No Carrier | Actiontec electronic V.90 ISA guide

S109K56flex and V.90 Selection (default 1)

Use this register to disable 56K connections or to choose between K56flex and V.90 protocols. The default setting (S109=1) will attempt K56flex first, then V.90, and then V.34 depending upon the central site modem being called and your phone line conditions. (see the next page for listing.)

S109 = 0	Disable all 56K connections
S109 = 1	K56flex first, then V.90 (default)
S109 = 2	V.90 only. K56flex disabled
Table 2. The Result Code Summary
Result Code		Description
OK		Command executed
CONNECT		Modem connected to line
RING		A ring signal has been detected
NO CARRIER		Modem lost carrier signal, or does not detect carrier signal, or
		does not detect answer tone
ERROR		Iinvalid command
CONNECT 1200 EC*		Connection at 1200 bits/s
NO DIALTONE		No dial tone detected
BUSY		Busy signal detected
NO ANSWER8		No quiet answer
CONNECT 2400 EC*		Connection at 2400 bits/s
CONNECT 4800 EC*		Connection at 4800 bits/s
CONNECT 9600 EC*		Connection at 9600 bits/s
CONNECT 14400 EC*		Connection at 14400 bits/s
CONNECT 19200 EC*		Connection at 19200 bits/s
CONNECT 7200 EC*		Connection at 7200 bits/s
CONNECT 12000 EC*		Connection at 12000 bits/s
CONNECT 16800 EC*		Connection at 16800 bits/s
CONNECT 300 EC*		Connection at 300 bits/s
CONNECT 21600 EC*		Connection at 21600 bits/s
CONNECT 24000 EC*		Connection at 24000 bits/s
CONNECT 26400 EC*		Connection at 26400 bits/s
CONNECT 28800 EC*		Connection at 28800 bits/s
CONNECT 31200 EC*		Connection at 31200 bits/s
CONNECT 33600 EC*		Connection at 33600 bits/s
CONNECT 38400 EC*		Connection at 38400 bits/s
CONNECT 57600 EC*		Connection at 57600 bits/s
CONNECT 115200 EC		Connection at 115200 bits/s
DELAYED		Delay is in effect for the dialed number
BLACKLISTED		Dialed number is blacklisted
BLACKLIST FULL		Blacklist is full
CONNECT 32000 EC*		Connection at 32000 bits/s, 56K rate
CONNECT 34000 EC*		Connection at 34000 bits/s, 56K rate
CONNECT 36000 EC*		Connection at 36000 bits/s, 56K rate
CONNECT 38000 EC*		Connection at 38000 bits/s, 56K rate
CONNECT 40000 EC*		Connection at 40000 bits/s, 56K rate

69

Image 69

Actiontec electronic V.90 ISA user manual S109K56flex and V.90 Selection default, No Carrier

Contents

ISA Plug n Play Voice/Fax Modem Table of Contents Contacting Actiontec Customer Support Introduction Before You Begin For Windows 95/98 Installation For Windows NT 4.0 Installation Hardware Installation Installing The Modem Installing The Modem Connecting Devices Connecting Devices to the Modem Configuring Windows Page Finish Configuring Windows 95 OSR2Page Page Configuring Windows Page Page Page Page Configuring Windows NT Page Page Page Page Fax TIA/EIA-578 for Class 1 Fax Voice Installing Communications SoftwareInit String AT&F&C1&D2W2 Windows 95/98 Troubleshooting More Info Panel No Dialtone Error Common Problems Communications Software Does Not Work COM Ports and Interrupts Appendix a Non Plug-N-Play Installations Jumper Settings Jumpers Set To Plug-N-Play default setting Installing In DOS and Windows Hardware and Driver InstallationRemove Page Repeat Last Command Appendix B AT Command SetAnswer Command ATXn Carrier Control Result Codes Last number dialed DnDial Echo Command Online Data Character Echo CommandHook Control Monitor Speaker Volume This command sets speaker volume to low, medium, or highRequest ID Information Modulation Handshake This command turns the speaker on or off Return On-line to Data Mode Select Pulse DialingResult Code Control Result Code Option DCE Response Format Dial Tone Detect Extended Result Codes Busy Tone Detect Long space disconnect is always disabledLong Space Disconnect Recall Stored Profile Auto Retrain This modem always auto retrainsData Carrier Detect DCD Control DTR Control Load Factory Settings Local Flow Control Selection Auxiliary Relay option Asynchronous Communications Mode This Command is effective only for use in JapanPulse Dial Make-to-Break Ratio Selection Data Set Ready DSR Option This command selects DSR action Below is an example of a possible output This command is used to display the active profiles SSE Zn=x \An\Bn Modem Port Flow Control Adjust Bits/s Rate Control \Kn \Nn Error Control Mode Selection = 0, 1, 2, 3, 4, 5 \Tn Inactivity Timer \Vn Protocol Result Code\Xn XON/XOFF Pass Through Enable/Disable Data Compression Data Calling ToneView Numbers in Blacklist Self-Test Commands AT Commands for Testing and DebuggingWrite to/Read from DSP Register Line-to-Line Loopback ATI11 Type Registers Reference Range 0−255 Default UnitsASCII Range 0−255 Default UnitsringsRange −127, Ascii decimal Default Carriage return Units Range −127, Ascii decimal Default Line feed Units Range Default Unitsseconds Range −32 Default Backspace UnitsConnection Completion Time-Out Comma Dial Modifier Time S11 Dtmf Dialing Speed S10S12 Escape Guard Time S14 General Bit Mapped Options Status S24 Timer to Control Sleep Mode S21S22 S30 Inactivity Timer S28 Modulation Enable/DisableS32 S33 S38 56K Dial Line Rate default S37 Dial Line Rate defaultS36 Connection S42 Auto Rate default 1, range S43 Auto Mode default 1, rangeS48 Lapm Error Control and Feature Negotiation default S90 S89 Timer to Control Sleep ModeS91 S92 No Carrier S109K56flex and V.90 Selection default Result Code Declaration of Conformity Appendix B Communications Regulations Canadian Department of Communications Cdoc