Configuring Windows | Actiontec electronic V.90 ISA guide

Configuring Windows 95

Step 1 Upon start-up, Windows 95 detects the modem and displays the New Hard- ware Found dialog box. Select “Driver from disk provided by hardware manufacturer” then Click OK.

Step 2 Insert the diskette containing the modem’s Windows 95 .INF files and click

OK

Step 3 If Windows asks for an installation disk, click OK and type A: in the dialog box that appears and click OK again.

Step 4 After the installer has copied the .INF files to the hard disk, a New Hard- ware Found dialog box should appear prompting for the “Wave Device for Voice Modem”. Click OK. (See “Do This First” for information on UNIMODEM.INF if this screen does not appear).

9

Image 9

Actiontec electronic V.90 ISA user manual Configuring Windows

Contents

ISA Plug n Play Voice/Fax Modem Table of Contents Contacting Actiontec Customer Support Introduction Before You Begin For Windows 95/98 Installation For Windows NT 4.0 Installation Hardware Installation Installing The Modem Installing The Modem Connecting Devices Connecting Devices to the Modem Configuring Windows Page Finish Configuring Windows 95 OSR2Page Page Configuring Windows Page Page Page Page Configuring Windows NT Page Page Page Page Fax TIA/EIA-578 for Class 1 Fax Voice Installing Communications SoftwareInit String AT&F&C1&D2W2 Windows 95/98 Troubleshooting More Info Panel No Dialtone Error Common Problems Communications Software Does Not Work COM Ports and Interrupts Appendix a Non Plug-N-Play Installations Jumper Settings Jumpers Set To Plug-N-Play default setting Installing In DOS and Windows Hardware and Driver InstallationRemove Page Repeat Last Command Appendix B AT Command SetAnswer Command ATXn Carrier Control Result Codes Last number dialed DnDial Echo Command Online Data Character Echo CommandHook Control Monitor Speaker Volume This command sets speaker volume to low, medium, or highRequest ID Information Modulation Handshake This command turns the speaker on or off Return On-line to Data Mode Select Pulse DialingResult Code Control Result Code Option DCE Response Format Dial Tone Detect Extended Result Codes Busy Tone Detect Long space disconnect is always disabledLong Space Disconnect Recall Stored Profile Auto Retrain This modem always auto retrainsData Carrier Detect DCD Control DTR Control Load Factory Settings Local Flow Control Selection Auxiliary Relay option Asynchronous Communications Mode This Command is effective only for use in JapanPulse Dial Make-to-Break Ratio Selection Data Set Ready DSR Option This command selects DSR action Below is an example of a possible output This command is used to display the active profiles SSE Zn=x \An\Bn Modem Port Flow Control Adjust Bits/s Rate Control \Kn \Nn Error Control Mode Selection = 0, 1, 2, 3, 4, 5 \Tn Inactivity Timer \Vn Protocol Result Code\Xn XON/XOFF Pass Through Enable/Disable Data Compression Data Calling ToneView Numbers in Blacklist Self-Test Commands AT Commands for Testing and DebuggingWrite to/Read from DSP Register Line-to-Line Loopback ATI11 Type Registers Reference Range 0−255 Default UnitsASCII Range 0−255 Default UnitsringsRange −127, Ascii decimal Default Carriage return Units Range −127, Ascii decimal Default Line feed Units Range Default Unitsseconds Range −32 Default Backspace UnitsConnection Completion Time-Out Comma Dial Modifier Time S11 Dtmf Dialing Speed S10S12 Escape Guard Time S14 General Bit Mapped Options Status S24 Timer to Control Sleep Mode S21S22 S30 Inactivity Timer S28 Modulation Enable/DisableS32 S33 S38 56K Dial Line Rate default S37 Dial Line Rate defaultS36 Connection S42 Auto Rate default 1, range S43 Auto Mode default 1, rangeS48 Lapm Error Control and Feature Negotiation default S90 S89 Timer to Control Sleep ModeS91 S92 No Carrier S109K56flex and V.90 Selection default Result Code Declaration of Conformity Appendix B Communications Regulations Canadian Department of Communications Cdoc