Quatech DS-102 user manual Port Address IRQ Enabled ?

Page 8

II.INSTALLATION

If the default address and interrupt settings are sufficient, the DS-102 can be quickly installed and put to use. The factory defaults are listed in Figure 1.

PORT

ADDRESS

IRQ

ENABLED ?

 

 

 

 

 

Serial 1

3F8 hex

(COM1)

4

YES

 

 

 

 

 

Serial 2

2F8 hex

(COM2)

3

YES

 

 

 

 

 

Figure 1 --- Default address and IRQ settings for DS-102

The serial port outputs on the DS-102 are shielded D-9 connectors. Serial 1 is available on available on CN2.

CN1 and CN2, which are CN1 and Serial 2 is

1.If the default settings are correct, skip to step 2, otherwise refer to sections III and IV of this document for detailed information on how to set the address and IRQ level for each port, and for how to disable or enable each port.

2.Turn off the power of the computer system in which the DS-102 is to be installed.

3.Remove the system cover according to the instructions provided by the computer manufacturer.

4.Install the DS-102 in any vacant expansion slot. The board should be secured by installing the Option Retaining Bracket (ORB) screw.

5.Replace the system cover according to the instructions provided by the computer manufacturer.

6.Attach and secure the D-9 connectors to the desired equipment.

2

Quatech DS-102 User's Manual

Page 7 Page 9
Image 8
Page 7 Page 9
Contents DS-102 Page IV. Setting Interrupt Levels Irqs VII. Specifications VIII. TroubleshootingTable of Contents External Connections VI. Serial Port Functional DescriptionPage Date of Purchase Model Number Page General Information Port Address IRQ Enabled ? Diagram of DS-102 Setting the address Examination of a serial port base addressSerial 1 uses SW1 Serial 2 uses SW2 Enabling or disabling ports Recommended addresses for serial portsThis page intentionally left blank Serial Interrupt Sharing Channel Connection Interrupt OperationExternal Connections J7 -- Serial J8 -- Serial DS-102 connector definitions for RS-232-C This page intentionally left blank VI. Serial Port Functional Description Accessing the Serial Port registers DlabInterrupt Enable Register Interrupt Identification RegisterInterrupt Identification Register bit definitions Fifo Control Register 16550 only RXT0Line Control Register Stkp EPS PEN ParityModem Control Register Are being usedLine Status Register Line Status Register bit definitionsModem Status Register Scratchpad RegisterFifo Interrupt Mode Operation 16550 Uart only When the receiver Fifo and receiver interrupts are enabledFifo polled mode operation 16550 Uart only Factory default Baud Rate Selection026 VII. Specifications 16450 16550 optionalComputer will not boot up

DS-102 specifications

Quatech DS-102 is a prominent device in the realm of serial device servers, designed to facilitate seamless communication between Ethernet networks and serial devices. This robust solution caters to various industries, including manufacturing, telecommunications, and data center operations, where reliable and efficient data transmission is critical.

A key feature of the Quatech DS-102 is its dual-port architecture, which allows users to connect two serial devices simultaneously. This capability is particularly advantageous in scenarios where multiple connections are necessary, enabling cost savings and simplified management. Supporting a wide range of serial protocols, including RS-232, RS-422, and RS-485, the DS-102 ensures compatibility with a diverse array of equipment.

The DS-102 employs advanced technology to ensure reliable performance. It utilizes a potent ARM-based processor that enhances data handling and decreases latency. Additionally, the device features embedded firmware that supports TCP/IP protocol stacks. This integration is pivotal for enabling remote access and management of serial devices, significantly improving operational efficiency.

One of the standout characteristics of the Quatech DS-102 is its ease of installation and configuration. The device is designed to be user-friendly, enabling quick deployment in various environments. The inclusion of a web-based configuration interface simplifies network settings and device management, providing users with intuitive access to essential functions.

Robust security protocols are also at the forefront of the DS-102's design. It supports TLS/SSL encryption to secure data transmission, ensuring that sensitive information remains protected during communication. The device is built with reliability in mind, featuring durable hardware that withstands industrial conditions, further enhancing its appeal for demanding applications.

In terms of flexibility, the Quatech DS-102 can be integrated with various operating systems, including Windows, Linux, and Mac OS, making it versatile for a range of technical environments. Its compatibility with popular software applications further streamlines operations, allowing for easy incorporation into existing systems.

Overall, the Quatech DS-102 stands out as a powerful solution for serial-to-Ethernet communication. With its dual-port capability, advanced technology, user-friendly configuration, and robust security features, it represents an ideal choice for businesses seeking to enhance their data management capabilities. As organizations continue to embrace IoT and automation, the DS-102 is well-positioned to play a vital role in connecting the legacy serial devices with modern Ethernet networks seamlessly.
Top Page Image Contents