Auxiliary Relay option | Actiontec electronic V.90 ISA instruction

&Gn	V.22bis Guard Tone Control

This command determines which guard tone, if any, to transmit while transmitting in the high band (answer mode). This command is only used in V.22 and V.22bis mode. This option is not used in North America and is for international use only.

	Command		Effect

	&G0		Guard tone disabled (default).

	&G1		Sets guard tone to 550 Hz.

	&G2		Sets guard tone to 1800 Hz.

Result Codes:

	OK	n = 0, 1, 2

	ERROR	Otherwise

&Jn		Auxiliary Relay option

	Command		Effect

	&J0		The auxiliary relay is never closed.

	&J1		NOT SUPPORTED, responds ERROR.

Result Codes:

	OK	n = 0

	ERROR	Otherwise

&Kn		Local Flow Control Selection

	Command		Effect

	&K0		Disable flow control.

	&K1		Reserved.

	&K2		Reserved.

	&K3		Enable RTS/CTS flow control (default).

	&K4		Enable XON/XOFF flow control.

46

Image 46

Actiontec electronic V.90 ISA user manual Auxiliary Relay option, Local Flow Control Selection

Contents

ISA Plug n Play Voice/Fax Modem Table of Contents Introduction Contacting Actiontec Customer Support For Windows 95/98 Installation Before You Begin For Windows NT 4.0 Installation Installing The Modem Hardware Installation Installing The Modem Connecting Devices to the Modem Connecting Devices Configuring Windows Page Configuring Windows 95 OSR2 FinishPage Page Configuring Windows Page Page Page Page Configuring Windows NT Page Page Page Page Init String Installing Communications SoftwareFax TIA/EIA-578 for Class 1 Fax Voice AT&F&C1&D2W2 Troubleshooting Windows 95/98 More Info Panel Common Problems No Dialtone Error Communications Software Does Not Work Appendix a Non Plug-N-Play Installations COM Ports and Interrupts Jumper Settings Jumpers Set To Plug-N-Play default setting Hardware and Driver Installation Installing In DOS and WindowsRemove Page Answer Command Appendix B AT Command SetRepeat Last Command ATXn Result Codes Carrier Control DnDial Last number dialed Online Data Character Echo Command Echo CommandHook Control This command sets speaker volume to low, medium, or high Monitor Speaker VolumeRequest ID Information This command turns the speaker on or off Modulation Handshake Select Pulse Dialing Return On-line to Data ModeResult Code Control DCE Response Format Result Code Option Extended Result Codes Dial Tone Detect Long Space Disconnect Long space disconnect is always disabledBusy Tone Detect Recall Stored Profile This modem always auto retrains Auto RetrainData Carrier Detect DCD Control Load Factory Settings DTR Control Auxiliary Relay option Local Flow Control Selection This Command is effective only for use in Japan Asynchronous Communications ModePulse Dial Make-to-Break Ratio Selection This command selects DSR action Data Set Ready DSR Option This command is used to display the active profiles Below is an example of a possible output SSE \An Zn=x\Bn Adjust Bits/s Rate Control Modem Port Flow Control \Kn \Nn Error Control Mode Selection = 0, 1, 2, 3, 4, 5 \Vn Protocol Result Code \Tn Inactivity Timer\Xn XON/XOFF Pass Through Data Calling Tone Enable/Disable Data CompressionView Numbers in Blacklist Write to/Read from DSP Register AT Commands for Testing and DebuggingSelf-Test Commands Line-to-Line Loopback ATI11 Registers Reference Type Range −127, Ascii decimal Default Carriage return Units Range 0−255 Default UnitsringsRange 0−255 Default UnitsASCII Range −127, Ascii decimal Default Line feed Units Connection Completion Time-Out Range −32 Default Backspace UnitsRange Default Unitsseconds Comma Dial Modifier Time S12 Escape Guard Time S10S11 Dtmf Dialing Speed S14 General Bit Mapped Options Status S21 S24 Timer to Control Sleep ModeS22 S32 S28 Modulation Enable/DisableS30 Inactivity Timer S33 S36 S37 Dial Line Rate defaultS38 56K Dial Line Rate default Connection S43 Auto Mode default 1, range S42 Auto Rate default 1, rangeS48 Lapm Error Control and Feature Negotiation default S91 S89 Timer to Control Sleep ModeS90 S92 S109K56flex and V.90 Selection default No Carrier Result Code Appendix B Communications Regulations Declaration of Conformity Canadian Department of Communications Cdoc