Sse | Actiontec electronic V.90 ISA manual

Option	Selection	AT Cmd
No Carrier Disc	2000 msec	S10
DTMF Dial Speed	95 msec	S11
Escape Guard Time	1000 msec	S12
Data Calling Tone	Disabled	S35
Line Rate	33600	S37
DSVD mode	Disabled	-SSE

Stored Phone Numbers

&Z0=

&Z1=

&Z2=

&Z3=

OK

&Wn	Store Current Configuration

This command stores certain command options and S-register values into the modem’s nonvolatile memory. The ATZ command or a powerup reset of the modem restores this profile.

Result Codes:

OK	n = 0

ERROR	Otherwise

&Yn	Select Stored Profile for Hard Reset

This command does not change the behavior of the modem but is included for com- patibility with applications that issue the &Y0 command:

Command	Effect

&Y0	Select stored profile 0 on powerup

&Y1	ERROR

Result Codes:

OK

n = 0

ERROR Otherwise

50

Image 50

Actiontec electronic V.90 ISA user manual Sse

Contents

ISA Plug n Play Voice/Fax Modem Table of Contents Introduction Contacting Actiontec Customer Support For Windows 95/98 Installation Before You Begin For Windows NT 4.0 Installation Installing The Modem Hardware Installation Installing The Modem Connecting Devices to the Modem Connecting Devices Configuring Windows Page Configuring Windows 95 OSR2 FinishPage Page Configuring Windows Page Page Page Page Configuring Windows NT Page Page Page Page Init String Installing Communications SoftwareFax TIA/EIA-578 for Class 1 Fax Voice AT&F&C1&D2W2 Troubleshooting Windows 95/98 More Info Panel Common Problems No Dialtone Error Communications Software Does Not Work Appendix a Non Plug-N-Play Installations COM Ports and Interrupts Jumper Settings Jumpers Set To Plug-N-Play default setting Remove Installing In DOS and WindowsHardware and Driver Installation Page Answer Command Appendix B AT Command SetRepeat Last Command ATXn Result Codes Carrier Control DnDial Last number dialed Hook Control Echo CommandOnline Data Character Echo Command Request ID Information Monitor Speaker VolumeThis command sets speaker volume to low, medium, or high This command turns the speaker on or off Modulation Handshake Result Code Control Return On-line to Data ModeSelect Pulse Dialing DCE Response Format Result Code Option Extended Result Codes Dial Tone Detect Long Space Disconnect Long space disconnect is always disabledBusy Tone Detect Recall Stored Profile Data Carrier Detect DCD Control Auto RetrainThis modem always auto retrains Load Factory Settings DTR Control Auxiliary Relay option Local Flow Control Selection Pulse Dial Make-to-Break Ratio Selection Asynchronous Communications ModeThis Command is effective only for use in Japan This command selects DSR action Data Set Ready DSR Option This command is used to display the active profiles Below is an example of a possible output SSE \Bn Zn=x\An Adjust Bits/s Rate Control Modem Port Flow Control \Kn \Nn Error Control Mode Selection = 0, 1, 2, 3, 4, 5 \Xn XON/XOFF Pass Through \Tn Inactivity Timer\Vn Protocol Result Code View Numbers in Blacklist Enable/Disable Data CompressionData Calling Tone Write to/Read from DSP Register AT Commands for Testing and DebuggingSelf-Test Commands Line-to-Line Loopback ATI11 Registers Reference Type Range −127, Ascii decimal Default Carriage return Units Range 0−255 Default UnitsringsRange 0−255 Default UnitsASCII Range −127, Ascii decimal Default Line feed Units Connection Completion Time-Out Range −32 Default Backspace UnitsRange Default Unitsseconds Comma Dial Modifier Time S12 Escape Guard Time S10S11 Dtmf Dialing Speed S14 General Bit Mapped Options Status S22 S24 Timer to Control Sleep ModeS21 S32 S28 Modulation Enable/DisableS30 Inactivity Timer S33 S36 S37 Dial Line Rate defaultS38 56K Dial Line Rate default Connection S48 Lapm Error Control and Feature Negotiation default S42 Auto Rate default 1, rangeS43 Auto Mode default 1, range S91 S89 Timer to Control Sleep ModeS90 S92 S109K56flex and V.90 Selection default No Carrier Result Code Appendix B Communications Regulations Declaration of Conformity Canadian Department of Communications Cdoc