Polycom DOC2559A manual Installing an MPM+/MPMx Card on the RMX, Replacing a RTM Isdn Card

Page 60

Chapter 2- Component Replacement

Installing an MPM+/MPMx Card on the RMX 4000

On the RMX 4000 when upgrading from MPM/MPM+ to MPMx on the RTM-IP 4000 all connections require Ferrite cables.

1If applicable, loosen the captive screws and remove the slot cover.

2On the card to be installed, move the ejector levers to their full open position.

3Insert the card into the slot until the ejector levers touch the front edge of the card cage.

4Push the ejector levers to their closed position and tighten the captive screws on each side of the card, securing the MPM+/MPMx card to the RMX.

The blue HS LEDs on the MPM+/MPMx card and the Control Unit start flashing and the power on cycle for the card is initiated:

—The card’s resources are added to the system resources list

—The number of available ports on the RMX is increased to the current CFS license level

—Port usage is re-calculated and the Port Gauges and Video/Voice Port Configuration are updated

When the power on cycle of the MPM+/MPMx card is completed, the blue HS LEDs will turn OFF. The green RDY LED on the MPM+/ MPMx card switches on and remains lit.

Replacing a RTM ISDN Card

1Ensure that the power switch/circuit switch on the RMX 4000 is turned OFF (O).

2Remove the cables connected to the card.

3Unscrew the captive screws that fasten the card to the MCU.

4Remove the RTM ISDN card. Use the metal ejector levers to pull the RTM ISDN card out of its slot in the backplane.

5Carefully slide the RTM ISDN card out through the front panel.

2-14

Image 60

Contents Polycom RMX 4000 Hardware Guide USA Συμμορφωνεται Προσ ΤΙΣ Ουσιωδεισ Απαιτησεισ ΚΑΙ ΤΙΣ Regulatory Notices Table of Contents Component Replacement Hardware Description RMX 4000 Specifications RMX 4000 System Capacities Following table summarizes the different system capacitiesMPMx Resource Capacities Resource Type MPMx S MPMx DMPM+ Resource Capacities MCU Mode Guidelines Operating Mode Selection During Startup / RestartMPMx and MPM+ Modes Polycom RMX 4000 Hardware Guide Safety Requirements Site Safety RequirementsGeneral Installation Precautions Rack Mount Safety PrecautionsInstalling the RMX Unpacking the RMXPolycom RMX 4000 Hardware Guide Installing the RMX in a Rack or as a Standalone Standalone RMX 4000 InstallationRack Mount Preparations 2Installing chassis runners and RMX in a rack Placing the RMX 4000 in a 19 Rack3RMX 4000 Rack Mount Placing the RMX 4000 in a 23 Rack 4Removing and attaching 19 and 23 bracketsReverse Mounting the RMX 4000 in a Rack To reverse mount the RMX 4000 on a 19 rackConnecting the RMX 4000 to Power Sources Connecting the RMX 4000 to AC Power Connecting the RMX 4000 to -48DC Selv Power Types of DC Circuit Breakers installed on the RMX Connecting Cables on the RMX To connect the cables AC and DC systems RTM-IPFirst-time Power-up RMX 4000 Components RMX 4000 Front PanelShows the front panel of an RMX 4000 DC system Component Description Component Description RMX 4000 Rear Panel 9RMX 4000 AC Rear ViewRTM-IP 10RMX 4000 DC Rear ViewFollowing items appear on the RMX 4000 rear panel RTM Isdn RTM LAN ISDN/PSTN Clock SourceAC Power Entry Module PEM DC Power Rail ModuleComponent Slot Allocation RTM ISDN/RTM RMX 4000 LEDs RMX 4000 Front Panel LEDsCard removal Initiated The card Cntl 4000 Unit RMX 4000 Rear Panel LEDs RTM-IPRTM LAN RTM Isdn Hardware Description Component Replacement Component Replacement Using the Modified PMC Compatible Ejector Lever HandleReplacing the Cntl 4000 Module Replacing an AC Power Supply Module Replacing an AC Power Entry Module PEM Replacing a DC Power Rail Module PRM Component Replacement Replacing the Fan Drawer Carefully slide the Fan drawer out through the front panelInserting an Air Filter Optional in the Fan Drawer Replacing an Faulty MPM+/MPMx Card Removing the MPM+/MPMx Card from the MCUComponent Replacement Installing the Replacement MPM+/MPMx Card Installing an MPM+/MPMx Card on the RMX Replacing a RTM Isdn CardPRI Cables Replacing the RTM-IP Replacing the RTM LAN Replacing the Fabric Switch Module FSM Polycom RMX 4000 Hardware Guide