TP-Link TL-WN727N manual Safety Information

Page 5
Safety Information

射頻電機需忍受合法通信或工業、科學以及醫療用電波輻射性電機設備之干擾。

安全諮詢及注意事項

●請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。 ●清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。 ●注意防潮,請勿將水或其他液體潑灑到本產品上。  ●插槽與開口供通風使用,以確保本產品的操作可靠並防止過熱,請勿堵塞或覆蓋開口。 ●請勿將本產品置放於靠近熱源的地方。除非有正常的通風,否則不可放在密閉位置中。

●請不要私自打開機殼,不要嘗試自行維修本產品,請由授權的專業人士進行此項工作。

Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам нормативних документів та вимогам, що передбачені чинними законодавчими актами України.

Safety Information

When product has power button, the power button is one of the way to shut off the product; when there is no power button, the only way to completely shut off power is to disconnect the product or the power adapter from the power source.

Don’t disassemble the product, or make repairs yourself. You run the risk of electric shock and voiding the limited warranty. If you need service, please contact us.

Avoid water and wet locations.

This product can be used in the following countries:

AT

BG

BY

CA

CZ

DE

DK

EE

 

 

 

 

 

 

 

 

ES

FI

FR

GB

GR

HU

IE

IT

 

 

 

 

 

 

 

 

LT

LV

MT

NL

NO

PL

PT

RO

 

 

 

 

 

 

 

 

RU

SE

SK

TR

UA

 

 

 

 

 

 

 

 

 

 

 

Image 5
Contents Rev 3.2.0 TL-WN727N 150Mbps Wireless N USB AdapterCOPYRIGHT & TRADEMARKS FCC RF Radiation Exposure Statement FCC STATEMENTCanadian Compliance Statement CE Mark WarningIndustry Canada Statement Korea Warning StatementsSafety Information Product Description 150Mbps Wireless N USB Adapter DECLARATION OF CONFORMITYThe product carries the CE Mark Shennan Rd, Nanshan, Shenzhen, ChinaTo connect using WPS CONTENTSTo connect using Windows built-in wireless utility Hardware Overview150Mbps Wireless N USB Adapter Package ContentsTL-WN727N  Note1.1 Introduction 1.2 FeaturesChapter 1 Product Overview Status 1.3 Hardware OverviewWorking Status  Note2.2 Software Installation Chapter 2 Installation2.1 Hardware Installation TL-WN727N 5. Click Install to continue the setup 6. The utility and drivers will install. This may take 1~2 minutes TL-WN727N 3.1 To connect using TWCU Chapter 3 Connect to a Wireless NetworkTo connect using TWCU TP-LINK Wireless Configuration Utility To connect using WPS1 Wireless network of WPA/WPA2-Personal 2 Wireless network of WPA/WPA2-Enterprise 4. Please wait a few minutes for the connection process 3.2.1 PBC Push Button Configuration method 3.2 To connect using WPSTL-WN727N 3.2.2.1. Enter the PIN from your AP device 3.2.2 PIN method3.2.2.2. Enter a PIN into your AP device 2. The adapter will be connecting to the target network3.3.1 In Windows 3.3 To connect using Windows built-in wireless utility3. You have now successfully connected to the network 3.3.2 In Windows Vista 4. You have now successfully connected to the network 3.3.3 In Windows XP 2. Right-click on the wireless computer icon in your system tray lower-right corner. Select View Available Wireless Networks 3.3.4 In Windows 2. If the network is unencrypted, you will directly connect to it  Note 4.1 Profile Chapter 4 ManagementThe following items can be found on the screen 4.1.2 Modify a profile 4.1.3 Delete a profile 4.2 Advanced4.3 About Chapter 5 AP Mode  SoftAP mode Select to enable or disable the function 6.1 In Windows XP/Vista/7 Chapter 6 Uninstall Software6.1.2 Uninstall the driver software from your PC 6.2.1 Uninstall the utility software from your PC 6.2 In Windows4. Click Finish when the figure below appears 6.2.2 Uninstall the driver software from your PCTL-WN727N 150Mbps Wireless N USB AdapterTL-WN727N Environmental and Physical Appendix A SpecificationsNormal Appendix B Glossary  Spread Spectrum - Spread Spectrum technology is a wideband radio frequency technique developed by the military for use in reliable, secure, mission-critical communications systems. It is designed to trade off bandwidth efficiency for reliability, integrity, and security. In other words, more bandwidth is consumed than in the case of narrowband transmission, but the trade off produces a signal that is, in effect, louder and thus easier to detect, provided that the receiver knows the parameters of the spread-spectrum signal being broadcast. If a receiver is not tuned to the right frequency, a spread-spectrum signal looks like background noise. There are two main alternatives, Direct Sequence Spread Spectrum DSSS and Frequency Hopping Spread Spectrum FHSS