ZyXEL Communications IES-5005 IES-5000/5005/6000 Support Notes Ring Topology Application, Network

Page 77

IES-5000/5005/6000 Support Notes

IES-5000/5005/6000 Support Notes

Ring Topology Application

A ring topology provides network redundancy. This means that when a link is down, the entire network can still be up as traffic is forwarded through another route or gateway. However, to prevent network loops in a ring topology, you must enable RSTP/STP on the network. The following figure shows a ring network example.

ADSL/SHDSL

modem

		Network
	PC	switch	IES-5000
		Port1	IES-5000
		Port2	ALC-1248G
		Uplink1	ALC-1248G
	IES2000	Uplink1	SLC-1248G
	IES2000	Uplink1	SLC-1248G
		Uplink2	ADSL/SHDSL
		Uplink2	ADSL/SHDSL
			modem
	PC		PC

Setting up a Ring Environment

This section shows you how to set up a ring network using an IES-5000, IES-2000 and an ES-4024 switch. The computers should be able to connect to each other even though an uplink connection is down. The following sections describes the configuration steps in detail.

1. IES-5000 settings

1.1 Activating Spanning Tree protocol on Ethernet Ports

Before you set up the ring topology, enable spanning tree protocol on the Ethernet

76

All contents copyright (c) 2008 ZyXEL Communications Corporation.

Image 77

Contents Support Notes Integrated Ethernet SwitchIES-5000/5005/6000 INDEX IES-5000/5005/6000 Support NotesTriple Play Triple play Application with VLC Line CardApplication Notes Triple Play scenario topology P-870H-51 Hardware connectionsIES-5000M Main Chassis MSC1000GIES-5000 Firmware versionsHow to set the P-870H-51 to factory-default? Configure the P-870H-511. System login Configure the IES-50002. Configure the VLC1348G-51 a. Click Port VDSL Sub-step 1 Open VLAN setup page Sub-step 2 Join VLAN 100 to VDSL port Sub-step 3 Join VLAN 500 to VDSL port IES-5000/5005/6000 Support Notes 3. Configure the MSC1000G a. Click VLAN VLAN d. Check the final VLAN setup status of the MSC1000G 4. Use ACL rule to replace the VID / Priority for the PPPoE packets a. Loginb. ACL-rule profile CLI syntax 1 Create ACL profiles 5. Use MVR to configure the IPTV setting on MSC1000G a. Login 6. Configure the IGMP-Proxy and Static Query VLAN a. Login d. Check the Query VLAN status 2. If setting is successful, result is as below 7. Save configuration for the IPDSLAMConfigure the ES-2024A 2. Configure VLANs 2. VLAN 500 for VoIP 3. VLAN 700 for IPTV 4. Check final status of the VLAN settings 1. Click Advance Application VLAN, then choose the VLAN Port Setting c. Set the default PVID for the relative ports in this scenarioDon’t forget to click Apply to save the settings 2.Set port 1 / 5 / 7’s PVID as 100 / 500 / 700 as below2. Click Apply at bottom to save the settings 1. Click Basic Setting Port Setup to call the page belowe. Save all the settings for the ES-2024A IES-5000 SLC-1248G or ALC-1248G Setting up Multiple PVCsTriple play Application with ALC/SLC Line Card 1. IES-5000 Settings 2. Prestige 660R-61P791 Settings 3.1 VALN 3. ES-2024 settingsIES-5000/5005/6000 Support Notes Set the PVIDs on port 1 and 2 to 10 and 20 respectively 3.2 PVID setupIES-5000/5005/6000 Support Notes IES‐5000 Slot VLC1348G‐51 IES-5000/5005/6000 Support Notes VDSL2 to ADSL2+ FallbackP‐660H‐61 ADSL2+ CPE1. Telnet into the P-660H-61 Configure the P-660H-61a. Enter 1 in the Main Menu to open Menu 1 - General Setup 2. General Setupb. Type a name in the System Name field c. Select No in the Route IP field d. Select Yes in the Bridge fieldb. Enter 1 to configure the remote node of MyISP ISP, SUA 3. Remote Node Setupa. Enter 11 in the Main Menu to open Menu 11 - Remote Node Setup f. Select LLC-based in the Multiplexing field c. Menu 11.1 - Remote Node Profile appearse. Select RFC 1483 in the Encapsulation field l. Press ENTER to confirm your changes j. Menu 11.6 - Remote Node ATM Layer Options appears1. Login Configure the VLC1348G-51IES-5000/5005/6000 Support Notes c. Select Enable 2. VDSL Port Setupa. Click Port VDSL e. Click Apply3. PVC Setup a. Click Config Save on the navigation panel 4. Config save5. Check status a. Click Statistics Port Statistics c. Click Diagnostic Loopbackd. Select port e. Type 8 in VPI and 35 in VCI f. Click the Test button to perform an OAM F5 loopback test on portIES-5000/5005/6000 Support Notes IES-5000/5005/6000 Support Notes Impulse Noise Protection INP PSD f PSD f IES-5000/5005/6000 Support Notes Upstream Power Back-Off UPBOWhat is UPBO? Non-FEXT dominated environment Do not apply UPBO Modes of UPBOFEXT-dominated environment 1. Protection of the long loop3. Improved performance of short loops 4. Spectral mask compatibility with other servicesMethods of UPBO What is CFM? IES-5000/5005/6000 Support Notes 802.1ag CFMMA--Maintenance Association MD--Maintenance DomainMEP--Maintenance End point CFM TermsMIP--Maintenance Intermediate Point 1. CFM MD Screen WEB GUI Introduction2. CFM MA Screen 3. CFM MEP Screen 4. Loopback Diagnosis Enable CFM CLI Command IntroductionDisable CFM MSC1000Gswtichcfm disable Create a MD Create a MEP MSC1000G switch cfmmep setIES-5000/5005/6000 Support Notes Configuring and applying the profiles to subscriber ports Setting up different DSL port speeds to different subscribersInternet IES-5000 ALC-1248G2. Prestige 660R-61 2.3 Menu11.1 Remote Node Profile 2.1 Menu 1 General Setup2.2 Menu 4 Internet Access Setup 2.4 Menu11.6 Remote Node ATM Layer Options Setting up a VLAN IES-5000/5005/6000 Support Notes Configuring 802.1Q VLAN1.1 VLAN settings 1.2 PVID settingsTGE1 switch port pvid up1 TGE1 switch port pvid up2 802.1x ApplicationAuthenticator Authorized Authentication Server RADIUSSetting up 1. Authenticator Setup IES-50002.2 Create a User Account 2. RADIUS Setup Vantage2.1 RADIUS server setup 3. Supplicant Setup Windows XP IES-5000/5005/6000 Support Notes Please refer to the procedures described in the previous application 4. Prestige 660R-61 SettingsSyslog Server Application Network Setting up a Syslog server1. Installing and Running Kiwi’s Syslog Server 2. IES-5000 settings 1. IES-5000 settings Setting up a Ring EnvironmentIES-5000/5005/6000 Support Notes Ring Topology Application 1.1 Activating Spanning Tree protocol on Ethernet Ports2.2 Activating Spanning Tree protocol on Ethernet ports 2. Setup IES-2000 2.1 Activating Spanning Tree protocolports 1 and 2. The following shows the CLI commands CI command TGE1 sys sw rstp enable TGE1 sys sw rstp port enableSelect Rapid Spanning Tree Protocol to enable it on the port Click Uplink2 to configure this portIES-5000/5005/6000 Support Notes 3. ES-4024 Settings 3.1 Activating Spanning Tree protocol 4. Status Results IGMP IGMP Snooping/IGMP Filtering ApplicationEthernet Port Router1.2 Setting up IGMP Filtering Setting up IGMP snooping/IGMP filtering1. IES-5000 settings 1.1 Activating IGMP Snooping 1. IES-5000 settings 1.1 Configuring MAC filter Limiting Internet access to users on specific DSL portsSetting up MAC Filter/Port Security DHCP Relay Option 82 Application 1.2 Configuring Port SecurityADSL/SHDSL CPE DHCP Client Setting up DHCP Relay OptionNetwork DHCP Server 3. IP Commander settings 2. CPE settingsIES-5000/5005/6000 Support Notes Enter a name and description for the new rule IES-5000/5005/6000 Support Notes Select DHCP Option in the Keywords field IES-5000/5005/6000 Support Notes In the next wizard screen, click Next to continue IES-5000/5005/6000 Support Notes Click Finish to complete the wizard setup After the configuration, your computer should obtain an IP address of 192.168.1.201 from the DHCP server once the computer is connected to the network Packet Filtering1. IES-5000 settings ALC-1248G/SLC 1248G Setting up Packet FilteringNetwork Client Client7- 4 accept-all 7- 5 accept-all 7- 6 accept-all 7- 7 accept-all 7-46 accept-all 7-47 accept-all 7-48 accept-all TGE1 7-42 accept-all 7-43 accept-all 7-44 accept-all 7-45 accept-all