Polycom DOC2559C manual Connecting the RMX 4000 to AC Power

Page 23

Polycom RMX 4000 Hardware Guide

•Listed fastening hardware must be compatible with the materials being joined and must be preclude loosening, deterioration and electrochemical corrosion of the hardware and joint materials.

Connecting the RMX 4000 to AC Power

• Do not connect the green or green-yellow wire to the system single-point ground screw.

• Customers are required to only use AC power cables supplied by Polycom.

• The size of the protective earthing conductor should be a minimum of 10AWG.

• All three outlets intended for connection of the three power cords must be protected with an external overcurrent protection device either in building or in the rack with the rating not higher than 20Amp.

• Do not use an Extension cords with any of the cables.

1 Make sure that the power button is switched OFF on the RMX 4000.

ESD

connector

Ground

connector


Off/On switch		Power Entry Modules

2Insert the power cables into the power connectors on the rear panel of the RMX 4000.

1-17

Image 23

Contents Polycom RMX 4000 Hardware Guide USA Συμμορφωνεται Προσ ΤΙΣ Ουσιωδεισ Απαιτησεισ ΚΑΙ ΤΙΣ Russian Communication Certificate Regulatory NoticesTable of Contents ISDN/PSTN Clock Source MPM+ and MPMx Media Cards RMX 4000 Rear Panel RTM-IPHardware Description Media Protocols Power SupplyPower Consumption PhysicalEnvironment RMX 4000 System CapacitiesConferencing Capacities Following table summarizes the different system capacitiesSystem Functions MPM+ Mode MPMx Mode MPM+ Card Resource Capacities per Card AssemblyMPMx Card MPMx Resource Capacities per Card Type MPM+ and MPMxMaximum Possible Resources Per Card Resource TypeSite Safety Requirements Safety RequirementsRack Mount Safety Precautions General Installation PrecautionsUnpacking the RMX Installing the RMXHardware Description Rack Mount Preparations Installing the RMX in a Rack or as a StandaloneStandalone RMX 4000 Installation Placing the RMX 4000 in a 19 Rack 2Installing chassis runners and RMX in a rack3RMX 4000 Rack Mount 4Removing and attaching 19 and 23 brackets Placing the RMX 4000 in a 23 RackTo reverse mount the RMX 4000 on a 19 rack Reverse Mounting the RMX 4000 in a RackConnecting the RMX 4000 to Power Sources Make sure that the power button is switched OFF on the RMX Connecting the RMX 4000 to AC PowerConnecting the RMX 4000 to -48DC Selv Power Type a Type B Types of DC Circuit Breakers installed on RMXTo connect the cables AC and DC systems RTM-IP Connecting Cables to the RMXRTM LAN on First-time Power-upFor more information about specific card connections, see RMX 4000 Front Panel RMX 4000 Components8shows the front panel of an RMX 4000 DC system Component Description MPM+ and MPMx Media Cards Card Configuration Mode Selection During Startup / Restart9RMX 4000 AC Rear View RMX 4000 Rear Panel10RMX 4000 DC Rear View RTM-IPLAN 3 Cntl Following items appear on the RMX 4000 rear panelStandby button Toggle between CPU activation and standby RTM IsdnISDN/PSTN Clock Source AC Power Entry Module PEMSlot ID/No Card/Component Requirement DC Power Rail ModuleComponent Slot Allocation RTM ISDN/RTM LED Color Description RMX 4000 Front Panel LEDsFollowing items appear on the RMX 4000 front panel ComponentCard Insertion Initiated If during Card removal Initiated The cardCntl 4000 Unit LED Color Description Name RMX 4000 Rear Panel LEDsRTM-IP Following LEDs appear on the RTM-IP 4000 cardFunction Name Following LEDs appear on the RTM LANFollowing LEDs appear on the RTM Isdn RTM IsdnComponent Replacement Component Replacement Handle Using the Modified PMC Compatible Ejector LeverReplacing the Cntl 4000 Module Replacing an AC Power Supply Module Replacing an AC Power Entry Module PEM Replacing a DC Power Rail Module PRM Component Replacement Carefully slide the Fan drawer out through the front panel Replacing the Fan DrawerInserting an Air Filter Optional in the Fan Drawer Removing the MPM+/MPMx Card from the MCU Replacing an Faulty MPM+/MPMx CardComponent Replacement Installing the Replacement MPM+/MPMx Card Replacing the RTM Isdn Card Installing an MPM+/MPMx Card on the RMXPRI Cables Replacing the RTM-IP Replacing the RTM LAN Replacing the Fabric Switch Module FSM Polycom RMX 4000 Hardware Guide