View Active Alarms | Liebert Universal Monitor instruction

View Status Options

7.1View Active Alarms

The Active Alarm screen displays all alarms that are occurring, up to a maximum of 33.

A Current Alarm screen appears automatically whenever an alarm occurs—except during setup. This screen can display only the two most recent active alarms. To view any other active alarms, use the View Active Alarms feature.

You may view active alarms at any time by using the following steps:

•From the Main Menu, use the arrows ↑ ↓to choose View Status, as shown at right, and then press Enter ↵ .

•From the View Status Menu, use the arrows ↑ ↓ to choose View Active Alarms and press Enter ↵ .

Main Menu

>VIEW STATUS SYSTEM AND CONTROL

↑ ↓=NEXT

↵ =SELECT

View Status Menu

>VIEW ACTIVE ALARMS VIEW ALARM LOG VIEW EVENT LOG VIEW TREND LOG

VIEW INPUT STATUS VIEW OUTPUT STATUS VIEW PAGER NUMBERS

7.1.1Active Alarms

The Active Alarms screen displays up to 33 records; it shows any active alarm and any Latched alarm that has not been cleared. Examples of alarms include inputs in alarm status, a low battery condition and a loss of connection to an analog input. When any alarms are present, the Active Alarms screen shows descriptive details for each alarm:

•the source of the alarm (for example, SENSOR_1 or BATTERY)

•the status of an input or output (101.0 DEG)

•a brief description of the problem (HIGH SETPOINT ALARM or CHECK BATTERY)

If there are no active alarms, the screen displays the message:

Active Alarms

> ACTIVE ALARM 33/33
SENSOR_1	101.0 DEG
HIGH SETPOINT ALARM
SENSOR_2	------ DEG
SENSOR PROBLEM
INPUT_07	ALARM
CONTACT OPEN
BATTERY
CHECK BATTERY

NO ALARMS PRESENT

Viewing Additional Screens

There may be up to 33 records of alarm data.

•To view additional records, use the arrows ↑ ↓.

•To return to the previous screen, press the ESC key.

Clearing Active Alarms

To clear all active alarms, see 9.12 - Clear Alarms & Logs. Alarm records are stored in the Alarm Log.

33

Image 41

Liebert Universal Monitor user manual View Active Alarms, Viewing Additional Screens, Clearing Active Alarms

Contents

Monitoring Universal MonitorPage Table of Contents Opening Screen Overview Main Menu Overview LCD Menu Overview Setup System Setup I/O Matrix Appendix B Default Settings Quick Reference Guide Appendix a Service Terminal Interface Figures Page Optional Features Methods of Viewing and Configuring the Universal MonitorAvailable Alarms Data Logs Outside Enclosure Overview Enclosure has knockouts Access slotsOn top Transformer Module Back of LCD Controller Board Universal Monitor Main board RS232 Phone Line Typical ConfigurationDigital outputs Digital inputs Controller board components Controller Board Overview Connector EIA422 Of-power jumperEIA485 connector Connector RS232 Expansion board components Optional Expansion Board Overview LED indicators summary LED Indicators Color Description Power status LED Indicators Optional Expansion BoardEIA485 status LEDs D4 yellow D5 red General status LED D3 green Typical Sequence Installation Main Board Installation ConsiderationsPacking Contents Unpacking and Preliminary Inspection Required tools Surface-Mounting the Universal MonitorMounting the Panel Bottom hole diameter Flush-Mounting the Universal Monitor Input Power Connections Small Enclosure Connect Power to the Universal Monitor VAC Output Power Connections Input Power ConnectionsTermination and Mounting Large Enclosure Connection Type Connecting the Battery Pack Troubleshooting Transformer ModuleObtaining a Replacement Battery Pack Problem Possible Solution Replacement Fuse Part Numbers Packing manifest optional Expansion Board Installation Optional Expansion Board Surface-Mounting the Optional Expansion Board Mounting Dimensions optional Expansion Board Flush-Mounting the Optional Expansion Board Pre-wired Input Power Connections Optional Expansion Board24VAC wiring red & white 24VAC input connectors AC1 & AC2 TM115 shown Wiring specifications main board Wiring SpecificationsWiring and Connections Main Board Connecting Digital Inputs Connecting Digital Inputs and Digital OutputsConnecting Digital Outputs Proceeds up numbering keys are shown at right Digital output jumper settings Connecting Analog InputsSetting the Digital Output Jumpers Connecting the Analog Ground Setting the 12VDC/24VDC Analog Power Jumper EIA422 SiteScan Web Connector Connecting Common Alarm Outputs1 RS232 Connector Phone Line Connector Wiring specifications optional Expansion Board Wiring and Connections Optional Expansion Board Numbering keys Connecting Inputs and Outputs Keys Relay is Closed On power failureNumbering DIP switch setting outputs wired as Normally Open N.O Setting the Digital Output DIP SwitchesDIP switch setting outputs wired as Normally Closed N.C Connect to the Universal Monitor Connect EIA485 Connectors to Main BoardEnable the Connection via Firmware Guide to Universal Monitor functions Overview of Menus LCD Menu Overview Opening Screen OverviewMain Menu Overview View Status Options Active Alarms View Active AlarmsClearing Active Alarms Active Alarms Alarm Log View Alarm LogAlarm log conditions Main Menu Alarm Log Event Log View Event LogEvent Log Event log conditions View a Trend Log View Trend LogSelect a Sensor Viewing Additional Input Data View Input StatusInput Status Output Status View Output StatusViewing Additional Output Data Digital output states Select a Pager View Pager NumbersView a Pager Number View a Pager PIN Silence Alarm Service Terminal Interface only Silence Alarm & Backup LOG Files Service Terminal Interface Back Up Log Files Service Terminal Interface only Silence Alarm & Backup Log Files Service Terminal Interface Login LoginSystem and Control Options Valid characters for data entry System & Control menu Setup System selected Login ScreenSetup System menu System & Control menu Clear Alarms&Logs selected Setup System Setup Input Setup System Overview Define Input as Normally Open or Normally Closed Define Input as Alarmable or EventChange Label Name of Input Set Up Delay Time Set Up Alarmable Inputs in Latched or Unlatched ModeDelay Time Latched / Unlatched Change to Reset Y or Not Reset N Setup System Setup Common AlarmReset Common Alarm Setup Common Alarm Setup Sensor Default settings analog sensor inputs Setup System Setup SensorSelect a Sensor to Configure Change Units Label Identify the Sensor as ConnectedChange Sensor Label Name Change Offset Value Change 4 mA ValueChange 20 mA Value Message if sensor has been defined as an event Define Sensor as Alarmable or EventSet Up Alarmable Sensors in Latched or Unlatched Mode Change High Setpoint Change Low SetpointChange Low Setpoint Change High Setpoint Sensor Delay Map Input to a Main Board Output Setup System Setup I/O MatrixSet Up Mapping for a Digital Input Default mapping of digital inputs to digital outputs Default Mappings Digital Inputs to OutputsDigital input By default, mapped to digital output Map Input to Expansion Board Output Default Mappings Analog Inputs to Outputs Set Up Mapping for an Analog Sensor InputMap Sensor to Main Board Output Map Sensor to Expansion Board Output Define Main Board Output as Normally Open / Closed Setup System Setup OutputChange Label Name of Output Message if Expansion Board output selected Set Expansion Board Output by DIP SwitchConfigure Main Board Output for Loss of Power Fail-Safe Modem Setup Initialization String Setup System Setup Modem & PagersSupported Modem Settings Default Modem Settings Country codes Setup System Menu Select Modem SetupSetup Modem Menu International Dialing Enter Universal Monitor Phone Number Change Modem Dial Prefix Enable Modem Diagnostic MessagesChange Modem Hang Up Delay After a Call Select a Pager to Configure Pager Setup Pager Number and PINSetup Pagers Setup Modem Pager dialing results Enter a Pager Number Setup Pager MenuGuidelines for dialing pagers Enter a Pager PIN Number Enter Pager NUMBER40 Characters MAX Command Successful Enter Time To Perform Communications Check Enable Communications Check Select Setup System Setup System Setup System InfoSetup System Info Setup EXP Board Setup System Info Change the Password Change PasswordReset Password to the Factory Default Aaaa Change Date & Time/Automatic Daylight Saving Time Connect Battery Setup Site IDSetup Site ID Battery alarms Backup and Upload Configuration File Back Up the Configuration File Upload the Configuration File Service phone number dialing results Setup Serv Ph Num Enter Phone NumberGuidelines for dialing service phone number Setup Serv Ph Num Setup Service Phone Number Service Terminal Interface only Factory Defaults Factory DefaultsFirmware Update Service Terminal Interface only Factory Defaults System and Control Options Disconnect Initiate Remote Alarm Test Service Terminal Interface only Expansion Board Connected Setup Exp Board Optional Expansion BoardSetup EXP Board Manual Output Ctrl Clear the Alarm Log Clear Alarms & LogsClear Active Alarms Clear the Trend Logs Clear the Event LogClear Event Log Clear Trend Log Specifications Universal Monitor Specifications Umexp Optional Expansion Board Specifications Comparison of Functions LCD and Service Terminal Interface Appendix a Service Terminal Interface Connection Methods Connecting to the Service Terminal InterfaceSteps to set up a direct or remote connection Direct Connection via RS232 Create a ConnectionRemote Connection via Modem Choose COM1 Choose the computer’s modem COM1 Port Setup Set Up the COM1 Port Direct Connection Only Properties Setup Set Up the Connection’s PropertiesAscii Setup Settings tab Dial button OK button Connect to the Service Terminal InterfaceClick on the file name for example, Universal Monitor.ht Setup Menu Overview Silence Alarm and Backup Log FilesView Status Overview Main Menu For sample screens, see Main Menu View Status MenusMain Menu View Active Alarms View Active Alarms View Alarm Log View Alarm Log View Event Log View Event Log View Trend Log View Trend Log View Input & Sensor Status View Input Status View Output Status View Output Status View Pager Numbers View Pager Numbers Section A.5.1 Section A.5.2 Silence Alarm Backup Log Files Alarm Log File Back Up Alarm Log File Back Up Event Log File Backup Log Files Event Log File Back Up Trend Log Files Backup Log Files Trend Log Files Login Setup MenuLogin Menu Setup Menu Setup MenuTips on Using the Service Terminal Interface See Description Setup Input Main Board Outputs Setup Input Setup Input Expansion Board Inputs Setup Common Alarm Setup Common Alarm Setup Sensor Setup Sensor 110 Setup I-O Matrix Map Input to Output Main Board Inputs Setup I/O Matrix 112 Setup I-O Matrix Map Input to Output Expansion Board Inputs 114 Setup I-O Matrix Map Sensor to Output 116 Setup Output Main Board Outputs Setup Output Setup Output Expansion Board Outputs Setup Modem & Pagers Pager Setup Setup Modem & PagersPager Setup Setup Modem & Pagers Modem Setup Modem Setup Change Password Setup System InfoSetup System Info Change Date & Time Setup Site ID Backup & Upload Configuration File Backup Connect Battery Setup Service Phone Number Setup Service Phone NumberBackup & Upload Configuration File Upload Firmware Update Factory Defaults Initiate Remote Alarm Test Connect Expansion Board Connect Expansion Board Override Output Main Board Outputs Override Output Override Output Expansion Board Outputs Clear Alarms & Logs Clear the Alarm Log Clear Alarms & LogsClear Alarms & Logs Clear Active Alarms Clear Alarms & Logs Clear the Trend Logs Clear Alarms & Logs Clear the Event Log Universal Monitor default settings for inputs and outputs Appendix B Default Settings Quick Reference Guide Change Password Universal Monitor other default settings Expansion Board other default settings Expansion Board default settings for inputs and outputsPage Company Behind the Products Technical Support/ServiceLocations Asia 23F, Allied Kajima Bldg