Liebert Universal Monitor specs

Wiring and Connections - Optional Expansion Board

5.0WIRING AND CONNECTIONS - OPTIONAL EXPANSION BOARD

! CAUTION

Remove all power before installing any wiring to the Expansion Board or changing input or output connections.

! WARNING

“RISK OF ELECTRIC SHOCK” - More than one disconnect switch may be required to de-energize the equipment before servicing.

5.1Wiring Specifications

Input and output connections to the optional Expansion Board may be made in any order—it is not necessary, for example, to make all input connections before making any output connections. Use cop- per conductors only for all wiring.

Table 9	Wiring specifications - optional Expansion Board

Connection		Supported Wire Type	Maximum Wire Length			Rating

Digital		18-22 AWG Stranded & Unshielded				Dry Contact
		18 AWG* (recommended)				Dry Contact
		18 AWG* (recommended)		750 ft. (225m)		(24VDC,
Input		Non Plenum - Belden 9740		750 ft. (225m)		(24VDC,
Input		Non Plenum - Belden 9740				10 mA)
		Plenum - Belden 89740				10 mA)
		Plenum - Belden 89740

		18-22 AWG Stranded & Unshielded	18 AWG*	20 AWG	22 AWG
Digital			(recommended)	20 AWG	22 AWG
			(recommended)
		18 AWG* (recommended)				240VAC,
		18 AWG* (recommended)	@3A 50 ft. (15m)	@3A 40 ft. (12m)	@3A 25 ft. (7m)	240VAC,
Output		Non Plenum - Belden 9740	@3A 50 ft. (15m)	@3A 40 ft. (12m)	@3A 25 ft. (7m)	2A max.
		Plenum - Belden 89740	@2A 100 ft. (30m)	@2A 60 ft. (18m)	@2A 35 ft. (10m)
			@1A 200 ft. (60m)	@1A 100 ft. (30m)	@1A 75 ft. (23m)
Communication		18-22 AWG Stranded & Shielded
Communication		22 AWG* (recommended)		3000 ft. (900m)		N/A
EIA485		Non Plenum - Belden 9461		3000 ft. (900m)		N/A
EIA485		Non Plenum - Belden 9461
		Plenum - Belden 88761

24VAC Power		18-22 AWG Stranded & Shielded
24VAC Power		18 AWG* (recommended)				24VAC
Connection		18 AWG* (recommended)		150 ft. (45m)		24VAC
Connection		Non Plenum - Belden 8770		150 ft. (45m)		@0.6A
(TB1)		Non Plenum - Belden 8770				@0.6A
(TB1)		Plenum - Belden 88770
		Plenum - Belden 88770

* Recommended

25

Image 33

Liebert Universal Monitor Wiring and Connections Optional Expansion Board, Wiring specifications optional Expansion Board

Contents

Monitoring Universal MonitorPage Table of Contents Opening Screen Overview Main Menu Overview LCD Menu Overview Setup System Setup I/O Matrix Appendix B Default Settings Quick Reference Guide Appendix a Service Terminal Interface Figures Page Optional Features Methods of Viewing and Configuring the Universal MonitorAvailable Alarms Data Logs Outside Enclosure Overview Enclosure has knockouts Access slotsOn top Transformer Module Back of LCD Controller Board Universal Monitor Main board RS232 Phone Line Typical ConfigurationDigital outputs Digital inputs Controller board components Controller Board Overview Connector EIA422 Of-power jumperEIA485 connector Connector RS232 Expansion board components Optional Expansion Board Overview LED indicators summary LED Indicators Color Description Power status LED Indicators Optional Expansion BoardEIA485 status LEDs D4 yellow D5 red General status LED D3 green Typical Sequence Installation Main Board Installation ConsiderationsPacking Contents Unpacking and Preliminary Inspection Required tools Surface-Mounting the Universal MonitorMounting the Panel Bottom hole diameter Flush-Mounting the Universal Monitor Input Power Connections Small Enclosure Connect Power to the Universal Monitor VAC Output Power Connections Input Power ConnectionsTermination and Mounting Large Enclosure Connection Type Connecting the Battery Pack Troubleshooting Transformer ModuleObtaining a Replacement Battery Pack Problem Possible Solution Replacement Fuse Part Numbers Packing manifest optional Expansion Board Installation Optional Expansion Board Surface-Mounting the Optional Expansion Board Mounting Dimensions optional Expansion Board Flush-Mounting the Optional Expansion Board Pre-wired Input Power Connections Optional Expansion Board24VAC wiring red & white 24VAC input connectors AC1 & AC2 TM115 shown Wiring Specifications Wiring and Connections Main BoardWiring specifications main board Connecting Digital Inputs Connecting Digital Inputs and Digital OutputsConnecting Digital Outputs Proceeds up numbering keys are shown at right Connecting Analog Inputs Setting the Digital Output JumpersDigital output jumper settings Connecting the Analog Ground Setting the 12VDC/24VDC Analog Power Jumper EIA422 SiteScan Web Connector Connecting Common Alarm Outputs1 RS232 Connector Phone Line Connector Wiring specifications optional Expansion Board Wiring and Connections Optional Expansion Board Numbering keys Connecting Inputs and Outputs Relay is Closed On power failure NumberingKeys Setting the Digital Output DIP Switches DIP switch setting outputs wired as Normally Closed N.CDIP switch setting outputs wired as Normally Open N.O Connect EIA485 Connectors to Main Board Enable the Connection via FirmwareConnect to the Universal Monitor Guide to Universal Monitor functions Overview of Menus Opening Screen Overview Main Menu OverviewLCD Menu Overview View Status Options Active Alarms View Active AlarmsClearing Active Alarms Active Alarms Alarm Log View Alarm LogAlarm log conditions Main Menu Alarm Log Event Log View Event LogEvent Log Event log conditions View Trend Log Select a SensorView a Trend Log View Input Status Input StatusViewing Additional Input Data Output Status View Output StatusViewing Additional Output Data Digital output states Select a Pager View Pager NumbersView a Pager Number View a Pager PIN Silence Alarm Service Terminal Interface only Silence Alarm & Backup LOG Files Service Terminal Interface Back Up Log Files Service Terminal Interface only Silence Alarm & Backup Log Files Service Terminal Interface Login LoginSystem and Control Options Valid characters for data entry System & Control menu Setup System selected Login ScreenSetup System menu System & Control menu Clear Alarms&Logs selected Setup System Setup Input Setup System Overview Define Input as Alarmable or Event Change Label Name of InputDefine Input as Normally Open or Normally Closed Set Up Delay Time Set Up Alarmable Inputs in Latched or Unlatched ModeDelay Time Latched / Unlatched Change to Reset Y or Not Reset N Setup System Setup Common AlarmReset Common Alarm Setup Common Alarm Setup Sensor Setup System Setup Sensor Select a Sensor to ConfigureDefault settings analog sensor inputs Identify the Sensor as Connected Change Sensor Label NameChange Units Label Change 4 mA Value Change 20 mA ValueChange Offset Value Define Sensor as Alarmable or Event Set Up Alarmable Sensors in Latched or Unlatched ModeMessage if sensor has been defined as an event Change High Setpoint Change Low SetpointChange Low Setpoint Change High Setpoint Sensor Delay Setup System Setup I/O Matrix Set Up Mapping for a Digital InputMap Input to a Main Board Output Default mapping of digital inputs to digital outputs Default Mappings Digital Inputs to OutputsDigital input By default, mapped to digital output Map Input to Expansion Board Output Default Mappings Analog Inputs to Outputs Set Up Mapping for an Analog Sensor InputMap Sensor to Main Board Output Map Sensor to Expansion Board Output Setup System Setup Output Change Label Name of OutputDefine Main Board Output as Normally Open / Closed Set Expansion Board Output by DIP Switch Configure Main Board Output for Loss of Power Fail-SafeMessage if Expansion Board output selected Modem Setup Initialization String Setup System Setup Modem & PagersSupported Modem Settings Default Modem Settings Country codes Setup System Menu Select Modem SetupSetup Modem Menu International Dialing Enter Universal Monitor Phone Number Enable Modem Diagnostic Messages Change Modem Hang Up Delay After a CallChange Modem Dial Prefix Select a Pager to Configure Pager Setup Pager Number and PINSetup Pagers Setup Modem Pager dialing results Enter a Pager Number Setup Pager MenuGuidelines for dialing pagers Enter a Pager PIN Number Enter Pager NUMBER40 Characters MAX Command Successful Enter Time To Perform Communications Check Enable Communications Check Select Setup System Setup System Setup System InfoSetup System Info Setup EXP Board Setup System Info Change the Password Change PasswordReset Password to the Factory Default Aaaa Change Date & Time/Automatic Daylight Saving Time Connect Battery Setup Site IDSetup Site ID Battery alarms Backup and Upload Configuration File Back Up the Configuration File Upload the Configuration File Service phone number dialing results Setup Serv Ph Num Enter Phone NumberGuidelines for dialing service phone number Setup Serv Ph Num Setup Service Phone Number Service Terminal Interface only Factory Defaults Factory DefaultsFirmware Update Service Terminal Interface only Factory Defaults System and Control Options Disconnect Initiate Remote Alarm Test Service Terminal Interface only Setup Exp Board Optional Expansion Board Setup EXP BoardExpansion Board Connected Manual Output Ctrl Clear Alarms & Logs Clear Active AlarmsClear the Alarm Log Clear the Trend Logs Clear the Event LogClear Event Log Clear Trend Log Specifications Universal Monitor Specifications Umexp Optional Expansion Board Specifications Comparison of Functions LCD and Service Terminal Interface Appendix a Service Terminal Interface Connecting to the Service Terminal Interface Steps to set up a direct or remote connectionConnection Methods Direct Connection via RS232 Create a ConnectionRemote Connection via Modem Choose COM1 Choose the computer’s modem COM1 Port Setup Set Up the COM1 Port Direct Connection Only Properties Setup Set Up the Connection’s PropertiesAscii Setup Settings tab Connect to the Service Terminal Interface Click on the file name for example, Universal Monitor.htDial button OK button Setup Menu Overview Silence Alarm and Backup Log FilesView Status Overview Main Menu For sample screens, see View Status Menus Main MenuMain Menu View Active Alarms View Active Alarms View Alarm Log View Alarm Log View Event Log View Event Log View Trend Log View Trend Log View Input & Sensor Status View Input Status View Output Status View Output Status View Pager Numbers View Pager Numbers Section A.5.1 Section A.5.2 Silence Alarm Backup Log Files Alarm Log File Back Up Alarm Log File Back Up Event Log File Backup Log Files Event Log File Back Up Trend Log Files Backup Log Files Trend Log Files Setup Menu Login MenuLogin Setup Menu Setup MenuTips on Using the Service Terminal Interface See Description Setup Input Main Board Outputs Setup Input Setup Input Expansion Board Inputs Setup Common Alarm Setup Common Alarm Setup Sensor Setup Sensor 110 Setup I-O Matrix Map Input to Output Main Board Inputs Setup I/O Matrix 112 Setup I-O Matrix Map Input to Output Expansion Board Inputs 114 Setup I-O Matrix Map Sensor to Output 116 Setup Output Main Board Outputs Setup Output Setup Output Expansion Board Outputs Setup Modem & Pagers Pager SetupSetup Modem & Pagers Pager Setup Setup Modem & Pagers Modem Setup Modem Setup Setup System Info Setup System InfoChange Password Change Date & Time Setup Site ID Backup & Upload Configuration File Backup Connect Battery Setup Service Phone Number Backup & Upload Configuration File UploadSetup Service Phone Number Firmware Update Factory Defaults Initiate Remote Alarm Test Connect Expansion Board Connect Expansion Board Override Output Main Board Outputs Override Output Override Output Expansion Board Outputs Clear Alarms & Logs Clear Alarms & Logs Clear Active AlarmsClear Alarms & Logs Clear the Alarm Log Clear Alarms & Logs Clear the Trend Logs Clear Alarms & Logs Clear the Event Log Universal Monitor default settings for inputs and outputs Appendix B Default Settings Quick Reference Guide Change Password Universal Monitor other default settings Expansion Board other default settings Expansion Board default settings for inputs and outputsPage Company Behind the Products Technical Support/ServiceLocations Asia 23F, Allied Kajima Bldg