Expansion Board Connected | Liebert Universal Monitor specification

System and Control Options

9.10Setup Exp Board - Optional Expansion Board

By default, the optional Expansion Board is configured as Not connected (N). After connecting power to the board and connecting it to the Universal Monitor, you must specify the Expansion Board as Connected (Y), as described in this section.

NOTE

Before specifying the Expansion Board as Connected, be sure to connect power to the board and connect it to the Universal Monitor. For more information, see:

•3.4 - Input Power Connections - Optional Expansion Board

•5.3.1 - Connect EIA485 Connectors to Main Board

To change the Expansion Board connection setting:

Log In and Choose Setup System

•From the Main Menu, use the arrows ↑ ↓ to choose System and Control, then press Enter ↵ (see 9.1 - Login for help).

•Enter your password at the Login screen.

•From the System and Control Menu, use the arrows ↑ ↓ to choose Setup System, then press Enter ↵ .

Identify the Expansion Board as Connected (Y) or Not Connected (N)

•From the Setup System Menu, shown at right, use the arrows ↑ ↓ to choose Setup Exp Board and press Enter ↵ .

•To change this setting, use the arrows ↑ ↓ to choose Y (Yes - Con- nected) or N (No - Not connected), then press Enter ↵ .

Setup System Menu

SETUP INPUT

SETUP COMMON ALARM SETUP SENSOR SETUP I/O MATRIX

↑↓=NEXT ↵ =SELECT

SETUP OUTPUT SETUP MODEM&PAGERS SETUP SYSTEM INFO

> SETUP EXP BOARD

Expansion Board Connected

IS THE EXPANSION BOARD CONNECTED? N

↑ ↓=Y/N

↵ =END

79

Image 87

Liebert Universal Monitor user manual Setup Exp Board Optional Expansion Board, Expansion Board Connected, Setup EXP Board

Contents

Monitoring Universal MonitorPage Table of Contents Opening Screen Overview Main Menu Overview LCD Menu Overview Setup System Setup I/O Matrix Appendix B Default Settings Quick Reference Guide Appendix a Service Terminal Interface Figures Page Data Logs Methods of Viewing and Configuring the Universal MonitorOptional Features Available Alarms Transformer Module Back of LCD Controller Board Enclosure has knockouts Access slotsOutside Enclosure Overview On top Digital inputs Typical ConfigurationUniversal Monitor Main board RS232 Phone Line Digital outputs Controller board components Controller Board Overview Connector RS232 Of-power jumperConnector EIA422 EIA485 connector Expansion board components Optional Expansion Board Overview LED indicators summary LED Indicators General status LED D3 green LED Indicators Optional Expansion BoardColor Description Power status EIA485 status LEDs D4 yellow D5 red Typical Sequence Unpacking and Preliminary Inspection Installation ConsiderationsInstallation Main Board Packing Contents Bottom hole diameter Surface-Mounting the Universal MonitorRequired tools Mounting the Panel Flush-Mounting the Universal Monitor Input Power Connections Small Enclosure Connect Power to the Universal Monitor Connection Type Input Power ConnectionsVAC Output Power Connections Termination and Mounting Large Enclosure Problem Possible Solution Replacement Fuse Part Numbers Troubleshooting Transformer ModuleConnecting the Battery Pack Obtaining a Replacement Battery Pack Packing manifest optional Expansion Board Installation Optional Expansion Board Surface-Mounting the Optional Expansion Board Mounting Dimensions optional Expansion Board Flush-Mounting the Optional Expansion Board TM115 shown Input Power Connections Optional Expansion BoardPre-wired 24VAC wiring red & white 24VAC input connectors AC1 & AC2 Wiring Specifications Wiring and Connections Main BoardWiring specifications main board Proceeds up numbering keys are shown at right Connecting Digital Inputs and Digital OutputsConnecting Digital Inputs Connecting Digital Outputs Connecting Analog Inputs Setting the Digital Output JumpersDigital output jumper settings Connecting the Analog Ground Setting the 12VDC/24VDC Analog Power Jumper Phone Line Connector Connecting Common Alarm OutputsEIA422 SiteScan Web Connector 1 RS232 Connector Wiring specifications optional Expansion Board Wiring and Connections Optional Expansion Board Numbering keys Connecting Inputs and Outputs Relay is Closed On power failure NumberingKeys Setting the Digital Output DIP Switches DIP switch setting outputs wired as Normally Closed N.CDIP switch setting outputs wired as Normally Open N.O Connect EIA485 Connectors to Main Board Enable the Connection via FirmwareConnect to the Universal Monitor Guide to Universal Monitor functions Overview of Menus Opening Screen Overview Main Menu OverviewLCD Menu Overview View Status Options Active Alarms View Active AlarmsActive Alarms Clearing Active Alarms Alarm Log View Alarm LogAlarm Log Alarm log conditions Main Menu Event log conditions View Event LogEvent Log Event Log View Trend Log Select a SensorView a Trend Log View Input Status Input StatusViewing Additional Input Data Digital output states View Output StatusOutput Status Viewing Additional Output Data View a Pager PIN View Pager NumbersSelect a Pager View a Pager Number Silence Alarm Service Terminal Interface only Silence Alarm & Backup LOG Files Service Terminal Interface Back Up Log Files Service Terminal Interface only Silence Alarm & Backup Log Files Service Terminal Interface Valid characters for data entry LoginLogin System and Control Options System & Control menu Clear Alarms&Logs selected Login ScreenSystem & Control menu Setup System selected Setup System menu Setup System Setup Input Setup System Overview Define Input as Alarmable or Event Change Label Name of InputDefine Input as Normally Open or Normally Closed Latched / Unlatched Set Up Alarmable Inputs in Latched or Unlatched ModeSet Up Delay Time Delay Time Setup Common Alarm Setup Sensor Setup System Setup Common AlarmChange to Reset Y or Not Reset N Reset Common Alarm Setup System Setup Sensor Select a Sensor to ConfigureDefault settings analog sensor inputs Identify the Sensor as Connected Change Sensor Label NameChange Units Label Change 4 mA Value Change 20 mA ValueChange Offset Value Define Sensor as Alarmable or Event Set Up Alarmable Sensors in Latched or Unlatched ModeMessage if sensor has been defined as an event Change High Setpoint Change Low SetpointChange High Setpoint Change Low Setpoint Sensor Delay Setup System Setup I/O Matrix Set Up Mapping for a Digital InputMap Input to a Main Board Output Map Input to Expansion Board Output Default Mappings Digital Inputs to OutputsDefault mapping of digital inputs to digital outputs Digital input By default, mapped to digital output Map Sensor to Expansion Board Output Set Up Mapping for an Analog Sensor InputDefault Mappings Analog Inputs to Outputs Map Sensor to Main Board Output Setup System Setup Output Change Label Name of OutputDefine Main Board Output as Normally Open / Closed Set Expansion Board Output by DIP Switch Configure Main Board Output for Loss of Power Fail-SafeMessage if Expansion Board output selected Default Modem Settings Setup System Setup Modem & PagersModem Setup Initialization String Supported Modem Settings International Dialing Select Modem SetupCountry codes Setup System Menu Setup Modem Menu Enter Universal Monitor Phone Number Enable Modem Diagnostic Messages Change Modem Hang Up Delay After a CallChange Modem Dial Prefix Pager dialing results Pager Setup Pager Number and PINSelect a Pager to Configure Setup Pagers Setup Modem Enter a Pager PIN Number Setup Pager MenuEnter a Pager Number Guidelines for dialing pagers Enter Pager NUMBER40 Characters MAX Command Successful Enter Time To Perform Communications Check Enable Communications Check Setup System Info Setup System Setup System InfoSelect Setup System Setup System Info Setup EXP Board Change Date & Time/Automatic Daylight Saving Time Change PasswordChange the Password Reset Password to the Factory Default Aaaa Battery alarms Setup Site IDConnect Battery Setup Site ID Backup and Upload Configuration File Back Up the Configuration File Upload the Configuration File Setup Serv Ph Num Setup Serv Ph Num Enter Phone NumberService phone number dialing results Guidelines for dialing service phone number Setup Service Phone Number Service Terminal Interface only Factory Defaults Factory DefaultsFactory Defaults Firmware Update Service Terminal Interface only System and Control Options Disconnect Initiate Remote Alarm Test Service Terminal Interface only Setup Exp Board Optional Expansion Board Setup EXP BoardExpansion Board Connected Manual Output Ctrl Clear Alarms & Logs Clear Active AlarmsClear the Alarm Log Clear Trend Log Clear the Event LogClear the Trend Logs Clear Event Log Specifications Universal Monitor Specifications Umexp Optional Expansion Board Specifications Comparison of Functions LCD and Service Terminal Interface Appendix a Service Terminal Interface Connecting to the Service Terminal Interface Steps to set up a direct or remote connectionConnection Methods Choose COM1 Choose the computer’s modem Create a ConnectionDirect Connection via RS232 Remote Connection via Modem COM1 Port Setup Set Up the COM1 Port Direct Connection Only Settings tab Set Up the Connection’s PropertiesProperties Setup Ascii Setup Connect to the Service Terminal Interface Click on the file name for example, Universal Monitor.htDial button OK button Main Menu For sample screens, see Silence Alarm and Backup Log FilesSetup Menu Overview View Status Overview View Status Menus Main MenuMain Menu View Active Alarms View Active Alarms View Alarm Log View Alarm Log View Event Log View Event Log View Trend Log View Trend Log View Input & Sensor Status View Input Status View Output Status View Output Status View Pager Numbers View Pager Numbers Section A.5.1 Section A.5.2 Silence Alarm Backup Log Files Alarm Log File Back Up Alarm Log File Back Up Event Log File Backup Log Files Event Log File Back Up Trend Log Files Backup Log Files Trend Log Files Setup Menu Login MenuLogin See Description Setup MenuSetup Menu Tips on Using the Service Terminal Interface Setup Input Main Board Outputs Setup Input Setup Input Expansion Board Inputs Setup Common Alarm Setup Common Alarm Setup Sensor Setup Sensor 110 Setup I-O Matrix Map Input to Output Main Board Inputs Setup I/O Matrix 112 Setup I-O Matrix Map Input to Output Expansion Board Inputs 114 Setup I-O Matrix Map Sensor to Output 116 Setup Output Main Board Outputs Setup Output Setup Output Expansion Board Outputs Setup Modem & Pagers Pager SetupSetup Modem & Pagers Pager Setup Setup Modem & Pagers Modem Setup Modem Setup Setup System Info Setup System InfoChange Password Change Date & Time Setup Site ID Backup & Upload Configuration File Backup Connect Battery Setup Service Phone Number Backup & Upload Configuration File UploadSetup Service Phone Number Firmware Update Factory Defaults Initiate Remote Alarm Test Connect Expansion Board Connect Expansion Board Override Output Main Board Outputs Override Output Override Output Expansion Board Outputs Clear Alarms & Logs Clear Alarms & Logs Clear Active AlarmsClear Alarms & Logs Clear the Alarm Log Clear Alarms & Logs Clear the Trend Logs Clear Alarms & Logs Clear the Event Log Universal Monitor default settings for inputs and outputs Appendix B Default Settings Quick Reference Guide Change Password Universal Monitor other default settings Expansion Board other default settings Expansion Board default settings for inputs and outputsPage Asia 23F, Allied Kajima Bldg Technical Support/ServiceCompany Behind the Products Locations