Liebert Universal Monitor user manual Setup System Setup Output, Change Label Name of Output

System and Control Options

9.7Setup System - Setup Output

The Universal Monitor has eight outputs that may be configured indi- vidually. If the optional Expansion Board is used, its additional eight digital outputs may be renamed. The outputs may have a wide variety of Liebert or other manufacturers’ equipment connected for configured responses to input alarms and events.

To configure an output:

Log In and Choose Setup System

•From the Main Menu, use the arrows ↑ ↓ to choose System and Control, then press Enter ↵ (see 9.1 - Login for help).

•Enter your password at the Login screen.

•From the System and Control Menu, use the arrows ↑ ↓ to choose Setup System, then press Enter ↵ .

Select an Output to Configure

•From the Setup System Menu, shown at right, use the arrows ↑ ↓ to choose Setup Output and press Enter ↵ .

•From the Select Output Menu, choose the output you want—for example, Output01—and press Enter ↵ .

Table 25 shows digital output features and default settings. You may change the name of any output. In addition, the Universal Monitor’s eight outputs may be defined as normally open or closed.

Use the steps following Table 25 to change the default settings for any digital output.

Table 25 Default settings - digital outputs

Feature	Default	Other Options
LABEL	OUTPUT01	Any name (up to eight
		characters)
NORM OPEN/CLOSE	NO (Normally open)	NC (Normally closed)
(Main board only)

9.7.1Change Label (Name of Output)

Each output has a default label (Output01, Output02, etc.) that you may change to a more descriptive name. The label may consist of up to eight characters (see Table 20 for valid characters).

•From the Setup Output Menu, as shown at right, use the arrows ↑ ↓ to choose Change Label for the selected output and press Enter ↵ .

•To change the output’s label, which may consist of up to eight char- acters:

•Use the arrows ↑ ↓ to choose a character.

•Press Enter ↵ to advance to the next character position.

•When finished, press Enter ↵ again.

9.7.2Define Main Board Output as Normally Open / Closed

Each output may be set up as Normally Open (NO) or Normally Closed (NC). The default setting for all output points is NO (Normally Open).

•From the Setup Output Menu, choose Change State, as shown at right, and press Enter ↵ .

•To change the normal state for this output, use the arrows ↑ ↓ to choose NO (Normally Open) or NC (Normally Closed), then press Enter ↵ .

Setup System Menu

SETUP INPUT

SETUP COMMON ALARM

SETUP SENSOR

SETUP I/O MATRIX

↑ ↓=NEXT ↵ =SELECT

>SETUP OUTPUT SETUP MODEM&PAGERS SETUP SYSTEM INFO SETUP EXP BOARD

Select Output Menu

SELECT OUTPUT

> OUTPUT01		NO
	OUTPUT02	NO
	↑ ↓=NEXT	↵ =SELECT
	OUTPUT03	NO
	OUTPUT04	NO
	OUTPUT05	NO
	OUTPUT06	NO
	OUTPUT07	NO
	OUTPUT08	NO
	OUTPUT09	NO
	OUTPUT10	NO
	OUTPUT11	NO
	OUTPUT12	NO
	OUTPUT13	NO
	OUTPUT14	NO
	OUTPUT15	NO
	OUTPUT16	NO

NOTE: OUTPUT09-OUTPUT16 for optional Expansion Board

Setup Output Menu

>CHANGE LABEL CHANGE STATE

↑ ↓=NEXT ↵ =SELECT

Change Label

CHANGE LABEL

LABEL: OUTPUT01

↑↓=SELECT ↵ =NEXT/END

Setup Output Menu

CHANGE LABEL

> CHANGE STATE

↑ ↓=NEXT ↵ =SELECT

Change State

SET TO NORMAL OPEN OR NORMAL CLOSE? NO

↑ ↓=NO/NC ↵ =END

58