= 0, 1, 2, 3, 4, 5 | Actiontec electronic V.90 ISA manual

Result Codes:

	OK	n = 0, 1, 2, 3, 4, 5, 7

	ERROR	Otherwise

\Q		Local Flow Control Selection

	Command		Effect

	\Q0		Disable flow control. Same as &K0.

	\Q1		XON/XOFF software flow control. Same as &K4.

	\Q2		CTS-only flow control. This is not supported, and the
	\Q2		response is ERROR.
			response is ERROR.

	\Q3		RTS/CTS to DTE (default). Same as &K3.

Result Codes:

	OK	n = 0, 1, 3

	ERROR	Otherwise

\Rn		Ring indicator signal off after the telephone call is answered
		(Compatibility command)

	Command		Effect

	\R0		Ring indicator signal is off after the telephone call is
	\R0		answered
			answered

Result Codes:

	OK	n = 0

	ERROR	Otherwise

55

Image 55

Actiontec electronic V.90 ISA user manual = 0, 1, 2, 3, 4, 5

Contents

ISA Plug n Play Voice/Fax Modem Table of Contents Contacting Actiontec Customer Support Introduction Before You Begin For Windows 95/98 Installation For Windows NT 4.0 Installation Hardware Installation Installing The Modem Installing The Modem Connecting Devices Connecting Devices to the Modem Configuring Windows Page Finish Configuring Windows 95 OSR2Page Page Configuring Windows Page Page Page Page Configuring Windows NT Page Page Page Page AT&F&C1&D2W2 Installing Communications SoftwareFax TIA/EIA-578 for Class 1 Fax Voice Init String Windows 95/98 Troubleshooting More Info Panel No Dialtone Error Common Problems Communications Software Does Not Work COM Ports and Interrupts Appendix a Non Plug-N-Play Installations Jumper Settings Jumpers Set To Plug-N-Play default setting Hardware and Driver Installation Installing In DOS and WindowsRemove Page ATXn Appendix B AT Command SetRepeat Last Command Answer Command Carrier Control Result Codes Last number dialed DnDial Online Data Character Echo Command Echo CommandHook Control This command sets speaker volume to low, medium, or high Monitor Speaker VolumeRequest ID Information Modulation Handshake This command turns the speaker on or off Select Pulse Dialing Return On-line to Data ModeResult Code Control Result Code Option DCE Response Format Dial Tone Detect Extended Result Codes Recall Stored Profile Long space disconnect is always disabledBusy Tone Detect Long Space Disconnect This modem always auto retrains Auto RetrainData Carrier Detect DCD Control DTR Control Load Factory Settings Local Flow Control Selection Auxiliary Relay option This Command is effective only for use in Japan Asynchronous Communications ModePulse Dial Make-to-Break Ratio Selection Data Set Ready DSR Option This command selects DSR action Below is an example of a possible output This command is used to display the active profiles SSE \An Zn=x\Bn Modem Port Flow Control Adjust Bits/s Rate Control \Kn \Nn Error Control Mode Selection = 0, 1, 2, 3, 4, 5 \Vn Protocol Result Code \Tn Inactivity Timer\Xn XON/XOFF Pass Through Data Calling Tone Enable/Disable Data CompressionView Numbers in Blacklist Line-to-Line Loopback AT Commands for Testing and DebuggingSelf-Test Commands Write to/Read from DSP Register ATI11 Type Registers Reference Range −127, Ascii decimal Default Line feed Units Range 0−255 Default UnitsringsRange 0−255 Default UnitsASCII Range −127, Ascii decimal Default Carriage return Units Comma Dial Modifier Time Range −32 Default Backspace UnitsRange Default Unitsseconds Connection Completion Time-Out S14 General Bit Mapped Options Status S10S11 Dtmf Dialing Speed S12 Escape Guard Time S21 S24 Timer to Control Sleep ModeS22 S33 S28 Modulation Enable/DisableS30 Inactivity Timer S32 Connection S37 Dial Line Rate defaultS38 56K Dial Line Rate default S36 S43 Auto Mode default 1, range S42 Auto Rate default 1, rangeS48 Lapm Error Control and Feature Negotiation default S92 S89 Timer to Control Sleep ModeS90 S91 No Carrier S109K56flex and V.90 Selection default Result Code Declaration of Conformity Appendix B Communications Regulations Canadian Department of Communications Cdoc