Lindy 25010 user manual

Page 17

Manual background

Below is the example page when the user sets Port1-12 to the VLAN Group2 after clicking the Create button. Now there is a VLAN group No.2 created with the member Port1-12.

While the group No.2 is created, all the members in group No.1 are removed to operate the VLAN function.

16

Image 17

Contents User Manual GIGA Smart Switch 24 +English LINDY NoPage Configuration Functions for the Switch Start to Manage This SwitchConfigurations Port ConfigurationFirmware Update System Setup2.11.1.1 Firmware Update Via TFTP 2.11.1.2 Firmware Update Via BOOTP/TFTP1 Introduction Main Features „ IP address 1.1 Start to Manage This Switch1.2 Configuration Functions for the Switch 2.1 Port Status 2 Configurations9 Fibre -Enable, Copper -Enable - to enable both media 2.2 Port Configurationz 2 Options for combo ports Port1 and Port2 z 2 Options for ordinary ports Port3 to Port24, copper media only¾ 100Mbps Full - to set the speed 100Mbps in full duplex mode 2.3 About the Copper/Fibre Media Auto-Detection 2.4 Port Statistics AlignErrors SymbolErrors FragmentPkts OverSizePkts 256-511 BytePkts 512-1023 BytePkts 1024-1522 BytePkts FCSErrorsUnicastPkts MulticastPkts BroadcastPkts Single Collision Multi Collisions 64 BytePkts 65-127 BytePkts 128-255 BytePktsVLAN and 802.1Q VLAN cannot co-exist at the same time 2.5 Port-Based VLAN2.5.1 Add Port-Based VLAN Groups Page Now all ports are set to the members in VLAN group No.1 2.5.2 Delete Port-Based VLAN GroupsPressing the Remove This VLAN button results in the following 2.5.3 Edit Port-Based VLAN Groups 2.6 802.1Q VLAN 2.6.1 Enable/Disable VLAN 2.6.2 802.1Q VLAN Port Configuration 2.6.3 802.1Q VLAN Config The VID entry VID=200 is successfully deleted Finally, click the Apply button to do the changes ¾ SA + DA both SA and DA 2.7 Trunk¾ SA Source MAC Address ¾ DA Destination MAC Address following section will list the related rules for this function 2.7.1 Trunking Rules Page 2.7.2 Get/Refresh the Latest Trunk Settings ¾ Step 3 Click the Apply button to enable trunk settings 2.7.3 Enable Trunk¾ Step 1 Choose the Distribution Criterion ¾ Step 2 Choose the member ports up to 8 ports for each trunk group¾ Step 3 Click the Apply button to modify trunk settings 2.7.4 Modify Trunk Settings¾ Step 1 Click the Not Trunking 2.7.5 Disable Trunk¾ Step 2 Click the Apply button to disable trunk 2.8 Port Mirroring 2.8.1 Get/Refresh the Latest Mirror Settings ¾ Step 4 Click the Apply button to enable mirroring settings 2.8.2 Enable Mirror¾ Step 1 Choose Mirror option to be Mirror All Frames ¾ Step 2 Choose the Monitored Port to be Port16¾ Step 4 Click the Apply button to modify mirroring settings 2.8.3 Modify Mirror Settings¾ Step 1 Change Mirror option to be Mirror Outgoing Frames ¾ Step 2 Change the Monitored Port to be Port3¾ Step 2 Click the Apply button to disable mirroring 2.8.4 Disable Mirror¾ Step 1 Choose Mirror option to be Disable Mirror 2.9 QOS Quality of Service „ Weight 2.9.1 Get/Refresh the Latest QOS Settings„ Scheduling Method „ Priority/Queue Map2.9.2 Enable QOS ¾ Step 1 Change the Scheduling Method to be Strict Priority 2.9.3 Modify QOS Settings¾ Step 3 Click the Apply button to modify QOS settings 2.10.1 Rate Control 2.10 Rate and Storm ControlPage 2.10.2 Storm Control Page 2.11 System Setup 2.11.1 Firmware Update 2.11.1.1 Firmware Update Via TFTP 2.11.1.2 Firmware Update Via BOOTP/TFTP 2.11.2.2 Assign an IP address by DHCP server 2.11.2 DHCP Client2.11.2.1 Assign a fixed IP address 2.11.3 ARL Aging 2.12 User Management 2.13 Reset System 2.14.1 Hyper Terminal Setup Options 2.14 Command Line Interface CLI2.14.2 Switch Management Commands In Console „ Login System„ Help Menu „ Get Current Network Settings„ Get System Information Press “H”, “h” or “?” to show all management commands in the console„ User Management „ Configure Network„ Get 802.1Q VLAN Enable Setting „ Enable/Disable 802.1Q VLAN„ Set PVID „ Get PVID„ Reboot System „ Upgrade Firmware Via TFTP or BOOTP/TFTP„ Logout „ Reboot System After Write DefaultType “RD” or “rd” to reset the system to factory settings Type “LO” or “lo” to logout of the system„ Standards Compliance 3 Specifications„ Interfaces „ Buffer Memory„ Dimensions „ Power„ Weight „ SafetyFCC Warning CE Conformity