Patton electronic 2800 user manual T1/E1 port configuration task list, Enable/Disable T1/E1 port

Page 59

OnSite 2800 Series User Manual

5 • T1/E1 port configuration

 

 

Introduction

This chapter provides an overview of the T1/E1 WAN port, their characteristics and describes the configura- tion tasks.

The model 2803 has a T1/E1 WAN port on the rear panel of the unit. The T1 version (Model 2803T) has an RJ-48C connector, and the E1 version (Model 2803K) offers the user connectivity via either the RJ-48C or dual coaxial connectors. Both models can be configured for T1 or E1 operation.

The configurable parameters for the T1/E1 port are type (T1 or E1), clock mode (or source) (master or slave), line code (AMI, HDB3, or B8ZS), framing (CRC-4, ESF, or unframed), line-build-out (for T1 only) and encapsulation (channelized or HDLC).

A further feature is the creation and configuration of channel-groups.

T1/E1 port configuration task list

This section describes the configuration tasks for the T1/E1 port.

Enable/Disable T1/E1 port

Configuring the T1/E1 port type

Configuring T1/E1 clock mode

Configuring T1/E1 line code

Configuring T1/E1 framing

Configuring T1 line build out (LBO) (T1 only)

Configuring E1 impedance/connector

Configuring T1/E1 application mode

Configuring T1/E1 LOS threshold

Configuring T1/E1 encapsulation

Create a Channel-Group

Configuring channel-group timeslots

Configuring channel-group encapsulation

Entering HDLC configuration mode

Configuration HDLC CRC-type

Configuring HDLC encapsulation

Enable/Disable T1/E1 port

By default, the T1/E1 port is disabled. The following command is used for enabling or disabling it.

Introduction

59

Image 59
Contents Managed VPN Router Mailsupport@patton.com Summary Table of Contents Table of Contents Getting started with the OnSite Managed VPN Router VPN configuration LEDs status and monitoring 112 Cabling 124 OnSite 2800 Series factory configuration 132 List of Figures List of Tables Structure About this guideAudience Impaired functioning PrecautionsSafety when working with electricity General observations General conventions Typographical conventions used in this documentGeneral information Chapter contentsOnSite Managed VPN Router 2805 shown OnSite Model 2800 Series overviewOnSite 2800 Series model codes OnSite 2800 Series detailed descriptionDMZ Model code extensions OnSite 2800 Series power input connectorsOnSite 2800 Series rear-panel ports are described in table Ports descriptionsApplications overview Corporate multi-function virtual private network Corporate multi-function virtual private networkGeneral information Hardware installation Create a network diagram see section Network information on Planning the installationInstallation checklist IP related information Power sourceSite log Network informationLocation and mounting requirements Installing the VPN routerConnecting cables Installing the Ethernet cableConnecting an OnSite 2800 Series device to a hub Installing the serial WAN cableDCD Hardware installation Rear panel of 2803K/EUI Rear panel of 2803K/UI Pins not listed are not usedPower connector location on rear panel Connecting to external power sourceUI and EUI power supplies automatically adjust to accept an Getting started with the OnSite Managed VPN Router Introduction Configure IP addressTerminal emulation program settings 9600 bps No parity Bit Configure IP addressPower connection and default configuration All Ethernet interfaces are activated upon power-upChanging the IP address LoginSelect the context IP mode to configure an IP interface Stop bit No flow controlRespectively from the host ping Load configurationConnect the OnSite VPN Router to the network Load configuration Serial port configuration Disabling an interface Serial port configuration task listEnabling an interface Port Configuring the encapsulation for Frame RelayExample Configuring the serial encapsulation type Configuring the LMI type Enter Frame Relay modeEntering Frame Relay PVC configuration mode Configuring the keep-alive intervalBinding the Frame Relay PVC to IP interface Configuring the PVC encapsulation typeMode PVC Disabling a Frame Relay PVC Enabling a Frame Relay PVCCRC Displaying serial port informationDlci Displaying Frame Relay informationIntegrated service access Port Configure the serial interface settingsCheck that the Frame Relay settings are correct Configure the introduced PVCsT1/E1 port configuration Enable/Disable T1/E1 port T1/E1 port configuration task listConfiguring T1/E1 line-code Mode port e1t1 slot portConfiguring T1/E1 port-type Configuring T1/E1 clock-modeName prt-e1t1 slot/port# framing Configuring T1/E1 framingConfiguring T1/E1 line-build-out T1 only Configuring T1/E1 used-connector E1 onlyDefault short-haul Configuring T1/E1 application modeConfiguring T1/E1 LOS threshold Configuring T1/E1 encapsulationConfiguring Channel-Group Encapsulation Be used Mode port e1t1 slot portConfiguring Channel-Group Timeslots Mode channel-group group-nameDefault no encapsulation Configuring Hdlc CRC-TypeConfiguring Hdlc Encapsulation T1/E1 Configuration ExamplesExample 1 Frame Relay without a channel-group Example 4 PPP with a channel-group Example 2 Framerelay with a channel-groupExample 3 PPP without a channel-group VPN configuration Encryption AuthenticationCreating an IPsec transformation profile VPN configuration task listTransport and tunnel modes Creating an IPsec policy profile Procedure To create an IPsec policy profileNodecfg#profile ipsec-policy-man Creating/modifying an outgoing ACL profile for IPsec Displaying IPsec configuration information Configuration of an IP interface and the IP router for IPsecExample IPsec Debug Output Example Display IPsec transformation profilesExample Display IPsec policy profiles Debugging IPsecIPsec tunnel, DES encryption Sample configurationsOnSite configuration Cisco router configuration Cisco router configuration VPN configuration Access control list configuration Why you should configure access lists About access control listsWhat access lists do Features of access control lists When to configure access listsMapping out the goals of the access control list Access control list configuration task listNodepf-acl name#permit ip src src-wildcard any Src-wildcard Where the syntax isAny host src dest dest-wildcard any host dest Nodepf-acl name#permit icmp src src-wildcard anyType type type type code code cos group Nodepf-acl name#deny icmp src src-wildcardMsg name Where the syntax is as followingNodepf-acl name#deny tcp udp sctp src src Nodepf-acl name#permit tcp udp sctp src src-wildCard any host src eq port gt port lt port range Port lt port range from to cos group cos-rtp groupGroup-data Where the syntax is Debugging an access control list profile Unbind an access control list profile from an interfaceDisplaying an access control list profile Control list profile shall be debugged Denying a specific subnet ExamplesLink scheduler configuration Configuring access control lists Applying scheduling at the bottleneck Configuring quality of service QoSUsing traffic classes Priority Weighted fair queuing WFQIntroduction to Scheduling Hierarchy ShapingBurst tolerant shaping or wfq Some explanations Setting the modem rateQuick references Command cross reference Link scheduler configuration task listPacket classification Defining the access control list profileScenario with Web server regarded as a single source host Creating an access control listNodepf-acl name#permit ip any any Creating a service policy profileNodecfg#profile acl name Nodepf-acl name#permit ip host ip-address any traffic-classStructure of a Service-Policy Profile Specifying the handling of traffic-classes Defining fair queuing weightDefining the maximum queue length Specifying the type-of-service TOS fieldDefining the bit-rate Defining absolute priorityNodesrc name#set ip precedence value Specifying differentiated services codepoint Dscp markingSpecifying the precedence field Nodesrc name#set ip tos valueNodesrc name#set layer2 cos value Specifying layer 2 markingNodesrc name#set ip dscp value Nodesrc name#random-detect burst-tolerance Defining random early detectionDiscarding Excess Load Policy name in out Devoting the service policy profile to an interfaceNodeif-ip if-name#use profile service Displaying link scheduling profile information Enable statistics gatheringDisplaying link arbitration status Values defining detail of the queuing statistics LEDs status and monitoring Status LEDs Contacting Patton for assistance Patton Support Headquarters in the USA Warranty coverageContact information RMA numbers Out-of-warranty serviceReturns for credit Return for credit policyAppendix a Compliance information CE Declaration of Conformity SafetyCompliance Radio and TV Interference FCC PartIndustry Canada Notice Model 2803 only Authorized European RepresentativeFCC Part 68 Acta Statement Model 2803 only Appendix B Specifications PPP support Ethernet interfacesSync serial interface T1/E1 interface Model 2803 onlyOperating environment IP servicesDimensions ManagementInternal AC version Power supplyInternal power supply 100-240 VAC, 50/60 Hz, 200 mA Appendix C Cabling Serial console Connecting a serial terminalEthernet cross-over Ethernet 10Base-T and 100Base-TEthernet straight-through Appendix D Port pin-outs EIA-561 RJ-45 8-pin port RS-232 Console Port Console port, RJ-45, EIA-561 RS-232Serial port Ethernet 10Base-T and 100Base-T portSync serial port Ethernet ports are auto-detect MDI-X21 Female DB-15 connector Appendix E OnSite 2800 Series factory configuration OnSite 2800 Series factory configuration Appendix F Installation checklist Installation checklist
Related manuals
Manual 8 pages 44.23 Kb