Polycom DOC2559A manual Connecting the RMX 4000 to Power Sources

Page 23

Polycom RMX 4000 Hardware Guide

3Place the RMX in a rack and tighten the 8 screws securing the RMX to the rack.

Connecting the RMX 4000 to Power Sources

You can connect either an AC Inlet or to DC power according to the power system required at your site:

•For systems with AC Power, up to three power supplies can be installed with one being redundant (n+1).

•For systems with DC Power, up to two power supplies can be installed with one being redundant (n+1), and each power supply has a built in circuit breaker. With DC power, slot 10 (the center slot) must remain unoccupied.

Follow the steps appropriate specified below for your power system.

The following restrictions apply to the conductors and connectors that may be used to ground the unit when rack mounted:

•When using bare conductors, they must be coated with an appropriate antioxidant compound before crimp connections are made. Tinned, solder-plated or silver-plated connectors do not have to be prepared in this manner.

•The same bolt assemblies should not secure multiple connectors.

1-17

Image 23

Contents Polycom RMX 4000 Hardware Guide USA Συμμορφωνεται Προσ ΤΙΣ Ουσιωδεισ Απαιτησεισ ΚΑΙ ΤΙΣ Regulatory Notices Table of Contents Component Replacement Hardware Description RMX 4000 Specifications Following table summarizes the different system capacities RMX 4000 System CapacitiesResource Type MPMx S MPMx D MPMx Resource CapacitiesMPM+ Resource Capacities MPMx and MPM+ Modes MCU Mode GuidelinesOperating Mode Selection During Startup / Restart Polycom RMX 4000 Hardware Guide Site Safety Requirements Safety RequirementsRack Mount Safety Precautions General Installation PrecautionsUnpacking the RMX Installing the RMXPolycom RMX 4000 Hardware Guide Rack Mount Preparations Installing the RMX in a Rack or as a StandaloneStandalone RMX 4000 Installation Placing the RMX 4000 in a 19 Rack 2Installing chassis runners and RMX in a rack3RMX 4000 Rack Mount 4Removing and attaching 19 and 23 brackets Placing the RMX 4000 in a 23 RackTo reverse mount the RMX 4000 on a 19 rack Reverse Mounting the RMX 4000 in a RackConnecting the RMX 4000 to Power Sources Connecting the RMX 4000 to AC Power Connecting the RMX 4000 to -48DC Selv Power Types of DC Circuit Breakers installed on the RMX To connect the cables AC and DC systems RTM-IP Connecting Cables on the RMXFirst-time Power-up RMX 4000 Front Panel RMX 4000 ComponentsShows the front panel of an RMX 4000 DC system Component Description Component Description 9RMX 4000 AC Rear View RMX 4000 Rear Panel10RMX 4000 DC Rear View RTM-IPFollowing items appear on the RMX 4000 rear panel RTM Isdn ISDN/PSTN Clock Source RTM LANComponent Slot Allocation AC Power Entry Module PEMDC Power Rail Module RTM ISDN/RTM RMX 4000 Front Panel LEDs RMX 4000 LEDsCard removal Initiated The card Cntl 4000 Unit RTM-IP RMX 4000 Rear Panel LEDsRTM LAN RTM Isdn Hardware Description Component Replacement Component Replacement Handle Using the Modified PMC Compatible Ejector LeverReplacing the Cntl 4000 Module Replacing an AC Power Supply Module Replacing an AC Power Entry Module PEM Replacing a DC Power Rail Module PRM Component Replacement Carefully slide the Fan drawer out through the front panel Replacing the Fan DrawerInserting an Air Filter Optional in the Fan Drawer Removing the MPM+/MPMx Card from the MCU Replacing an Faulty MPM+/MPMx CardComponent Replacement Installing the Replacement MPM+/MPMx Card Replacing a RTM Isdn Card Installing an MPM+/MPMx Card on the RMXPRI Cables Replacing the RTM-IP Replacing the RTM LAN Replacing the Fabric Switch Module FSM Polycom RMX 4000 Hardware Guide