Polycom DOC2559A manual PRI Cables

Page 61

Polycom RMX 4000 Hardware Guide

6On the card to be installed, move the ejector levers to their fully open position.

7Slide in the replacement RTM ISDN card.

8Insert the card into the slot until the ejector levers touch the front edge of the card cage.

9Push the ejector levers to their fully closed position.

10Tighten the captive screws on each side of the rear panel of the card, securing the RTM ISDN card to RMX.

11Connect the RJ-45 terminated PRI cables into any of the slots labeled PRI1 - PRI12:

PRI Cables

7 E1 or 9 T1 cables can be connected to each RTM ISDN card, up to a total of 14 E1 or 18 T1 PRI cables when a maximum of two RTM ISDN cards are installed.

12Turn ON the RMX 4000.

2-15

Image 61

Contents Polycom RMX 4000 Hardware Guide USA Συμμορφωνεται Προσ ΤΙΣ Ουσιωδεισ Απαιτησεισ ΚΑΙ ΤΙΣ Regulatory Notices Table of Contents Component Replacement Hardware Description RMX 4000 Specifications Following table summarizes the different system capacities RMX 4000 System CapacitiesResource Type MPMx S MPMx D MPMx Resource CapacitiesMPM+ Resource Capacities Operating Mode Selection During Startup / Restart MCU Mode GuidelinesMPMx and MPM+ Modes Polycom RMX 4000 Hardware Guide Site Safety Requirements Safety RequirementsRack Mount Safety Precautions General Installation PrecautionsUnpacking the RMX Installing the RMXPolycom RMX 4000 Hardware Guide Standalone RMX 4000 Installation Installing the RMX in a Rack or as a StandaloneRack Mount Preparations Placing the RMX 4000 in a 19 Rack 2Installing chassis runners and RMX in a rack3RMX 4000 Rack Mount 4Removing and attaching 19 and 23 brackets Placing the RMX 4000 in a 23 RackTo reverse mount the RMX 4000 on a 19 rack Reverse Mounting the RMX 4000 in a RackConnecting the RMX 4000 to Power Sources Connecting the RMX 4000 to AC Power Connecting the RMX 4000 to -48DC Selv Power Types of DC Circuit Breakers installed on the RMX To connect the cables AC and DC systems RTM-IP Connecting Cables on the RMXFirst-time Power-up RMX 4000 Front Panel RMX 4000 ComponentsShows the front panel of an RMX 4000 DC system Component Description Component Description 9RMX 4000 AC Rear View RMX 4000 Rear Panel10RMX 4000 DC Rear View RTM-IPFollowing items appear on the RMX 4000 rear panel RTM Isdn ISDN/PSTN Clock Source RTM LANDC Power Rail Module AC Power Entry Module PEMComponent Slot Allocation RTM ISDN/RTM RMX 4000 Front Panel LEDs RMX 4000 LEDsCard removal Initiated The card Cntl 4000 Unit RTM-IP RMX 4000 Rear Panel LEDsRTM LAN RTM Isdn Hardware Description Component Replacement Component Replacement Handle Using the Modified PMC Compatible Ejector LeverReplacing the Cntl 4000 Module Replacing an AC Power Supply Module Replacing an AC Power Entry Module PEM Replacing a DC Power Rail Module PRM Component Replacement Carefully slide the Fan drawer out through the front panel Replacing the Fan DrawerInserting an Air Filter Optional in the Fan Drawer Removing the MPM+/MPMx Card from the MCU Replacing an Faulty MPM+/MPMx CardComponent Replacement Installing the Replacement MPM+/MPMx Card Replacing a RTM Isdn Card Installing an MPM+/MPMx Card on the RMXPRI Cables Replacing the RTM-IP Replacing the RTM LAN Replacing the Fabric Switch Module FSM Polycom RMX 4000 Hardware Guide