trend Log Specifications Universal Monitor Specifications Umexp Optional Expansion Board Specifications Comparison of Functions LCD and Service Terminal Interface Appendix a Service Terminal Interface Connecting to the Service Terminal Interface Steps to set up a direct or remote connectionConnection Methods Direct Connection via RS232 Create a ConnectionRemote Connection via Modem Choose COM1 Choose the computer’s modem COM1 Port Setup Set Up the COM1 Port Direct Connection Only Properties Setup Set Up the Connection’s PropertiesAscii Setup Settings tab Connect to the Service Terminal Interface Click on the file name for example, Universal Monitor.htDial button OK button Setup Menu Overview Silence Alarm and Backup Log FilesView Status Overview Main Menu For sample screens, see View Status Menus Main MenuMain Menu View Active Alarms View Active Alarms View Alarm Log View Alarm Log View Event Log View Event Log View Trend Log View Trend Log View Input & Sensor Status View Input Status View Output Status View Output Status View Pager Numbers View Pager Numbers Section A.5.1 Section A.5.2 Silence Alarm Backup Log Files Alarm Log File Back Up Alarm Log File Back Up Event Log File Backup Log Files Event Log File Back Up Trend Log Files Backup Log Files Trend Log Files Setup Menu Login MenuLogin Setup Menu Setup MenuTips on Using the Service Terminal Interface See Description Setup Input Main Board Outputs Setup Input Setup Input Expansion Board Inputs Setup Common Alarm Setup Common Alarm Setup Sensor Setup Sensor 110 Setup I-O Matrix Map Input to Output Main Board Inputs Setup I/O Matrix 112 Setup I-O Matrix Map Input to Output Expansion Board Inputs 114 Setup I-O Matrix Map Sensor to Output 116 Setup Output Main Board Outputs Setup Output Setup Output Expansion Board Outputs Setup Modem & Pagers Pager SetupSetup Modem & Pagers Pager Setup Setup Modem & Pagers Modem Setup Modem Setup Setup System Info Setup System InfoChange Password Change Date & Time Setup Site ID Backup & Upload Configuration File Backup Connect Battery Setup Service Phone Number Backup & Upload Configuration File UploadSetup Service Phone Number Firmware Update Factory Defaults Initiate Remote Alarm Test Connect Expansion Board Connect Expansion Board Override Output Main Board Outputs Override Output Override Output Expansion Board Outputs Clear Alarms & Logs Clear Alarms & Logs Clear Active AlarmsClear Alarms & Logs Clear the Alarm Log Clear Alarms & Logs Clear the Trend Logs Clear Alarms & Logs Clear the Event Log Universal Monitor default settings for inputs and outputs Appendix B Default Settings Quick Reference Guide Change Password Universal Monitor other default settings Expansion Board other default settings Expansion Board default settings for inputs and outputsPage Company Behind the Products Technical Support/ServiceLocations Asia 23F, Allied Kajima Bldg