ZyXEL Communications IES-6000 PVID settings, IES-5000/5005/6000 Support Notes, IES-5000 Settings

Page 68

IES-5000/5005/6000 Support Notes

on the IES-5000, another VLAN (to which the two ports are a member of) need to be configured.

1.IES-5000 Settings

1.1 VLAN settings

Create a VLAN group with VID 10 and set Port 1, ENET1 and ENET2 to be members of this VLAN.

CI command:

TGE1> vlan set 10 up1 fix untag

TGE1> vlan set 10 up2 fix untag

TGE1> vlan name 10 VLAN10

TGE1> port pvc vlan 7-1-0/33 10 join untag

Create a VLAN group with VID 20 and set Port 2, ENET1 and ENET2 to be members of this VLAN.

CI command:

TGE1> vlan name 20 VLAN20

TGE1> vlan set 20 up1 fix untag

TGE1> vlan set 20 up2 fix untag

TGE1> port pvc vlan 7-2-0/33 20 join untag

Create a VLAN group with VID 200 and set slot 7, Port 1, Port 2, ENET1 and ENET2 to be members of this VLAN.

CI command:

TGE1> vlan name 200 VLAN200

TGE1> vlan set 200 up1 fix untag

TGE1> vlan set 200 up2 fix untag

TGE1> port pvc vlan 7-1-0/33 200 join untag

TGE1> port pvc vlan 7-2-0/33 200 join untag

1.2 PVID settings

After creating the three VLANs, you need to set the PVID on the ports.

67

All contents copyright (c) 2008 ZyXEL Communications Corporation.

Image 68

Contents Support Notes Integrated Ethernet SwitchIES-5000/5005/6000 IES-5000/5005/6000 Support Notes INDEXTriple Play Triple play Application with VLC Line CardApplication Notes Triple Play scenario topology Hardware connections P-870H-51IES-5000M Main Chassis MSC1000GFirmware versions IES-5000Configure the P-870H-51 How to set the P-870H-51 to factory-default?Configure the IES-5000 1. System login2. Configure the VLC1348G-51 a. Click Port VDSL Sub-step 1 Open VLAN setup page Sub-step 2 Join VLAN 100 to VDSL port Sub-step 3 Join VLAN 500 to VDSL port All contents copyright c 2008 ZyXEL Communications Corporation 3. Configure the MSC1000G a. Click VLAN VLAN d. Check the final VLAN setup status of the MSC1000G a. Login 4. Use ACL rule to replace the VID / Priority for the PPPoE packetsb. ACL-rule profile CLI syntax 1 Create ACL profiles 5. Use MVR to configure the IPTV setting on MSC1000G a. Login 6. Configure the IGMP-Proxy and Static Query VLAN a. Login d. Check the Query VLAN status 7. Save configuration for the IPDSLAM 2. If setting is successful, result is as belowConfigure the ES-2024A 2. Configure VLANs 2. VLAN 500 for VoIP 3. VLAN 700 for IPTV 4. Check final status of the VLAN settings c. Set the default PVID for the relative ports in this scenario 1. Click Advance Application VLAN, then choose the VLAN Port SettingDon’t forget to click Apply to save the settings 2.Set port 1 / 5 / 7’s PVID as 100 / 500 / 700 as below1. Click Basic Setting Port Setup to call the page below 2. Click Apply at bottom to save the settingse. Save all the settings for the ES-2024A IES-5000 SLC-1248G or ALC-1248G Setting up Multiple PVCsTriple play Application with ALC/SLC Line Card 1. IES-5000 Settings 2. Prestige 660R-61P791 Settings 3. ES-2024 settings 3.1 VALNAll contents copyright c 2008 ZyXEL Communications Corporation 3.2 PVID setup Set the PVIDs on port 1 and 2 to 10 and 20 respectivelyAll contents copyright c 2008 ZyXEL Communications Corporation IES-5000/5005/6000 Support Notes VDSL2 to ADSL2+ Fallback IES‐5000 Slot VLC1348G‐51P‐660H‐61 ADSL2+ CPEConfigure the P-660H-61 1. Telnet into the P-660H-612. General Setup a. Enter 1 in the Main Menu to open Menu 1 - General Setupb. Type a name in the System Name field c. Select No in the Route IP field d. Select Yes in the Bridge fieldb. Enter 1 to configure the remote node of MyISP ISP, SUA 3. Remote Node Setupa. Enter 11 in the Main Menu to open Menu 11 - Remote Node Setup f. Select LLC-based in the Multiplexing field c. Menu 11.1 - Remote Node Profile appearse. Select RFC 1483 in the Encapsulation field j. Menu 11.6 - Remote Node ATM Layer Options appears l. Press ENTER to confirm your changesConfigure the VLC1348G-51 1. LoginAll contents copyright c 2008 ZyXEL Communications Corporation 2. VDSL Port Setup c. Select Enablea. Click Port VDSL e. Click Apply3. PVC Setup 4. Config save a. Click Config Save on the navigation panelc. Click Diagnostic Loopback 5. Check status a. Click Statistics Port Statisticsd. Select port e. Type 8 in VPI and 35 in VCI f. Click the Test button to perform an OAM F5 loopback test on portAll contents copyright c 2008 ZyXEL Communications Corporation IES-5000/5005/6000 Support Notes Impulse Noise Protection INP PSD f PSD f IES-5000/5005/6000 Support Notes Upstream Power Back-Off UPBOWhat is UPBO? Modes of UPBO Non-FEXT dominated environment Do not apply UPBOFEXT-dominated environment 1. Protection of the long loop3. Improved performance of short loops 4. Spectral mask compatibility with other servicesMethods of UPBO IES-5000/5005/6000 Support Notes 802.1ag CFM What is CFM?MD--Maintenance Domain MA--Maintenance AssociationMEP--Maintenance End point CFM TermsMIP--Maintenance Intermediate Point WEB GUI Introduction 1. CFM MD Screen2. CFM MA Screen 3. CFM MEP Screen 4. Loopback Diagnosis CLI Command Introduction Enable CFMDisable CFM MSC1000Gswtichcfm disable Create a MD Create a MEP MSC1000G switch cfmmep setAll contents copyright c 2008 ZyXEL Communications Corporation Setting up different DSL port speeds to different subscribers Configuring and applying the profiles to subscriber portsInternet IES-5000 ALC-1248G2. Prestige 660R-61 2.3 Menu11.1 Remote Node Profile 2.1 Menu 1 General Setup2.2 Menu 4 Internet Access Setup 2.4 Menu11.6 Remote Node ATM Layer Options IES-5000/5005/6000 Support Notes Configuring 802.1Q VLAN Setting up a VLAN1.2 PVID settings 1.1 VLAN settings802.1x Application TGE1 switch port pvid up1 TGE1 switch port pvid up2Authentication Server RADIUS Authenticator AuthorizedSetting up 1. Authenticator Setup IES-50002.2 Create a User Account 2. RADIUS Setup Vantage2.1 RADIUS server setup 3. Supplicant Setup Windows XP All contents copyright c 2008 ZyXEL Communications Corporation Please refer to the procedures described in the previous application 4. Prestige 660R-61 SettingsSyslog Server Application Network Setting up a Syslog server1. Installing and Running Kiwi’s Syslog Server 2. IES-5000 settings Setting up a Ring Environment 1. IES-5000 settingsIES-5000/5005/6000 Support Notes Ring Topology Application 1.1 Activating Spanning Tree protocol on Ethernet Ports2. Setup IES-2000 2.1 Activating Spanning Tree protocol 2.2 Activating Spanning Tree protocol on Ethernet portsports 1 and 2. The following shows the CLI commands CI command TGE1 sys sw rstp enable TGE1 sys sw rstp port enableClick Uplink2 to configure this port Select Rapid Spanning Tree Protocol to enable it on the portAll contents copyright c 2008 ZyXEL Communications Corporation 3. ES-4024 Settings 3.1 Activating Spanning Tree protocol 4. Status Results IGMP Snooping/IGMP Filtering Application IGMPEthernet Port Router1.2 Setting up IGMP Filtering Setting up IGMP snooping/IGMP filtering1. IES-5000 settings 1.1 Activating IGMP Snooping 1. IES-5000 settings 1.1 Configuring MAC filter Limiting Internet access to users on specific DSL portsSetting up MAC Filter/Port Security 1.2 Configuring Port Security DHCP Relay Option 82 ApplicationADSL/SHDSL CPE DHCP Client Setting up DHCP Relay OptionNetwork DHCP Server 2. CPE settings 3. IP Commander settingsAll contents copyright c 2008 ZyXEL Communications Corporation Enter a name and description for the new rule All contents copyright c 2008 ZyXEL Communications Corporation Select DHCP Option in the Keywords field All contents copyright c 2008 ZyXEL Communications Corporation In the next wizard screen, click Next to continue All contents copyright c 2008 ZyXEL Communications Corporation Click Finish to complete the wizard setup Packet Filtering After the configuration, your computer should obtain an IP address of 192.168.1.201 from the DHCP server once the computer is connected to the networkSetting up Packet Filtering 1. IES-5000 settings ALC-1248G/SLC 1248GNetwork Client Client7- 4 accept-all 7- 5 accept-all 7- 6 accept-all 7- 7 accept-all 7-42 accept-all 7-43 accept-all 7-44 accept-all 7-45 accept-all 7-46 accept-all 7-47 accept-all 7-48 accept-all TGE1