Patton electronic manual Model 3125 installation, Installing the 3125TM Transition Module

Page 27

Model 3125 RAS Getting Started Guide

2 • Hardware installation

 

 

Model 3125 installation

The resource and transition modules can easily be damaged by electrostatic discharge (ESD) resulting from the build-up of electri- cal potential on clothing and other materials.

To avid damaging the 3125 modules, perform the following safety and ESD preventive measures:

•Attach a ground strap to your wrist when connecting, discon- necting, or handling the modles. Connect the other end of the strap to a grounded surface.

•Keep the module in anti-static bags until they are needed.

•Remove a board from its anti-static bag only after you are cor- rectly grounded by a ground strap.

•Place the modules only on an anti-static mat. Do not place boards on top of an anti-static bag unless the outside of the bag also provides anti-static protection.

Verify that the chassis rack is properly grounded before installing the Model3125. An adequate ground can be achieved by con- necting a #10 AWG ground wire between the chassis rack ground stud and one of the following ground sources:

•The building ground rod (generally located at the site’s main service entrance)

•A sprinkler pipe

•A cold water pipe

•Building structural steel

Installing the 3125TM Transition Module

1.If necessary, refer to the instructions in your chassis user manual to remove any outer covers so you can access the cPCI rack card cages.

2.If there is not a slot filler panel installed, go to step 3. Otherwise, remove the two screws (located at the top of the filler panel and at the bottom) that secure the panel to the card cage.

3.Remove the 3125TM Transition Module from its anti-static bag.

Note Be sure to wear the anti-static strap to prevent electrostatic damage to the module.

Note The module should be installed as close as possible to the termination jack provided by the Telco. The location should be well ventilated. Do not block the chassis rack cooling vents.

Model 3125 installation

27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Remote Access Server RAS Patton Electronics Company, Inc Contents Operation and shutdown Contents Contents Model 3125 RAS Getting Started Guide Radio and TV Interference Industry Canada NoticeFCC Information FCC Part 68 Compliance Statement Facility Service Network Interface Code ConnectionCE Notice ServiceCompliance Information Model 3125 RAS Getting Started Guide Structure AudiencePrecautions Typographical conventions used in this documentGeneral conventions Mouse conventions About this guide Model 3125 RAS Getting Started Guide Introduction Chapter contentsModel 3125 Remote Access Server overview Patton 2U, 4U, and 6U cPCI platforms WAN Hardware overviewModems SignalingPower system TemperatureRC physical dimensions Physical dimensionsSecurity Management servicesRC status LEDs LED displayApprovals Software overview Software overviewHardware installation Introduction Unpacking the Model 3125 RASMaterials and Tools Required Installing the 3125TM Transition Module Model 3125 installationReleasing a injection/ejection handle RC and 3125TM installation diagram Securing the captive fasteners Installing the 3125RC Resource CardConnecting the Ethernet ports Cable installationStraight-through RJ-45-to-RJ-45 Ethernet cable diagram Connecting the EIA-561 RS-232 configuration portConnecting to the T1/E1/PRI WAN ports Completing the hardware installationCompleting the hardware installation Configuring the RAS for operation Preparing the RAS for configuration Configuration prerequisitesConfigure the COM port settings as shown in figure COM properties Login window Configuring the RAS with a Web browser Opening the RAS Web Administration PagesHome Home page window panes Home page overviewImmediate Actions buttons No Validation Configuring simple authenticationStatic User Authentication Configuration windowStatic User Identification window Configuring dial-in user informationClick on Modify. The Modify Dial-In window appears see figure Modify Dial-In window, Domain Name Server section Configuring the default gatewayT1/E1 Link Activity window Configuring line settings and signaling for E1Pinout for loopback to test WAN port Configuring the line settingsSetting the line signaling for an E1/R2 line Setting the line signaling for an E1/PRI Isdn lineMFR Version 2 Modify window Channel assignment Configuring line settings and signaling for T1Setting the line signaling for a robbed-bit T1 line Setting the line signaling for an ISDN/PRI lineSaving your configuration Import/Export main window Completing the installation Completing the installation Operation and shutdown De-activating the RAS Activating the RASOperation and shutdown De-activating the RAS Contacting Patton for assistance Returns for credit Warranty coverageOut-of-warranty service Contact informationReturn for credit policy RMA numbersShipping instructions

3125 specifications

The Patton Electronics 3125 is a versatile, high-performance device designed for a variety of communication applications. Known for its durability and reliability, this product has made a name for itself in the realm of network connectivity and data communication.

One of the standout features of the 3125 is its support for both T1 and E1 serial data connections. This flexibility allows users to adapt the device to different network environments, making it suitable for various applications ranging from remote access to integrating legacy systems with modern networks. The device supports frame relay and PPP protocols, which are critical for ensuring efficient data transfer across networks.

The Patton 3125 is equipped with advanced technologies that enhance its functionality. For instance, it incorporates an intelligent line monitoring feature, which helps identify and troubleshoot line faults automatically. This capability can minimize downtime, offering users a more reliable communication experience and reducing the need for on-site maintenance.

Another significant characteristic of the 3125 is its built-in network interface card (NIC) support, which allows seamless integration with IP networks. This feature is particularly valuable for businesses looking to modernize their infrastructure without completely overhauling existing systems. Furthermore, the device supports various signaling protocols, including CAS, NI1, and NI2, which facilitates compatibility with different telecom services.

Additionally, the Patton 3125 comes equipped with a user-friendly web-based interface, making configuration and management straightforward. This feature is particularly beneficial for network administrators, allowing them to monitor performance and adjust settings remotely. The device also supports SNMP for enhanced network management capabilities, further streamlining operational efficiency.

In terms of physical characteristics, the Patton 3125 is built to withstand challenging environments. Its robust casing ensures durability, and it features various mounting options for easy installation in different settings, whether in a data center or an office environment.

Overall, the Patton Electronics 3125 stands out for its combination of flexibility, advanced technology, and ease of use, making it a valuable asset for organizations seeking reliable communication solutions. Whether connecting legacy systems or enabling high-speed data transfer, the 3125 meets the demanding needs of today’s network landscape.
Top Page Image Contents