TP-Link manual Control Settings, Rules List, TL-WR940N Wireless N Router

Page 82

4.13.1 Control Settings

TL-WR940NWireless N Router

There are two submenus under the Bandwidth Control menu as shown in Figure 4-59.Click any of them, and you will be able to configure the corresponding function. The detailed explanations for each submenu are provided below.

4.13.1 Control Settings

Choose menu “Bandwidth Control → Control Settings”, you can configure the Egress Bandwidth and Ingress Bandwidth in the next screen. Their values you configure should be less than 100000Kbps. For optimal control of the bandwidth, please select the right Line Type and ask your ISP for the total bandwidth of the egress and ingress.

Figure 4-60 Bandwidth Control Settings

¾Enable Bandwidth Control - Check this box so that the Bandwidth Control settings can take effect.

¾Line Type - Select the right type for you network connection. If you don’t know how to choose, please ask your ISP for the information.

¾Egress Bandwidth - The upload speed through the WAN port.

¾Ingress Bandwidth - The download speed through the WAN port.

4.13.2 Rules List

Choose menu “Bandwidth Control → Rules List”, you can view and configure the Bandwidth Control rules in the screen below.

Figure 4-61 Bandwidth Control Rules List

¾Description - This is the information about the rules such as address range.

-74-

Image 82

Contents TL-WR940N Wireless N Router Rev 1.1.0COPYRIGHT & TRADEMARKS FCC STATEMENTNational restrictions FCC RF Radiation Exposure StatementCE Mark Warning CountryKorea Warning Statements Industry Canada StatementNCC Notice ETSI EN 301 489-1 V1.8.12008& ETSI EN 301 489-17 EN 550222006 +A12007 DECLARATION OF CONFORMITYETSI EN 300 328 V1.7.1 EN 550241998+A12001+A22003 EN 61000-3-22006+A12009+A22009 ENPackage Contents CONTENTSChapter 4.6.5 4.15.1 Package Contents TL-WR940N Wireless N RouterChapter 1.Introduction Flexible Access ControlSimple Installation 1.1 Overview of the Router1.4 Panel Layout 1.3 Main Features1.4.1 The Front Panel TL-WR940N Wireless N Router1.4.2 The Rear Panel Indication¾ RESET 2.3 Connecting the Router Chapter 2.Connecting the Router2.2 Installation Environment Requirements 2.1 System RequirementsFigure 2-1 Hardware Installation of the TL-WR940N Wireless N Router Chapter 3.Quick Installation Guide 3.1 TCP/IP ConfigurationFigure 3-2 Failure result of Ping command Please check the connection following these stepsFigure 3-1 Success result of Ping command 1. Is the connection between your PC and the Router correct?3.2 Quick Installation Guide Figure 3-5 Quick Setup Figure 3-6 Choose WAN Connection TypeFigure 3-7 Quick Setup - PPPoE Figure 3-8 Quick Setup - MAC CloneFigure 3-9 Quick Setup - MAC Clone Figure 3-10 Quick Setup - Static IPNote Dialog z PSK Password - You can enter ASCII or Hexadecimal characters Figure 3-13 Quick Setup - Finish 4.1 Login Chapter 4.Configuring the Router4.2 Status Please refer to 3.2 Quick Installation Guide 4.3 Quick Setup4.4 QSS Figure 4-1 Router StatusI. By PBC Method OneMethod Two Method Three The QSS Configuration Screen of Wireless AdapterTL-WR940N Wireless N Router II. By PIN Method Two Enter the PIN from my Router 4.5.1 WAN 4.5 Networkadded to the network Figure 4-5 WAN - Dynamic IP Figure 4-6 WAN - Static IP Figure 4-7 WAN - PPPoE Figure 4-8 PPPoE Advanced Settings NSW / ACT - nsw.bigpond.net.au QLD - qld.bigpond.net.au Figure 4-10 L2TP Settings Figure 4-11 PPTP Settings z Dynamic IP - Connections which use dynamic IP address assignment z Static IP - Connections which use static IP address assignmentFigure 4-12 LAN 4.5.2 LAN4.5.3 MAC Clone Figure 4-13 MAC Address Clone4.6.1 Wireless Settings 4.6 WirelessOnly the PC on your LAN can use the MAC Address Clone function Figure 4-15 Wireless Settings ¾ Mode - Select the desired mode. The default setting is 11bgn mixed 4.6.2 Wireless Security ¾ WPA /WPA2 - Enterprise - It’s based on Radius Server Encryption - You can select either Automatic, or TKIP or AES 4.6.3 Wireless MAC Filtering Figure 4-20 Wireless MAC address Filtering4. Click the Save button to save this entry 4.6.4 Wireless Advanced to access for Filtering Rules4.6.5 Wireless Statistics 4.7 DHCP 4.7.1 DHCP SettingsThis page will be refreshed automatically every 5 seconds ¾ Default Domain - Optional. Input the domain name of your network 4.7.2 DHCP Clients List 4.7.3 Address ReservationTo Reserve IP addresses 4.8 ForwardingTo modify or delete an existing entry To set up a virtual server entry 4.8.1 Virtual Servers4.8.2 Port Triggering Figure 4-31 Add or Modify a Virtual Server EntryTo add a new rule, follow the steps below 4.8.3 DMZ 3. Incoming Port Range cannot overlap each other4.8.4 UPnP To assign a computer or server to be a DMZ server4.9 Security 4.9.1 Basic SecurityFigure 4-37 Basic Security z z z4.9.2 Advanced Security 4.9.3 Local Management 4.9.4 Remote Management Figure 4-39 Local Management4.10Parental Control Figure 4-40 Remote ManagementTo add a new entry, please follow the steps below 7. Click the Save button 4.11Access Control 4.11.1 RuleTo add a new rule, please follow the steps below Figure 4-45 Access Control Rule ManagementFigure 4-46 Add or Modify Internet Access Control Entry 4.11.2 Host Figure 4-47 Host SettingsFigure 4-48 Add or Modify a Host Entry Figure 4-49 Add or Modify a Host Entry4.11.3 Target Figure 4-50 Target SettingsFigure 4-51 Add or Modify an Access Target Entry Figure 4-52 Add or Modify an Access Target Entry4.11.4 Schedule To add a new schedule, follow the steps belowFigure 4-54 Advanced Schedule Settings 4.12 Advanced RoutingFigure 4-55 Advanced Routing 4.12.1 Static Routing List Other configurations for the entriesTo add static routing entries 4.13Bandwidth Control 4.12.2 System Routing Table4.13.1 Control Settings 4.13.2 Rules List4.14.1 Binding Setting 4.14IP & MAC Binding SettingTo add/modify a Bandwidth Control rule, follow the steps below To find an existing entry, follow the steps below To add IP & MAC Binding entries, follow the steps belowTo modify or delete an existing entry, follow the steps below Figure 4-64 Binding SettingFigure 4-66 Find IP & MAC Binding Entry 4.14.2 ARP ListFigure 4-67 ARP List 4.15Dynamic DNS 4.15.1 Comexe.cn DDNSTo set up for DDNS, follow these instructions 4.15.2 Dyndns.org DDNS4.15.3 No-ip.com DDNS Figure 4-69 Dyndns.org DDNS SettingsFigure 4-70 No-ip.com DDNS Settings 4.16System ToolsFigure 4-71 The System Tools menu 4.16.1 Time Settings To set time manuallyTo set Daylight Saving 4.16.2 DiagnosticTo set time automatically 2. The time will be lost if the router is turned offFigure 4-73 Diagnostic Tools 4.16.3 Firmware Upgrade To upgrade the Routers firmware, follow these instructions below4.16.5 Backup & Restore 4.16.4 Factory Defaults4. The Router will reboot after the upgrading has been finished 4.16.6 Reboot 4.16.7 Password 4.16.8 System LogFigure 4-80 System Log Figure 4-81 Mail Account Settings 4.16.9 Statistics Figure 4-82 StatisticsStatistics Table Appendix A FAQ 1. How do I configure the Router to access Internet by ADSL users?Figure A-3 MAC Clone 3. I want to use Netmeeting, what do I need to do?Figure A-4 Virtual Servers Figure A-5 Add or Modify a Virtual server Entry Figure A-6 DMZ4. I want to build a WEB Server on the LAN, what should I do? 5. The wireless stations cannot connect to the Router field of the Web browserAppendix B Configuring the PCs 1. Install TCP/IP componentshown in the Figure below ¾ Setting IP address automaticallyNow you have two ways to configure the TCP/IP protocol below Figure B-2¾ Setting IP address manually Figure B-3Figure B-4 General Appendix C SpecificationsWireless Environmental and PhysicalAppendix D Glossary identifying a wireless local area network. For the wireless devices in a network to communicate with each other, all devices must be configured with the same SSID. This is typically the configuration parameter for a wireless PC card. It corresponds to the ESSID in the wireless Access Point and to the wireless network name