Lindy MC5-IP manual To connect a computer system, Access Module, Category 5, 5e or Cable from CAM

Page 13
COMPUTER
SYSTEM

Computer system (via CAM)

Each computer system is connected to the MC5 unit via a Computer Access Module (CAM) and standard category 5, 5e or 6 cabling. CAMs are available in various formats to suit differing computer system types and their particular connector styles.

LOCAL

REMOTE

GLOBAL

USER

USER

USER

 

U S

IP

POWER

 

MODEM

IN

 

/ISDN

CAM

 

 

 

 

POWER

 

 

SWITCH

4Attach the connector of the cable run to the socket of the CAM.

Green indicator - power present

Yellow indicator - signal activity

Computer



To connect a computer system

1Ensure that power is disconnected from the MC5 unit and the system to be connected.

(Note: If it is not possible to switch off devices prior to connection, then a ‘Hot plug’ procedure is available – see the Hot plugging and mouse restoration section for more details).

2Locate the required CAM (there are five types available) and attach its video, keyboard and mouse (PS/2-style, USB or Sun) and optional audio connectors to the relevant sockets on the computer system.

Access

Module

 

Note: CAMs derive power from the

Category 5, 5e or 6 cable

computer system via either the PS/2-style

to MC5

keyboard connector, USB or SUN connector.



A range of different connector combinations are made available across the five available CAM formats

USB keyboard/mouse

Sun keyboard/mouse

PS/2-style mouse

PS/2-style keyboard

Audio

Video

5At the other end of the cable run, attach the cable connector to one of the sockets labelled COMPUTER CONNECTIONS on the rear panel of the MC5 unit.

 

Note: Each CAM is

 

specifically shaped so

 

that it can be secured

MC5 rear panel

using a cable tie around

its middle. In this way,

 

 

two CAMs can also be

 

neatly joined together,

 

back-to-back.

 

3Lay a suitable length of category 5, 5e or 6 cabling between the computer system and the MC5 unit. The maximum length of the cable can be up to 50 metres (160 feet), however, bear in mind that the overall distance between any remote user and any computer must not exceed 300 metres (980 feet).

Overall maximum length between any remote user and any host system must not exceed 300 metres (980 feet)

REMOTE

U S

CAM

COMPUTER

USER

 

 

SYSTEM

 

300 metres (980 feet)

50 metres

 

 

maximum

(160 feet)

 

 

 

maximum

 

Category 5, 5e or 6

cable from CAM

6Where necessary use the in-built video compensation feature of the MC5 unit to eliminate any effects caused by the cable run. See Computer video compensation for details.



12

Page 12 Page 14
Image 13
Page 12 Page 14
Contents  MC5-IP KVM SwitchContents Further information Index   Local user One user can be connected directly to the MC5Many computers CAM formatsIndicators MC5 features front and rearPower control port Upgrade port Modem port IP models only Front panel buttonsSwitc What’s in the box What you may additionally needRack brackets Mounting   ConnectionsTo connect the local user port Local userMC5 rear panel Cable lengths for remote user locations Remote user via User StationTo connect a remote user To connect the Global user IP network port Global user IP network portIP network link To connect a computer system Access ModuleCategory 5, 5e or Cable from CAM To connect a modem or Isdn adapter Modem/ISDN portMC5 rear panel Cable from modem Or Isdn adapter To connect the power supply Power in connectionOutput lead from Power adapter To connect and address the switch boxes Power control portSee also Cascading multiple unitsCascade tree How cascade connections operate 43 41 Addressing computers in a cascadeTips for successful cascading Connecting MC5 units in cascadeTo connect units in cascade Testing specific links to cascaded computers Using cascaded computersTo test a specific link Slave MC5 Multiple video head connectionsMaster MC5 Slave monitor Master monitorOverall initial configuration ConfigurationTo access the configuration menu local and remote users Configuration menusTo access the configuration menu global users HotkeysConfiguration menus layout General security and configuration stepsTo enable general security To set an Admin passwordRegistering users edit user list Access to all computers Press Access to no computers PressTo create/edit user accounts Cross markers indicate whichRegistering computers edit computer list Tips when creating/editing computer entriesTo create/edit computer entries Video compensation See Remote user skew adjustment for detailsTo apply computer video compensation Computer video compensationCompensation will not be applied Currently selected cable lengthTo display a suitable high contrast image Remote user video compensationTo apply remote user video compensation If the image controls cannot provide a crisp imageTo use skew adjustment Remote user skew adjustmentUsing the supplied skew pattern Creating a skew test patternConfiguration mode and permanently save all settings Autoscanning To select an autoscan modeTo select an autoscan period To define an autoscan listPreparations for configuration save/load Saving and restoring configuration settingsTo reset MC5 models What to do if the Admin password has been forgottenTo reset the MC5-IP models To restore mouse operation when hot plugging Which restore setting do I use?Hot plugging and mouse restoration Recognising an IntelliMouse-style mouseTo use the initial IP-configuration sequence Initial IP configurationTo configure IP-specific settings To configure IP details from a global user location IP configuration by global userMC5-IP encryption settings Encryption settingsViewer encryption settings Positioning the MC5-IP in the network Networking issues   Placing the MC5-IP behind a router or firewall Port settingsAddressing Firewall/router addressDNS addressing To discover a DHCP-allocated IP addressEnsuring sufficient security Placing the MC5-IP alongside the firewallPorts Power control sequences Power switching configurationTo configure the power sequences for each host computer To control two or more ports simultaneouslyKvmadmin command ip address parameters Kvmadmin utilityKvmadmin -getconfig kvm1.cfg Kvmadmin -setusers users.csvItems required to use the upgrade utility Performing upgradesUpgrading MC5 models and CAMs To use the KVM Firmware Uploader utilitySelect the upgrade file to be used Select the items to be upgradedWhere Vxxx is the upgrade file version number Commence the upgradeUpgrading MC5-IP models To upgrade MC5-IP modelsFront panel controls Accessing the MC5MC5 models MC5-IP modelsTo gain access as a local or remote user Local and remote user accessTo select a computer using the front panel controls Selecting a computerStandard hotkeys To select a computer using hotkeysAbove or for even longer cascaded computers Keep Pressed down until all other Numbers have been enteredTo select a computer using mouse buttons To select a computer using the on-screen menuTo select a computer using mouse buttons Advanced method Selecting cascaded computers Logging in and outConfirmation box To use the Routing status feature To change banner colours or disable the bannerReminder banner Routing statusTo switch a computer on or off Power switching via configuration menuUser preferences and functions Global user access To access via the VNC viewer Global user access via VNC viewerTo download the VNC viewer 1 Open your Web browser Enter the MC5 address here and click OKTo access via your web browser Global user access via web browserWhen using the viewer window Using the viewer windowMenu bar Mouse pointers ConfigureTo select a host Power switching via viewer Access mode shared/privateAuto calibrate Re-synchronise mouseControls Single Mouse ModeMouse Control Resync MouseWhen entering codes KVM switch menuVideo Settings Keyboard Control InfoIncreased by 50% when a slow link is detected Using automatic configurationsDetect such noise and adjust the threshold accordingly Setting the Threshold manuallyIf you need to enter a port number Access via dial up modem or Isdn linkTo initiate a dial up link To enter a port number in a Web browserSupported web browsers Viewer encryption settingsWindows LinuxGetting assistance TroubleshootingTo access the configuration menus Appendix 1 Configuration menusFunctions User Preferences Autoscan Mode Mouse SwitchingGlobal Preferences Screen SaverOSD Dwell Time User TimeoutRS232 Mouse Type Mouse TypeKeypads Controls Setup OptionsLanguage Exclusive UseAutomatic Logout DDC Refresh Settings AT START, Disabled DDC Source Settings AUTO, LOCAL, DefaultAdvanced Options DDC OptionsUnit Configuration Configure IP portUnit Name Time and DateNetwork Configuration Reset Configuration Modem ConfigurationWhat is IP access control? Clearing IP access controlTo clear IP access control To access the remote configuration pages Appendix 2 Configuration pages via viewerMain configuration Logged on users User accounts Admin Password Unit configurationHardware Version Firmware VersionAdvanced unit configuration Time & date configuration IP Access Control Network configurationMAC address IP Network MaskTo define a new IP access control entry Setting IP access controlTo reorder access control entries To edit/remove access control entriesPower control port Serial port configurationModem port Erase Host Configuration Host configurationAdd entry for unrecognised host To create a new host entryPort Direct Port/host addressing using Port DirectExamples To copy and paste the log Logging and statusSyslog Server IP Address For further details To get hereColour/Encoding Click here to access the optionsAuto select Preferred encodingDisable all inputs view-only mode Enable all inputsInputs CustomiseMisc ScalingDefaults Save Defaults ReloadIdentities Load / SaveAppendix 4 VNC viewer window options Encoding and colour level Appendix 5 Browser viewer optionsSecurity IP addresses Appendix 6 Addresses, masks and portsNet masks Inside a bit-wise and function Net masks the binary explanationBinary equivalent Binary octet afterSingle locations Calculating the mask for IP access controlAll locations Address rangesPorts Security issues with portsRouter/firewall address RS232 serial flash upgrade cable Power switch to power switch daisy chain cable6pin mini-DIN Female 9pin D-type FemaleSLAVE2 end 9pin D-type male Multi-head synchronisation cablePermissible key presses Appendix 8 Hotkey sequence codesCreating macro sequences Appendix 9 Supported video modes Safety information WarrantySafety considerations when using power switches with MC5 General Public License LinuxEnd user licence agreement European EMC directive 89/336/EEC Radio Frequency EnergyFCC Compliance Statement United States Germany France Italia USAIndex 109 110

MC5-IP specifications

The Lindy MC5-IP is an innovative and versatile presentation switcher designed for a variety of audiovisual settings, making it ideal for professional environments such as conferences, classrooms, and event spaces. Its primary objective is to provide seamless connectivity and efficient management of multiple video sources, enhancing the overall user experience in presentations and broadcasts.

One of the standout features of the MC5-IP is its capability to handle multiple input formats. It supports HDMI, DisplayPort, and VGA connections, allowing users to easily switch between various devices such as laptops, projectors, and media players. This flexibility promotes a smooth transition during presentations, minimizing downtime and interruptions.

The device is equipped with cutting-edge video processing technology, which ensures high-quality output at resolutions up to 4K. This high definition support is crucial in today’s digital landscape, as it provides crystal-clear images and vibrant colors, essential for impactful presentations. Furthermore, the MC5-IP employs advanced scaling technology that adjusts the output resolution to match the capabilities of the connected display, ensuring optimal visual quality.

Integration capabilities are another highlight of the MC5-IP. It can be easily integrated into existing AV systems and works seamlessly with popular control systems, such as Crestron and AMX. This compatibility allows for centralized control, making it easier for operators to manage video sources, adjust settings, and coordinate multiple displays without the need for complex setups.

In addition, the Lindy MC5-IP features an intuitive user interface that simplifies operation. The device can be controlled via a touch screen, remote control, or web-based application, providing users with convenient options to manage their presentations. The user-friendly design minimizes the learning curve, making it accessible for individuals who may not be tech-savvy.

The MC5-IP also prioritizes reliability and durability. It is built with high-quality components that ensure long-term performance, making it a dependable choice for frequently used environments. Finally, its compact form factor allows for easy transport and installation, catering to the dynamic needs of modern presentation scenarios.

In summary, the Lindy MC5-IP is a robust presentation switcher designed with professionalism in mind. Its versatility, high-resolution support, integration options, user-friendly interface, and durability make it an essential tool for anyone looking to enhance their AV presentations.
Top Page Image Contents