TP-Link manual Local Management, TL-WR940N Wireless N Router

Page 66

TL-WR940NWireless N Router

UDP Flood and ICMP-Flood.

¾DoS Protection - Denial of Service protection. Check the Enable or Disable button to enable or disable the DoS protection function. Only when it is enabled, will the flood filters be enabled.

) Note:

Dos Protection will take effect only when the Traffic Statistics in “System Tool → Traffic Statistics” is enabled.

¾Enable ICMP-FLOOD Attack Filtering - Enable or Disable the ICMP-FLOOD Attack Filtering.

¾ICMP-FLOOD Packets Threshold (5~3600) - The default value is 50. Enter a value between 5 ~ 3600. When the current ICMP-FLOOD Packets number is beyond the set value, the Router will startup the blocking function immediately.

¾Enable UDP-FLOOD Filtering - Enable or Disable the UDP-FLOOD Filtering.

¾UDP-FLOOD Packets Threshold (5~3600) - The default value is 500. Enter a value between 5 ~ 3600. When the current UPD-FLOOD Packets number is beyond the set value, the Router will startup the blocking function immediately.

¾Enable TCP-SYN-FLOOD Attack Filtering - Enable or Disable the TCP-SYN-FLOOD Attack Filtering.

¾TCP-SYN-FLOOD Packets Threshold (5~3600) - The default value is 50. Enter a value between 5 ~ 3600. When the current TCP-SYN-FLOOD Packets numbers is beyond the set value, the Router will startup the blocking function immediately.

¾Ignore Ping Packet From WAN Port - Enable or Disable Ignore Ping Packet From WAN Port. The default setting is disabled. If enabled, the ping packet from the Internet cannot access the Router.

¾Forbid Ping Packet From LAN Port - Enable or Disable Forbid Ping Packet From LAN Port. The default setting is disabled. If enabled, the ping packet from LAN cannot access the Router. This function can be used to defend against some viruses.

Click the Save button to save the settings.

Click the Blocked DoS Host List button to display the DoS host table by blocking.

4.9.3 Local Management

Choose menu “Security → Local Management”, you can configure the management rule in the screen as shown in Figure 4-39.The management feature allows you to deny computers in LAN from accessing the Router.

-58-

Image 66

Contents TL-WR940N Wireless N Router Rev 1.1.0COPYRIGHT & TRADEMARKS FCC STATEMENTNational restrictions FCC RF Radiation Exposure StatementCE Mark Warning CountryIndustry Canada Statement Korea Warning StatementsNCC Notice ETSI EN 301 489-1 V1.8.12008& ETSI EN 301 489-17 EN 550222006 +A12007 DECLARATION OF CONFORMITYETSI EN 300 328 V1.7.1 EN 550241998+A12001+A22003 EN 61000-3-22006+A12009+A22009 ENCONTENTS Package ContentsChapter 4.6.5 4.15.1 Package Contents TL-WR940N Wireless N RouterChapter 1.Introduction Flexible Access ControlSimple Installation 1.1 Overview of the Router1.3 Main Features 1.4 Panel Layout1.4.1 The Front Panel TL-WR940N Wireless N Router1.4.2 The Rear Panel Indication¾ RESET 2.3 Connecting the Router Chapter 2.Connecting the Router2.2 Installation Environment Requirements 2.1 System RequirementsFigure 2-1 Hardware Installation of the TL-WR940N Wireless N Router Chapter 3.Quick Installation Guide 3.1 TCP/IP ConfigurationFigure 3-2 Failure result of Ping command Please check the connection following these stepsFigure 3-1 Success result of Ping command 1. Is the connection between your PC and the Router correct?3.2 Quick Installation Guide Figure 3-5 Quick Setup Figure 3-6 Choose WAN Connection TypeFigure 3-7 Quick Setup - PPPoE Figure 3-8 Quick Setup - MAC CloneFigure 3-9 Quick Setup - MAC Clone Figure 3-10 Quick Setup - Static IPNote Dialog z PSK Password - You can enter ASCII or Hexadecimal characters Figure 3-13 Quick Setup - Finish Chapter 4.Configuring the Router 4.1 Login4.2 Status Please refer to 3.2 Quick Installation Guide 4.3 Quick Setup4.4 QSS Figure 4-1 Router StatusI. By PBC Method OneMethod Two Method Three The QSS Configuration Screen of Wireless AdapterTL-WR940N Wireless N Router II. By PIN Method Two Enter the PIN from my Router 4.5 Network 4.5.1 WANadded to the network Figure 4-5 WAN - Dynamic IP Figure 4-6 WAN - Static IP Figure 4-7 WAN - PPPoE Figure 4-8 PPPoE Advanced Settings NSW / ACT - nsw.bigpond.net.au QLD - qld.bigpond.net.au Figure 4-10 L2TP Settings Figure 4-11 PPTP Settings z Dynamic IP - Connections which use dynamic IP address assignment z Static IP - Connections which use static IP address assignmentFigure 4-12 LAN 4.5.2 LAN4.5.3 MAC Clone Figure 4-13 MAC Address Clone4.6 Wireless 4.6.1 Wireless SettingsOnly the PC on your LAN can use the MAC Address Clone function Figure 4-15 Wireless Settings ¾ Mode - Select the desired mode. The default setting is 11bgn mixed 4.6.2 Wireless Security ¾ WPA /WPA2 - Enterprise - It’s based on Radius Server Encryption - You can select either Automatic, or TKIP or AES 4.6.3 Wireless MAC Filtering Figure 4-20 Wireless MAC address Filtering4. Click the Save button to save this entry 4.6.4 Wireless Advanced to access for Filtering Rules4.6.5 Wireless Statistics 4.7.1 DHCP Settings 4.7 DHCPThis page will be refreshed automatically every 5 seconds ¾ Default Domain - Optional. Input the domain name of your network 4.7.2 DHCP Clients List 4.7.3 Address Reservation4.8 Forwarding To Reserve IP addressesTo modify or delete an existing entry To set up a virtual server entry 4.8.1 Virtual Servers4.8.2 Port Triggering Figure 4-31 Add or Modify a Virtual Server EntryTo add a new rule, follow the steps below 4.8.3 DMZ 3. Incoming Port Range cannot overlap each other4.8.4 UPnP To assign a computer or server to be a DMZ server4.9 Security 4.9.1 Basic SecurityFigure 4-37 Basic Security z z z4.9.2 Advanced Security 4.9.3 Local Management 4.9.4 Remote Management Figure 4-39 Local Management4.10Parental Control Figure 4-40 Remote ManagementTo add a new entry, please follow the steps below 7. Click the Save button 4.11Access Control 4.11.1 RuleTo add a new rule, please follow the steps below Figure 4-45 Access Control Rule ManagementFigure 4-46 Add or Modify Internet Access Control Entry 4.11.2 Host Figure 4-47 Host SettingsFigure 4-48 Add or Modify a Host Entry Figure 4-49 Add or Modify a Host Entry4.11.3 Target Figure 4-50 Target SettingsFigure 4-51 Add or Modify an Access Target Entry Figure 4-52 Add or Modify an Access Target Entry4.11.4 Schedule To add a new schedule, follow the steps below4.12 Advanced Routing Figure 4-54 Advanced Schedule SettingsFigure 4-55 Advanced Routing Other configurations for the entries 4.12.1 Static Routing ListTo add static routing entries 4.13Bandwidth Control 4.12.2 System Routing Table4.13.1 Control Settings 4.13.2 Rules List4.14IP & MAC Binding Setting 4.14.1 Binding SettingTo add/modify a Bandwidth Control rule, follow the steps below To find an existing entry, follow the steps below To add IP & MAC Binding entries, follow the steps belowTo modify or delete an existing entry, follow the steps below Figure 4-64 Binding Setting4.14.2 ARP List Figure 4-66 Find IP & MAC Binding EntryFigure 4-67 ARP List 4.15Dynamic DNS 4.15.1 Comexe.cn DDNSTo set up for DDNS, follow these instructions 4.15.2 Dyndns.org DDNS4.15.3 No-ip.com DDNS Figure 4-69 Dyndns.org DDNS Settings4.16System Tools Figure 4-70 No-ip.com DDNS SettingsFigure 4-71 The System Tools menu 4.16.1 Time Settings To set time manuallyTo set Daylight Saving 4.16.2 DiagnosticTo set time automatically 2. The time will be lost if the router is turned offFigure 4-73 Diagnostic Tools 4.16.3 Firmware Upgrade To upgrade the Routers firmware, follow these instructions below4.16.4 Factory Defaults 4.16.5 Backup & Restore4. The Router will reboot after the upgrading has been finished 4.16.6 Reboot 4.16.7 Password 4.16.8 System LogFigure 4-80 System Log Figure 4-81 Mail Account Settings 4.16.9 Statistics Figure 4-82 StatisticsStatistics Table Appendix A FAQ 1. How do I configure the Router to access Internet by ADSL users?3. I want to use Netmeeting, what do I need to do? Figure A-3 MAC CloneFigure A-4 Virtual Servers Figure A-5 Add or Modify a Virtual server Entry Figure A-6 DMZ4. I want to build a WEB Server on the LAN, what should I do? 5. The wireless stations cannot connect to the Router field of the Web browserAppendix B Configuring the PCs 1. Install TCP/IP componentshown in the Figure below ¾ Setting IP address automaticallyNow you have two ways to configure the TCP/IP protocol below Figure B-2¾ Setting IP address manually Figure B-3Figure B-4 General Appendix C SpecificationsWireless Environmental and PhysicalAppendix D Glossary identifying a wireless local area network. For the wireless devices in a network to communicate with each other, all devices must be configured with the same SSID. This is typically the configuration parameter for a wireless PC card. It corresponds to the ESSID in the wireless Access Point and to the wireless network name