TP-Link TL-R480T+ manual

Page 16

Step 4: Configure the IP address as shown in Figure 3-4.After that, click OK.

Figure 3-4

Note:

You can configure the PC to get an IP address automatically, select “Obtain an IP address automatically” and “Obtain DNS server address automatically” in the screen above. For Windows 98 OS or earlier, the PC and router may need to be restarted.

Now, you can run the Ping command in the command prompt to verify the network connection. Please click the Start menu on your desktop, select run tab, type cmd in the field, and then type ping 192.168.0.1 on the next screen, and then press Enter.

If the result displayed is similar to the screen below, the connection between your PC and the router has been established.

Figure 3-5

If the result displayed is similar to the screen shown below, it means that your PC has not connected to the router.

-10-

Image 16

Contents TL-R480T+ Load Balance Broadband Router Copyright & Trademarks FCC Statement Safety Information 安全諮詢及注意事項Contents Hardware Specifications 119 120Glossary 122 Appendix CPackage Contents Conventions Intended ReadersOverview of this Guide Page Overview of the Router Features  Easy-to-useHardware Basic FunctionsAppearance Front Panel Reset button  AC Power ReceptacleRear Panel  Interface Description PortQuick Installation Guide Configure PCPage Page Is the TCP/IP configuration for your PC correct? LoginIs the connection between your PC and the router correct? WAN Mode 11 WAN Connection Type Page Page 17 Configuration Completed Configuration StatusQuick Setup WAN ModeNetwork 1 WANStatic IP  Static IPDefault Gateway Primary DNSSecondary DNS Upstream BandwidthWAN Dynamic IP Following items are displayed on this screen  Dynamic IPGet IP Address by UnicastUse the following DNS ServerPPPoE WAN PPPoEPassword Active ModeSettings Keep Alive Account NameService Name ISP AddressSecondary Connection Connection Type PPPoE Status L2TP WAN L2TP L2TP Settings Server IPBandwidth Downstream Bandwidth Upstream L2TP Status Pptp  Pptp Settings Secondary Connections Pptp Status  BigPond Settings BigPondPage 2.1 LAN 2 LAN BigPond Status Dhcp  LAN Dhcp Settings Dhcp ClientDhcp Reservation  Dhcp ReservationIptv  List of Reserved AddressSet the MAC Address for LAN port MAC AddressSet the MAC Address for WAN port Switch Statistics MAC Address Port15 Statistics Following items are displayed on this screen  StatisticsPort Mirror  GeneralMode  Port MirrorMirroring Port Mirrored PortRate Control Application Example Port Config Port Config Rate Control Port Status Port VlanGroup User Group Port Vlan User View View Config ViewAdvanced NAT Setup1 NAT  One-to-One NAT One-to-One NAT List of Rules Multi-Nets NAT  Multi-Nets NATApplication Example  Network Requirements  Configuration procedure Virtual Server  Virtual ServerInterface ProtocolPort Triggering  Port Triggering 1.6 ALG  ALGSetup Traffic Control323 ALG IPsec ALGIs available to use  Interface BandwidthGuaranteed Bandwidth ControlDirection GroupSession Limit Session Limit Session Limit Session List List of Session Limit Load Balance ConfigurationPolicy Routing WAN Link Backup 36 Link Backup Following items are displayed on this screen Protocol Routing Static Route Protocol  List of Protocol38 Static Route Following items are displayed on this screen  Static RouteApplication Example  Network Requirements Anti ARP Spoofing FirewallIP-MAC Binding  IP-MAC Binding ARP Scanning 40 ARP ScanningAttack Defense ARP ListPacket Anomaly Flood DefenseDefense Enable Attack MAC FilteringDefense Logs  MAC FilteringAccess Control URL Filtering URL Filtering Rule ObjectAccess Rules Web FilteringService  Access RulesPolicy  List of Rules Service  ServiceName Dest. PortApp Control  List of ServiceControl Rules  Control Rules DatabaseApplication PPPoE Server ServicesGeneral Page IP Address Pool Account IP Address Pool  List of IP Pool52 Account Following items are displayed on this screen  Account Account NameExceptional IP Is 48. If Enable Advanced Account Features is not selected, List of Account  Exceptional IP List of Account List of Exceptional IP Bulletin IntervalEnable Logs ContentDynamic DNS TitleDynDNS 56 DynDNS Ddns Dyndns Ddns No-IP List of DynDNS Account 57 NO-IP Ddns Following items are displayed on this screen  No-IP DdnsPeanutHull  List of No-IP Account PeanutHull Ddns Comexe List of PeanutHull Account 59 Comexe Ddns Following items are displayed on this screen  Comexe Ddns List of Comexe Account UPnP List of UPnP Mapping Maintenance Admin SetupAdministrator  AdministratorLogin Parameter Remote Management Factory Defaults ManagementExport and Import  Remote ManagementReboot  Configuration Version Export  ImportFirmware Upgrade Snmp68 Snmp Following items are displayed on this screen Statistics Interface Traffic StatisticsIP Traffic Statistics Interface Displays the interface IP Fragment RxDiagnostics Diagnostics Traffic Statistics  IP Traffic Statistics71 Diagnostics Following items are displayed on this screen  PingOnline Detection  TracertDetecting PingTime Time List of WAN status  Current TimeDaylight Saving Time Get UTCManual Synchronize withPredefined Mode Recurring ModeDate Mode Logs List of Logs SeveritySend System Logs Level Description Filter Setting NAT TableLevel Description Debugging  NAT TablePage Power PortsTransmission Medium LEDsAppendix B FAQ Page Appendix C Glossary Glossary DescriptionAllows dissimilar communication devices to communicate Port or device that connects to a LAN. Other devices Glossary Description

Related manuals

Manual 95 pages 2.83 Kb