Patton electronic 3125 manual Precautions, Typographical conventions used in this document

Page 12

About this guide

Model 3125 RAS Getting Started Guide

 

 

Precautions

Notes and cautions, which have the following meanings, are used throughout this guide to help you become aware of potential RAS problems:

Note Calls attention to important information.

The shock hazard symbol and WARNING heading indicate a potential electric shock hazard. Strictly follow the warning instructions to avoid injury caused by electric shock.

The alert symbol and WARNING heading indicate a potential safety hazard.

Strictly follow the warning instructions to avoid personal injury.

The shock hazard symbol and CAUTION heading indicate a potential electric shock hazard. Strictly fol- low the instructions to avoid property damage caused by electric shock.

The alert symbol and CAUTION heading indicate a potential hazard. Strictly follow the instructions to avoid property damage.

Typographical conventions used in this document

This section describes the typographical conventions and terms used in this guide.

General conventions

The procedures described in this manual use the following text conventions:

 

Table 1. General conventions

 

 

Convention

Meaning

 

 

Futura bold type

Indicates the names of menu bar options.

 

 

Italicized Futura type

Indicates the names of options on pull-down menus.

 

 

Futura type

Indicates the names of fields or windows.

 

 

Garamond bold type

Indicates the names of command buttons that execute an

 

action.

 

 

< >

Angle brackets indicate function and keyboard keys, such

 

as <SHIFT>, <CTRL>, <C>, and so on.

 

 

Are you ready?

All system messages and prompts appear in the Courier

 

font as the system would display them.

 

 

% dir *.*

Bold Courier font indicates where the operator must type a

 

response or command

 

 

12

Image 12
Contents Remote Access Server RAS Patton Electronics Company, Inc Contents Operation and shutdown Contents Contents Model 3125 RAS Getting Started Guide Radio and TV Interference Industry Canada NoticeFCC Information Facility Service Network Interface Code Connection FCC Part 68 Compliance Statement Service CE NoticeCompliance Information Model 3125 RAS Getting Started Guide Audience StructurePrecautions Typographical conventions used in this documentGeneral conventions Mouse conventions About this guide Model 3125 RAS Getting Started Guide Chapter contents IntroductionModel 3125 Remote Access Server overview Patton 2U, 4U, and 6U cPCI platforms Hardware overview WANSignaling Power systemTemperature ModemsPhysical dimensions RC physical dimensionsManagement services SecurityLED display RC status LEDsApprovals Software overview Software overviewHardware installation Introduction Unpacking the Model 3125 RASMaterials and Tools Required Model 3125 installation Installing the 3125TM Transition ModuleReleasing a injection/ejection handle RC and 3125TM installation diagram Installing the 3125RC Resource Card Securing the captive fastenersCable installation Connecting the Ethernet portsConnecting the EIA-561 RS-232 configuration port Straight-through RJ-45-to-RJ-45 Ethernet cable diagramCompleting the hardware installation Connecting to the T1/E1/PRI WAN portsCompleting the hardware installation Configuring the RAS for operation Configuration prerequisites Preparing the RAS for configurationConfigure the COM port settings as shown in figure COM properties Login window Opening the RAS Web Administration Pages Configuring the RAS with a Web browserHome Home page overview Home page window panesImmediate Actions buttons Configuring simple authentication No ValidationAuthentication Configuration window Static UserConfiguring dial-in user information Static User Identification windowClick on Modify. The Modify Dial-In window appears see figure Configuring the default gateway Modify Dial-In window, Domain Name Server sectionConfiguring line settings and signaling for E1 T1/E1 Link Activity windowConfiguring the line settings Pinout for loopback to test WAN portSetting the line signaling for an E1/PRI Isdn line Setting the line signaling for an E1/R2 lineMFR Version 2 Modify window Configuring line settings and signaling for T1 Channel assignmentSetting the line signaling for an ISDN/PRI line Setting the line signaling for a robbed-bit T1 lineSaving your configuration Import/Export main window Completing the installation Completing the installation Operation and shutdown Activating the RAS De-activating the RASOperation and shutdown De-activating the RAS Contacting Patton for assistance Warranty coverage Out-of-warranty serviceContact information Returns for creditReturn for credit policy RMA numbersShipping instructions