Result Code | Actiontec electronic V.90 ISA manual

Result Code

CONNECT 42000 EC* CONNECT 44000 EC* CONNECT 46000 EC* CONNECT 48000 EC* CONNECT 50000 EC* CONNECT 52000 EC* CONNECT 54000 EC* CONNECT 56000 EC* CONNECT 58000 EC* CONNECT 60000 EC* CONNECT 28000 EC* CONNECT 29333 EC* CONNECT 30666 EC* CONNECT 32000 EC* CONNECT 33333 EC* CONNECT 34666 EC* CONNECT 36000 EC* CONNECT 37333 EC* CONNECT 38666 EC* CONNECT 40000 EC* CONNECT 41333 EC* CONNECT 42666 EC* CONNECT 44000 EC* CONNECT 45333 EC* CONNECT 46666 EC* CONNECT 48000 EC* CONNECT 49333 EC* CONNECT 50666 EC* CONNECT 52000 EC* CONNECT 53333 EC*

Description

Connection at 42000 bits/s, 56K rate Connection at 44000 bits/s, 56K rate Connection at 46000 bits/s, 56K rate Connection at 48000 bits/s, 56K rate Connection at 50000 bits/s, 56K rate Connection at 52000 bits/s, 56K rate Connection at 54000 bits/s, 56K rate Connection at 56000 bits/s, 56K rate Connection at 58000 bits/s, 56K rate Connection at 60000 bits/s, 56K rate Connection at 28000 bits/s, V.90 rate Connection at 29333 bits/s, V.90 rate Connection at 30666 bits/s, V.90 rate Connection at 32000 bits/s, V.90 rate Connection at 33333 bits/s, V.90 rate Connection at 34666 bits/s, V.90 rate Connection at 36000 bits/s, V.90 rate Connection at 37333 bits/s, V.90 rate Connection at 38666 bits/s, V.90 rate Connection at 40000 bits/s, V.90 rate Connection at 41333 bits/s, V.90 rate Connection at 42666 bits/s, V.90 rate Connection at 44000 bits/s, V.90 rate Connection at 45333 bits/s, V.90 rate Connection at 46666 bits/s, V.90 rate Connection at 48000 bits/s, V.90 rate Connection at 49333 bits/s, V.90 rate Connection at 50666 bits/s, V.90 rate Connection at 52000 bits/s, V.90 rate Connection at 53333 bits/s, V.90 rate

*EC only appears when the Extended Result Codes configuration option is enabled. EC is replaced by one of the following symbols, depending upon the error control method used:

V42bis—V.42 error control and V.42bis data compression.

V42—V.42 error control only.

MNP 5— MNP class 4 error control and MNP class 5 data compression.

MNP 4— MNP class 4 error control only.

NoEC—No error control protocol.

70

Image 70

Actiontec electronic V.90 ISA user manual Result Code

Contents

ISA Plug n Play Voice/Fax Modem Table of Contents Introduction Contacting Actiontec Customer Support For Windows 95/98 Installation Before You Begin For Windows NT 4.0 Installation Installing The Modem Hardware Installation Installing The Modem Connecting Devices to the Modem Connecting Devices Configuring Windows Page Configuring Windows 95 OSR2 FinishPage Page Configuring Windows Page Page Page Page Configuring Windows NT Page Page Page Page Init String Installing Communications SoftwareFax TIA/EIA-578 for Class 1 Fax Voice AT&F&C1&D2W2 Troubleshooting Windows 95/98 More Info Panel Common Problems No Dialtone Error Communications Software Does Not Work Appendix a Non Plug-N-Play Installations COM Ports and Interrupts Jumper Settings Jumpers Set To Plug-N-Play default setting Hardware and Driver Installation Installing In DOS and WindowsRemove Page Answer Command Appendix B AT Command SetRepeat Last Command ATXn Result Codes Carrier Control DnDial Last number dialed Online Data Character Echo Command Echo CommandHook Control This command sets speaker volume to low, medium, or high Monitor Speaker VolumeRequest ID Information This command turns the speaker on or off Modulation Handshake Select Pulse Dialing Return On-line to Data ModeResult Code Control DCE Response Format Result Code Option Extended Result Codes Dial Tone Detect Long Space Disconnect Long space disconnect is always disabledBusy Tone Detect Recall Stored Profile This modem always auto retrains Auto RetrainData Carrier Detect DCD Control Load Factory Settings DTR Control Auxiliary Relay option Local Flow Control Selection This Command is effective only for use in Japan Asynchronous Communications ModePulse Dial Make-to-Break Ratio Selection This command selects DSR action Data Set Ready DSR Option This command is used to display the active profiles Below is an example of a possible output SSE \An Zn=x\Bn Adjust Bits/s Rate Control Modem Port Flow Control \Kn \Nn Error Control Mode Selection = 0, 1, 2, 3, 4, 5 \Vn Protocol Result Code \Tn Inactivity Timer\Xn XON/XOFF Pass Through Data Calling Tone Enable/Disable Data CompressionView Numbers in Blacklist Write to/Read from DSP Register AT Commands for Testing and DebuggingSelf-Test Commands Line-to-Line Loopback ATI11 Registers Reference Type Range −127, Ascii decimal Default Carriage return Units Range 0−255 Default UnitsringsRange 0−255 Default UnitsASCII Range −127, Ascii decimal Default Line feed Units Connection Completion Time-Out Range −32 Default Backspace UnitsRange Default Unitsseconds Comma Dial Modifier Time S12 Escape Guard Time S10S11 Dtmf Dialing Speed S14 General Bit Mapped Options Status S21 S24 Timer to Control Sleep ModeS22 S32 S28 Modulation Enable/DisableS30 Inactivity Timer S33 S36 S37 Dial Line Rate defaultS38 56K Dial Line Rate default Connection S43 Auto Mode default 1, range S42 Auto Rate default 1, rangeS48 Lapm Error Control and Feature Negotiation default S91 S89 Timer to Control Sleep ModeS90 S92 S109K56flex and V.90 Selection default No Carrier Result Code Appendix B Communications Regulations Declaration of Conformity Canadian Department of Communications Cdoc