Polycom DOC2559A manual 3RMX 4000 Rack Mount

Page 20

Chapter 1- Hardware Description

3Fasten the RMX to the rack with 8 screws into the holes provided on the RMX’s front as shown in Figure 1-3.

Figure 1-3RMX 4000 Rack Mount

Rack mounting screws must be supplied by the rack’s manufacturer.

The airflow of the RMX 4000 is from right to left. Be sure that the areas on the left and right side of the system are clear for proper

ventilation.

When the unit is installed on a rack, the rack must be properly grounded to the central office ground. The rack must be grounded with two-hole compression- type connectors using copper conductors (tinned or untinned). Wire, bus bar or braided strap connectors are acceptable.

1-14

Image 20

Contents Polycom RMX 4000 Hardware Guide USA Συμμορφωνεται Προσ ΤΙΣ Ουσιωδεισ Απαιτησεισ ΚΑΙ ΤΙΣ Regulatory Notices Table of Contents Component Replacement Hardware Description RMX 4000 Specifications RMX 4000 System Capacities Following table summarizes the different system capacitiesMPMx Resource Capacities Resource Type MPMx S MPMx DMPM+ Resource Capacities MPMx and MPM+ Modes MCU Mode GuidelinesOperating Mode Selection During Startup / Restart Polycom RMX 4000 Hardware Guide Safety Requirements Site Safety RequirementsGeneral Installation Precautions Rack Mount Safety PrecautionsInstalling the RMX Unpacking the RMX Polycom RMX 4000 Hardware Guide Rack Mount Preparations Installing the RMX in a Rack or as a StandaloneStandalone RMX 4000 Installation 2Installing chassis runners and RMX in a rack Placing the RMX 4000 in a 19 Rack3RMX 4000 Rack Mount Placing the RMX 4000 in a 23 Rack 4Removing and attaching 19 and 23 bracketsReverse Mounting the RMX 4000 in a Rack To reverse mount the RMX 4000 on a 19 rackConnecting the RMX 4000 to Power Sources Connecting the RMX 4000 to AC Power Connecting the RMX 4000 to -48DC Selv Power Types of DC Circuit Breakers installed on the RMX Connecting Cables on the RMX To connect the cables AC and DC systems RTM-IPFirst-time Power-up RMX 4000 Components RMX 4000 Front PanelShows the front panel of an RMX 4000 DC system Component Description Component Description RMX 4000 Rear Panel 9RMX 4000 AC Rear ViewRTM-IP 10RMX 4000 DC Rear ViewFollowing items appear on the RMX 4000 rear panel RTM Isdn RTM LAN ISDN/PSTN Clock SourceComponent Slot Allocation AC Power Entry Module PEMDC Power Rail Module RTM ISDN/RTM RMX 4000 LEDs RMX 4000 Front Panel LEDsCard removal Initiated The card Cntl 4000 Unit RMX 4000 Rear Panel LEDs RTM-IPRTM LAN RTM Isdn Hardware Description Component Replacement Component Replacement Using the Modified PMC Compatible Ejector Lever HandleReplacing the Cntl 4000 Module Replacing an AC Power Supply Module Replacing an AC Power Entry Module PEM Replacing a DC Power Rail Module PRM Component Replacement Replacing the Fan Drawer Carefully slide the Fan drawer out through the front panelInserting an Air Filter Optional in the Fan Drawer Replacing an Faulty MPM+/MPMx Card Removing the MPM+/MPMx Card from the MCUComponent Replacement Installing the Replacement MPM+/MPMx Card Installing an MPM+/MPMx Card on the RMX Replacing a RTM Isdn CardPRI Cables Replacing the RTM-IP Replacing the RTM LAN Replacing the Fabric Switch Module FSM Polycom RMX 4000 Hardware Guide