Lindy 25010 user manual 2.6.3 802.1Q VLAN Config

Page 23

2.6.3 802.1Q VLAN Config

2.6.3 802.1Q VLAN Config

The following figure is the page to add/delete/edit the 802.1q VLAN entry. Each VLAN entry has 3 parameters, VID, Tag Members and UnTag Members to be assigned.

After selecting Create New VLAN the figure shown as below will be displayed:

¾VID – a unique VLAN ID. The range is from 1 to 4094

¾Tag Members & UnTag Members – Click the image directly, it will switch to Not Member, Tag Member or Untag Member.

Input the VID (1-4094) and check the member row to select the ports which belong to this VLAN group. After these settings are complete click the Create button to submit the data to the switch. Click the Cancel button to abort the actions and go back to the VLAN Config page.

22

Image 23

Contents LINDY No GIGA Smart Switch 24 +User Manual EnglishPage Port Configuration Start to Manage This SwitchConfiguration Functions for the Switch Configurations2.11.1.2 Firmware Update Via BOOTP/TFTP System SetupFirmware Update 2.11.1.1 Firmware Update Via TFTP1 Introduction Main Features „ IP address 1.1 Start to Manage This Switch1.2 Configuration Functions for the Switch 2.1 Port Status 2 Configurationsz 2 Options for ordinary ports Port3 to Port24, copper media only 2.2 Port Configuration9 Fibre -Enable, Copper -Enable - to enable both media z 2 Options for combo ports Port1 and Port2¾ 100Mbps Full - to set the speed 100Mbps in full duplex mode 2.3 About the Copper/Fibre Media Auto-Detection 2.4 Port Statistics Multi Collisions 64 BytePkts 65-127 BytePkts 128-255 BytePkts 256-511 BytePkts 512-1023 BytePkts 1024-1522 BytePkts FCSErrorsAlignErrors SymbolErrors FragmentPkts OverSizePkts UnicastPkts MulticastPkts BroadcastPkts Single CollisionVLAN and 802.1Q VLAN cannot co-exist at the same time 2.5 Port-Based VLAN2.5.1 Add Port-Based VLAN Groups Page Now all ports are set to the members in VLAN group No.1 2.5.2 Delete Port-Based VLAN GroupsPressing the Remove This VLAN button results in the following 2.5.3 Edit Port-Based VLAN Groups 2.6 802.1Q VLAN 2.6.1 Enable/Disable VLAN 2.6.2 802.1Q VLAN Port Configuration 2.6.3 802.1Q VLAN Config The VID entry VID=200 is successfully deleted Finally, click the Apply button to do the changes ¾ SA + DA both SA and DA 2.7 Trunk¾ SA Source MAC Address ¾ DA Destination MAC Address following section will list the related rules for this function 2.7.1 Trunking Rules Page 2.7.2 Get/Refresh the Latest Trunk Settings ¾ Step 2 Choose the member ports up to 8 ports for each trunk group 2.7.3 Enable Trunk¾ Step 3 Click the Apply button to enable trunk settings ¾ Step 1 Choose the Distribution Criterion¾ Step 3 Click the Apply button to modify trunk settings 2.7.4 Modify Trunk Settings¾ Step 1 Click the Not Trunking 2.7.5 Disable Trunk¾ Step 2 Click the Apply button to disable trunk 2.8 Port Mirroring 2.8.1 Get/Refresh the Latest Mirror Settings ¾ Step 2 Choose the Monitored Port to be Port16 2.8.2 Enable Mirror¾ Step 4 Click the Apply button to enable mirroring settings ¾ Step 1 Choose Mirror option to be Mirror All Frames¾ Step 2 Change the Monitored Port to be Port3 2.8.3 Modify Mirror Settings¾ Step 4 Click the Apply button to modify mirroring settings ¾ Step 1 Change Mirror option to be Mirror Outgoing Frames¾ Step 2 Click the Apply button to disable mirroring 2.8.4 Disable Mirror¾ Step 1 Choose Mirror option to be Disable Mirror 2.9 QOS Quality of Service „ Priority/Queue Map 2.9.1 Get/Refresh the Latest QOS Settings„ Weight „ Scheduling Method2.9.2 Enable QOS ¾ Step 1 Change the Scheduling Method to be Strict Priority 2.9.3 Modify QOS Settings¾ Step 3 Click the Apply button to modify QOS settings 2.10.1 Rate Control 2.10 Rate and Storm ControlPage 2.10.2 Storm Control Page 2.11 System Setup 2.11.1 Firmware Update 2.11.1.1 Firmware Update Via TFTP 2.11.1.2 Firmware Update Via BOOTP/TFTP 2.11.2.2 Assign an IP address by DHCP server 2.11.2 DHCP Client2.11.2.1 Assign a fixed IP address 2.11.3 ARL Aging 2.12 User Management 2.13 Reset System „ Login System 2.14 Command Line Interface CLI2.14.1 Hyper Terminal Setup Options 2.14.2 Switch Management Commands In ConsolePress “H”, “h” or “?” to show all management commands in the console „ Get Current Network Settings„ Help Menu „ Get System Information„ User Management „ Configure Network„ Get PVID „ Enable/Disable 802.1Q VLAN„ Get 802.1Q VLAN Enable Setting „ Set PVID„ Reboot System „ Upgrade Firmware Via TFTP or BOOTP/TFTPType “LO” or “lo” to logout of the system „ Reboot System After Write Default„ Logout Type “RD” or “rd” to reset the system to factory settings„ Buffer Memory 3 Specifications„ Standards Compliance „ Interfaces„ Safety „ Power„ Dimensions „ WeightFCC Warning CE Conformity