TP-Link TL-WN727N manual In Windows Vista, 150Mbps Wireless N USB Adapter

Page 26

3.3.2 In Windows Vista

TL-WN727N

150Mbps Wireless N USB Adapter

Figure 3-21

3.3.2 In Windows Vista

Windows Vista users may use the built-in wireless utility. Follow the steps below.

1.Open the wireless utility by right-clicking on the wireless computer icon in your system tray as shown in the figure below. Select Connect to a network.

Figure 3-22

2.The utility will display any available wireless networks in your area. Highlight the wireless network you would like to connect and then click Connect.

19

Image 26

Contents TL-WN727N 150Mbps Wireless N USB Adapter Rev 3.2.0COPYRIGHT & TRADEMARKS FCC STATEMENT FCC RF Radiation Exposure StatementIndustry Canada Statement CE Mark WarningCanadian Compliance Statement Korea Warning StatementsSafety Information The product carries the CE Mark DECLARATION OF CONFORMITYProduct Description 150Mbps Wireless N USB Adapter Shennan Rd, Nanshan, Shenzhen, ChinaTo connect using Windows built-in wireless utility CONTENTSTo connect using WPS Hardware OverviewTL-WN727N Package Contents150Mbps Wireless N USB Adapter  Note1.1 Introduction 1.2 FeaturesChapter 1 Product Overview Working Status 1.3 Hardware OverviewStatus  Note2.2 Software Installation Chapter 2 Installation2.1 Hardware Installation 150Mbps Wireless N USB Adapter 5. Click Install to continue the setup 6. The utility and drivers will install. This may take 1~2 minutes 150Mbps Wireless N USB Adapter To connect using TWCU TP-LINK Wireless Configuration Utility Chapter 3 Connect to a Wireless Network3.1 To connect using TWCU To connect using WPS1 Wireless network of WPA/WPA2-Personal 2 Wireless network of WPA/WPA2-Enterprise 4. Please wait a few minutes for the connection process 3.2 To connect using WPS 3.2.1 PBC Push Button Configuration method150Mbps Wireless N USB Adapter 3.2.2 PIN method 3.2.2.1. Enter the PIN from your AP device2. The adapter will be connecting to the target network 3.2.2.2. Enter a PIN into your AP device3.3 To connect using Windows built-in wireless utility 3.3.1 In Windows3. You have now successfully connected to the network 3.3.2 In Windows Vista 4. You have now successfully connected to the network 3.3.3 In Windows XP 2. Right-click on the wireless computer icon in your system tray lower-right corner. Select View Available Wireless Networks 3.3.4 In Windows 2. If the network is unencrypted, you will directly connect to it  Note Chapter 4 Management 4.1 ProfileThe following items can be found on the screen 4.1.2 Modify a profile 4.2 Advanced 4.1.3 Delete a profile4.3 About Chapter 5 AP Mode  SoftAP mode Select to enable or disable the function Chapter 6 Uninstall Software 6.1 In Windows XP/Vista/76.1.2 Uninstall the driver software from your PC 6.2 In Windows 6.2.1 Uninstall the utility software from your PC6.2.2 Uninstall the driver software from your PC 4. Click Finish when the figure below appears150Mbps Wireless N USB Adapter TL-WN727N150Mbps Wireless N USB Adapter Environmental and Physical Appendix A SpecificationsNormal Appendix B Glossary  Spread Spectrum - Spread Spectrum technology is a wideband radio frequency technique developed by the military for use in reliable, secure, mission-critical communications systems. It is designed to trade off bandwidth efficiency for reliability, integrity, and security. In other words, more bandwidth is consumed than in the case of narrowband transmission, but the trade off produces a signal that is, in effect, louder and thus easier to detect, provided that the receiver knows the parameters of the spread-spectrum signal being broadcast. If a receiver is not tuned to the right frequency, a spread-spectrum signal looks like background noise. There are two main alternatives, Direct Sequence Spread Spectrum DSSS and Frequency Hopping Spread Spectrum FHSS