Configuring Windows 95 OSR2, Finish | Actiontec electronic V.90 ISA

Configuring Windows 95 OSR2

Step 1 On start-up Windows 95 will detect the modem and launch the Update Device Driver Wizard dialog box. Insert the modem’s Installation CD-ROM, wait about 10 seconds so that the CD-ROM can be read by the drive, and click Next.

Step 2 After Windows 95 has found the updated drivers for your modem, click

Finish.

11

Image 11

Actiontec electronic V.90 ISA user manual Configuring Windows 95 OSR2, Finish

Contents

ISA Plug n Play Voice/Fax Modem Table of Contents Contacting Actiontec Customer Support Introduction Before You Begin For Windows 95/98 Installation For Windows NT 4.0 Installation Hardware Installation Installing The Modem Installing The Modem Connecting Devices Connecting Devices to the Modem Configuring Windows Page Finish Configuring Windows 95 OSR2Page Page Configuring Windows Page Page Page Page Configuring Windows NT Page Page Page Page AT&F&C1&D2W2 Installing Communications SoftwareFax TIA/EIA-578 for Class 1 Fax Voice Init String Windows 95/98 Troubleshooting More Info Panel No Dialtone Error Common Problems Communications Software Does Not Work COM Ports and Interrupts Appendix a Non Plug-N-Play Installations Jumper Settings Jumpers Set To Plug-N-Play default setting Remove Installing In DOS and WindowsHardware and Driver Installation Page ATXn Appendix B AT Command SetRepeat Last Command Answer Command Carrier Control Result Codes Last number dialed DnDial Hook Control Echo CommandOnline Data Character Echo Command Request ID Information Monitor Speaker VolumeThis command sets speaker volume to low, medium, or high Modulation Handshake This command turns the speaker on or off Result Code Control Return On-line to Data ModeSelect Pulse Dialing Result Code Option DCE Response Format Dial Tone Detect Extended Result Codes Recall Stored Profile Long space disconnect is always disabledBusy Tone Detect Long Space Disconnect Data Carrier Detect DCD Control Auto RetrainThis modem always auto retrains DTR Control Load Factory Settings Local Flow Control Selection Auxiliary Relay option Pulse Dial Make-to-Break Ratio Selection Asynchronous Communications ModeThis Command is effective only for use in Japan Data Set Ready DSR Option This command selects DSR action Below is an example of a possible output This command is used to display the active profiles SSE \Bn Zn=x\An Modem Port Flow Control Adjust Bits/s Rate Control \Kn \Nn Error Control Mode Selection = 0, 1, 2, 3, 4, 5 \Xn XON/XOFF Pass Through \Tn Inactivity Timer\Vn Protocol Result Code View Numbers in Blacklist Enable/Disable Data CompressionData Calling Tone Line-to-Line Loopback AT Commands for Testing and DebuggingSelf-Test Commands Write to/Read from DSP Register ATI11 Type Registers Reference Range −127, Ascii decimal Default Line feed Units Range 0−255 Default UnitsringsRange 0−255 Default UnitsASCII Range −127, Ascii decimal Default Carriage return Units Comma Dial Modifier Time Range −32 Default Backspace UnitsRange Default Unitsseconds Connection Completion Time-Out S14 General Bit Mapped Options Status S10S11 Dtmf Dialing Speed S12 Escape Guard Time S22 S24 Timer to Control Sleep ModeS21 S33 S28 Modulation Enable/DisableS30 Inactivity Timer S32 Connection S37 Dial Line Rate defaultS38 56K Dial Line Rate default S36 S48 Lapm Error Control and Feature Negotiation default S42 Auto Rate default 1, rangeS43 Auto Mode default 1, range S92 S89 Timer to Control Sleep ModeS90 S91 No Carrier S109K56flex and V.90 Selection default Result Code Declaration of Conformity Appendix B Communications Regulations Canadian Department of Communications Cdoc