DCE Response Format | Actiontec electronic V.90 ISA instruction

T	Select Tone Dialing

This command instructs the modem to send DTMF tones while dialing. Dialed digits are tone dialed until a P command or dial modifier is received. This is the default setting.

Vn	DCE Response Format

This command controls whether result codes (including call progress and negotia- tion progress messages) are displayed as words or their numeric equivalents.

	Command			Effect

	V0			Not supported. Results are always text.

	V1			Displays result codes as text (default).

Result Codes:

	OK	n = 0, 1

	ERROR	Otherwise

Wn			Result Code Option

	Command			Effect

	W0			CONNECT result code reports DTE speed. Disable
	W0			protocol result codes.
				protocol result codes.

	W1			CONNECT result code reports DTE speed. Enable
	W1			protocol result codes.
				protocol result codes.

	W2			CONNECT result code reports DCE speed. Enable
	W2			protocol result codes (default).
				protocol result codes (default).

Result Codes:

	OK	n = 0, 1, 2

	ERROR	Otherwise

41

Image 41

Actiontec electronic V.90 ISA user manual DCE Response Format, Result Code Option

Contents

ISA Plug n Play Voice/Fax Modem Table of Contents Contacting Actiontec Customer Support Introduction Before You Begin For Windows 95/98 Installation For Windows NT 4.0 Installation Hardware Installation Installing The Modem Installing The Modem Connecting Devices Connecting Devices to the Modem Configuring Windows Page Finish Configuring Windows 95 OSR2Page Page Configuring Windows Page Page Page Page Configuring Windows NT Page Page Page Page Fax TIA/EIA-578 for Class 1 Fax Voice Installing Communications SoftwareInit String AT&F&C1&D2W2 Windows 95/98 Troubleshooting More Info Panel No Dialtone Error Common Problems Communications Software Does Not Work COM Ports and Interrupts Appendix a Non Plug-N-Play Installations Jumper Settings Jumpers Set To Plug-N-Play default setting Remove Installing In DOS and WindowsHardware and Driver Installation Page Repeat Last Command Appendix B AT Command SetAnswer Command ATXn Carrier Control Result Codes Last number dialed DnDial Hook Control Echo CommandOnline Data Character Echo Command Request ID Information Monitor Speaker VolumeThis command sets speaker volume to low, medium, or high Modulation Handshake This command turns the speaker on or off Result Code Control Return On-line to Data ModeSelect Pulse Dialing Result Code Option DCE Response Format Dial Tone Detect Extended Result Codes Busy Tone Detect Long space disconnect is always disabledLong Space Disconnect Recall Stored Profile Data Carrier Detect DCD Control Auto RetrainThis modem always auto retrains DTR Control Load Factory Settings Local Flow Control Selection Auxiliary Relay option Pulse Dial Make-to-Break Ratio Selection Asynchronous Communications ModeThis Command is effective only for use in Japan Data Set Ready DSR Option This command selects DSR action Below is an example of a possible output This command is used to display the active profiles SSE \Bn Zn=x\An Modem Port Flow Control Adjust Bits/s Rate Control \Kn \Nn Error Control Mode Selection = 0, 1, 2, 3, 4, 5 \Xn XON/XOFF Pass Through \Tn Inactivity Timer\Vn Protocol Result Code View Numbers in Blacklist Enable/Disable Data CompressionData Calling Tone Self-Test Commands AT Commands for Testing and DebuggingWrite to/Read from DSP Register Line-to-Line Loopback ATI11 Type Registers Reference Range 0−255 Default UnitsASCII Range 0−255 Default UnitsringsRange −127, Ascii decimal Default Carriage return Units Range −127, Ascii decimal Default Line feed Units Range Default Unitsseconds Range −32 Default Backspace UnitsConnection Completion Time-Out Comma Dial Modifier Time S11 Dtmf Dialing Speed S10S12 Escape Guard Time S14 General Bit Mapped Options Status S22 S24 Timer to Control Sleep ModeS21 S30 Inactivity Timer S28 Modulation Enable/DisableS32 S33 S38 56K Dial Line Rate default S37 Dial Line Rate defaultS36 Connection S48 Lapm Error Control and Feature Negotiation default S42 Auto Rate default 1, rangeS43 Auto Mode default 1, range S90 S89 Timer to Control Sleep ModeS91 S92 No Carrier S109K56flex and V.90 Selection default Result Code Declaration of Conformity Appendix B Communications Regulations Canadian Department of Communications Cdoc