Modem Port Flow Control | Actiontec electronic V.90 ISA specification

\G		Modem Port Flow Control

	Command		Effect

	\G0		Returns an “OK” for compatibility (default).

	\G1		NOT SUPPORTED responds ERROR.

Result Codes:

	OK	n = 0

	ERROR	Otherwise

\J		Adjust Bits/s Rate Control

When this feature is enabled, the modem emulates the behavior of modems that force the DTE interface to the line speed.

Command	Effect

\J0	Turn off feature (default).

\J1	Turn on feature.

Result Codes:

OK

n = 0, 1

ERROR Otherwise

52

Image 52

Actiontec electronic V.90 ISA user manual Modem Port Flow Control, Adjust Bits/s Rate Control

Contents

ISA Plug n Play Voice/Fax Modem Table of Contents Introduction Contacting Actiontec Customer Support For Windows 95/98 Installation Before You Begin For Windows NT 4.0 Installation Installing The Modem Hardware Installation Installing The Modem Connecting Devices to the Modem Connecting Devices Configuring Windows Page Configuring Windows 95 OSR2 FinishPage Page Configuring Windows Page Page Page Page Configuring Windows NT Page Page Page Page Installing Communications Software Fax TIA/EIA-578 for Class 1 Fax VoiceInit String AT&F&C1&D2W2 Troubleshooting Windows 95/98 More Info Panel Common Problems No Dialtone Error Communications Software Does Not Work Appendix a Non Plug-N-Play Installations COM Ports and Interrupts Jumper Settings Jumpers Set To Plug-N-Play default setting Hardware and Driver Installation Installing In DOS and WindowsRemove Page Appendix B AT Command Set Repeat Last CommandAnswer Command ATXn Result Codes Carrier Control DnDial Last number dialed Online Data Character Echo Command Echo CommandHook Control This command sets speaker volume to low, medium, or high Monitor Speaker VolumeRequest ID Information This command turns the speaker on or off Modulation Handshake Select Pulse Dialing Return On-line to Data ModeResult Code Control DCE Response Format Result Code Option Extended Result Codes Dial Tone Detect Long space disconnect is always disabled Busy Tone DetectLong Space Disconnect Recall Stored Profile This modem always auto retrains Auto RetrainData Carrier Detect DCD Control Load Factory Settings DTR Control Auxiliary Relay option Local Flow Control Selection This Command is effective only for use in Japan Asynchronous Communications ModePulse Dial Make-to-Break Ratio Selection This command selects DSR action Data Set Ready DSR Option This command is used to display the active profiles Below is an example of a possible output SSE \An Zn=x\Bn Adjust Bits/s Rate Control Modem Port Flow Control \Kn \Nn Error Control Mode Selection = 0, 1, 2, 3, 4, 5 \Vn Protocol Result Code \Tn Inactivity Timer\Xn XON/XOFF Pass Through Data Calling Tone Enable/Disable Data CompressionView Numbers in Blacklist AT Commands for Testing and Debugging Self-Test CommandsWrite to/Read from DSP Register Line-to-Line Loopback ATI11 Registers Reference Type Range 0−255 Default Unitsrings Range 0−255 Default UnitsASCIIRange −127, Ascii decimal Default Carriage return Units Range −127, Ascii decimal Default Line feed Units Range −32 Default Backspace Units Range Default UnitssecondsConnection Completion Time-Out Comma Dial Modifier Time S10 S11 Dtmf Dialing SpeedS12 Escape Guard Time S14 General Bit Mapped Options Status S21 S24 Timer to Control Sleep ModeS22 S28 Modulation Enable/Disable S30 Inactivity TimerS32 S33 S37 Dial Line Rate default S38 56K Dial Line Rate defaultS36 Connection S43 Auto Mode default 1, range S42 Auto Rate default 1, rangeS48 Lapm Error Control and Feature Negotiation default S89 Timer to Control Sleep Mode S90S91 S92 S109K56flex and V.90 Selection default No Carrier Result Code Appendix B Communications Regulations Declaration of Conformity Canadian Department of Communications Cdoc