Patton electronic 2800 user manual Configuring the keep-alive interval

Page 49

OnSite 2800 Series User Manual

4 • Serial port configuration

 

 

2800(cfg)#port serial 0 0 2800(prt-ser)[0/0]#framerelay 2800(frm-rel)[0/0]#lmi-type ansi

Configuring the keep-alive interval

A keep-alive interval must be set to configure the LMI. By default, this interval is 10 seconds and, according to the LMI protocol, must be less than the corresponding interval on the switch. The keep-alive interval in sec- onds, which is represented by number, has to be in the range from 1 to 3600.

This procedure describes how to set the keep-alive interval

Mode: Frame Relay

Step

Command

Purpose

 

 

 

1

node(frm-rel)[slot/port]#keepalive number

Sets the LMI keep-alive interval

 

 

 

To disable keep-alives on networks that do not utilize LMI, use the no keepalive interface configuration command.

Example: Configuring the keep-alive interval

The following example sets the keepalive interval to 10 seconds for Frame Relay over the serial interface on slot 0 and port 0 of an OnSite router.

2800(cfg)#port serial 0 0 2800(prt-ser)[0/0]#framerelay 2800(frm-rel)[0/0]#keepalive 10

Entering Frame Relay PVC configuration mode

The permanent virtual circuit (PVC) is a virtual circuit that is permanently established. PVCs save bandwidth associ- ated with circuit establishment and tear down in situations where certain virtual circuits must exist all the time.

The Frame Relay network provides a number of virtual circuits that form the basis for connections between stations attached to the same Frame Relay network.

The resulting set of interconnected devices forms a private Frame Relay group, which may be either fully inter- connected with a complete mesh of virtual circuits, or only partially interconnected.

In either case, each virtual circuit is uniquely identified at each Frame Relay interface by a Data Link Connection Identifier (DLCI). In most circumstances, DLCIs have strictly local significance at each Frame Relay interface.

Assigning a DLCI to a specified Frame Relay sub interface on the OnSite is done in the PVC configuration mode. The DLCI has to be in the range from 1 to 1022.

Note A maximum of eight PVCs can be defined.

This procedure describes how to enter the PVC configuration.

Serial port configuration task list

49

Image 49
Contents Managed VPN Router Mailsupport@patton.com Summary Table of Contents Table of Contents Getting started with the OnSite Managed VPN Router VPN configuration LEDs status and monitoring 112 Cabling 124 OnSite 2800 Series factory configuration 132 List of Figures List of Tables Audience About this guideStructure Impaired functioning PrecautionsSafety when working with electricity General observations General conventions Typographical conventions used in this documentGeneral information Chapter contentsOnSite Managed VPN Router 2805 shown OnSite Model 2800 Series overviewOnSite 2800 Series model codes OnSite 2800 Series detailed descriptionDMZ Model code extensions OnSite 2800 Series power input connectorsOnSite 2800 Series rear-panel ports are described in table Ports descriptionsApplications overview Corporate multi-function virtual private network Corporate multi-function virtual private networkGeneral information Hardware installation Create a network diagram see section Network information on Planning the installationInstallation checklist Site log Power sourceNetwork information IP related informationConnecting cables Installing the VPN routerInstalling the Ethernet cable Location and mounting requirementsConnecting an OnSite 2800 Series device to a hub Installing the serial WAN cableDCD Hardware installation Rear panel of 2803K/EUI Rear panel of 2803K/UI Pins not listed are not usedPower connector location on rear panel Connecting to external power sourceUI and EUI power supplies automatically adjust to accept an Getting started with the OnSite Managed VPN Router Introduction Configure IP addressPower connection and default configuration Configure IP addressAll Ethernet interfaces are activated upon power-up Terminal emulation program settings 9600 bps No parity BitSelect the context IP mode to configure an IP interface LoginStop bit No flow control Changing the IP addressConnect the OnSite VPN Router to the network Load configurationRespectively from the host ping Load configuration Serial port configuration Disabling an interface Serial port configuration task listEnabling an interface Example Configuring the serial encapsulation type Configuring the encapsulation for Frame RelayPort Configuring the LMI type Enter Frame Relay modeEntering Frame Relay PVC configuration mode Configuring the keep-alive intervalBinding the Frame Relay PVC to IP interface Configuring the PVC encapsulation typeMode PVC Disabling a Frame Relay PVC Enabling a Frame Relay PVCCRC Displaying serial port informationDlci Displaying Frame Relay informationIntegrated service access Port Configure the serial interface settingsCheck that the Frame Relay settings are correct Configure the introduced PVCsT1/E1 port configuration Enable/Disable T1/E1 port T1/E1 port configuration task listConfiguring T1/E1 port-type Mode port e1t1 slot portConfiguring T1/E1 clock-mode Configuring T1/E1 line-codeConfiguring T1/E1 line-build-out T1 only Configuring T1/E1 framingConfiguring T1/E1 used-connector E1 only Name prt-e1t1 slot/port# framingConfiguring T1/E1 LOS threshold Configuring T1/E1 application modeConfiguring T1/E1 encapsulation Default short-haulConfiguring Channel-Group Timeslots Be used Mode port e1t1 slot portMode channel-group group-name Configuring Channel-Group EncapsulationConfiguring Hdlc Encapsulation Configuring Hdlc CRC-TypeT1/E1 Configuration Examples Default no encapsulationExample 1 Frame Relay without a channel-group Example 3 PPP without a channel-group Example 2 Framerelay with a channel-groupExample 4 PPP with a channel-group VPN configuration Encryption AuthenticationTransport and tunnel modes VPN configuration task listCreating an IPsec transformation profile Creating an IPsec policy profile Procedure To create an IPsec policy profileNodecfg#profile ipsec-policy-man Creating/modifying an outgoing ACL profile for IPsec Displaying IPsec configuration information Configuration of an IP interface and the IP router for IPsecExample Display IPsec policy profiles Example Display IPsec transformation profilesDebugging IPsec Example IPsec Debug OutputOnSite configuration Sample configurationsIPsec tunnel, DES encryption Cisco router configuration Cisco router configuration VPN configuration Access control list configuration What access lists do About access control listsWhy you should configure access lists Features of access control lists When to configure access listsMapping out the goals of the access control list Access control list configuration task listNodepf-acl name#permit ip src src-wildcard any Src-wildcard Where the syntax isType type type type code code cos group Nodepf-acl name#permit icmp src src-wildcard anyNodepf-acl name#deny icmp src src-wildcard Any host src dest dest-wildcard any host destMsg name Where the syntax is as followingCard any host src eq port gt port lt port range Nodepf-acl name#permit tcp udp sctp src src-wildPort lt port range from to cos group cos-rtp group Nodepf-acl name#deny tcp udp sctp src srcGroup-data Where the syntax is Displaying an access control list profile Unbind an access control list profile from an interfaceDebugging an access control list profile Control list profile shall be debugged Denying a specific subnet ExamplesLink scheduler configuration Configuring access control lists Using traffic classes Configuring quality of service QoSApplying scheduling at the bottleneck Introduction to Scheduling Weighted fair queuing WFQPriority Burst tolerant shaping or wfq ShapingHierarchy Quick references Setting the modem rateSome explanations Command cross reference Link scheduler configuration task listPacket classification Defining the access control list profileScenario with Web server regarded as a single source host Creating an access control listNodecfg#profile acl name Creating a service policy profileNodepf-acl name#permit ip host ip-address any traffic-class Nodepf-acl name#permit ip any anyStructure of a Service-Policy Profile Specifying the handling of traffic-classes Defining fair queuing weightDefining the bit-rate Specifying the type-of-service TOS fieldDefining absolute priority Defining the maximum queue lengthSpecifying the precedence field Specifying differentiated services codepoint Dscp markingNodesrc name#set ip tos value Nodesrc name#set ip precedence valueNodesrc name#set ip dscp value Specifying layer 2 markingNodesrc name#set layer2 cos value Discarding Excess Load Defining random early detectionNodesrc name#random-detect burst-tolerance Nodeif-ip if-name#use profile service Devoting the service policy profile to an interfacePolicy name in out Displaying link arbitration status Enable statistics gatheringDisplaying link scheduling profile information Values defining detail of the queuing statistics LEDs status and monitoring Status LEDs Contacting Patton for assistance Contact information Warranty coveragePatton Support Headquarters in the USA Returns for credit Out-of-warranty serviceReturn for credit policy RMA numbersAppendix a Compliance information Compliance SafetyRadio and TV Interference FCC Part CE Declaration of ConformityFCC Part 68 Acta Statement Model 2803 only Authorized European RepresentativeIndustry Canada Notice Model 2803 only Appendix B Specifications Sync serial interface Ethernet interfacesT1/E1 interface Model 2803 only PPP supportDimensions IP servicesManagement Operating environmentInternal power supply 100-240 VAC, 50/60 Hz, 200 mA Power supplyInternal AC version Appendix C Cabling Serial console Connecting a serial terminalEthernet cross-over Ethernet 10Base-T and 100Base-TEthernet straight-through Appendix D Port pin-outs EIA-561 RJ-45 8-pin port RS-232 Console Port Console port, RJ-45, EIA-561 RS-232Sync serial port Ethernet 10Base-T and 100Base-T portEthernet ports are auto-detect MDI-X Serial port21 Female DB-15 connector Appendix E OnSite 2800 Series factory configuration OnSite 2800 Series factory configuration Appendix F Installation checklist Installation checklist
Related manuals
Manual 8 pages 44.23 Kb