Lindy 25010 user manual following section will list the related rules for this function

Page 27

Because a trunk port can be aggregated by the member ports with the same configurations in most

functions for each other, there are some rules to limit the configurations of the trunking. The

following section will list the related rules for this function.

26

Image 27

Contents LINDY No GIGA Smart Switch 24 +User Manual EnglishPage Port Configuration Start to Manage This SwitchConfiguration Functions for the Switch Configurations2.11.1.2 Firmware Update Via BOOTP/TFTP System SetupFirmware Update 2.11.1.1 Firmware Update Via TFTP1 Introduction Main Features „ IP address 1.1 Start to Manage This Switch1.2 Configuration Functions for the Switch 2.1 Port Status 2 Configurationsz 2 Options for ordinary ports Port3 to Port24, copper media only 2.2 Port Configuration9 Fibre -Enable, Copper -Enable - to enable both media z 2 Options for combo ports Port1 and Port2¾ 100Mbps Full - to set the speed 100Mbps in full duplex mode 2.3 About the Copper/Fibre Media Auto-Detection 2.4 Port Statistics Multi Collisions 64 BytePkts 65-127 BytePkts 128-255 BytePkts 256-511 BytePkts 512-1023 BytePkts 1024-1522 BytePkts FCSErrorsAlignErrors SymbolErrors FragmentPkts OverSizePkts UnicastPkts MulticastPkts BroadcastPkts Single CollisionVLAN and 802.1Q VLAN cannot co-exist at the same time 2.5 Port-Based VLAN2.5.1 Add Port-Based VLAN Groups Page 2.5.2 Delete Port-Based VLAN Groups Pressing the Remove This VLAN button results in the followingNow all ports are set to the members in VLAN group No.1 2.5.3 Edit Port-Based VLAN Groups 2.6 802.1Q VLAN 2.6.1 Enable/Disable VLAN 2.6.2 802.1Q VLAN Port Configuration 2.6.3 802.1Q VLAN Config The VID entry VID=200 is successfully deleted Finally, click the Apply button to do the changes 2.7 Trunk ¾ SA Source MAC Address ¾ DA Destination MAC Address¾ SA + DA both SA and DA following section will list the related rules for this function 2.7.1 Trunking Rules Page 2.7.2 Get/Refresh the Latest Trunk Settings ¾ Step 2 Choose the member ports up to 8 ports for each trunk group 2.7.3 Enable Trunk¾ Step 3 Click the Apply button to enable trunk settings ¾ Step 1 Choose the Distribution Criterion¾ Step 3 Click the Apply button to modify trunk settings 2.7.4 Modify Trunk Settings2.7.5 Disable Trunk ¾ Step 2 Click the Apply button to disable trunk¾ Step 1 Click the Not Trunking 2.8 Port Mirroring 2.8.1 Get/Refresh the Latest Mirror Settings ¾ Step 2 Choose the Monitored Port to be Port16 2.8.2 Enable Mirror¾ Step 4 Click the Apply button to enable mirroring settings ¾ Step 1 Choose Mirror option to be Mirror All Frames¾ Step 2 Change the Monitored Port to be Port3 2.8.3 Modify Mirror Settings¾ Step 4 Click the Apply button to modify mirroring settings ¾ Step 1 Change Mirror option to be Mirror Outgoing Frames2.8.4 Disable Mirror ¾ Step 1 Choose Mirror option to be Disable Mirror¾ Step 2 Click the Apply button to disable mirroring 2.9 QOS Quality of Service „ Priority/Queue Map 2.9.1 Get/Refresh the Latest QOS Settings„ Weight „ Scheduling Method2.9.2 Enable QOS 2.9.3 Modify QOS Settings ¾ Step 3 Click the Apply button to modify QOS settings¾ Step 1 Change the Scheduling Method to be Strict Priority 2.10.1 Rate Control 2.10 Rate and Storm ControlPage 2.10.2 Storm Control Page 2.11 System Setup 2.11.1 Firmware Update 2.11.1.1 Firmware Update Via TFTP 2.11.1.2 Firmware Update Via BOOTP/TFTP 2.11.2 DHCP Client 2.11.2.1 Assign a fixed IP address2.11.2.2 Assign an IP address by DHCP server 2.11.3 ARL Aging 2.12 User Management 2.13 Reset System „ Login System 2.14 Command Line Interface CLI2.14.1 Hyper Terminal Setup Options 2.14.2 Switch Management Commands In ConsolePress “H”, “h” or “?” to show all management commands in the console „ Get Current Network Settings„ Help Menu „ Get System Information„ User Management „ Configure Network„ Get PVID „ Enable/Disable 802.1Q VLAN„ Get 802.1Q VLAN Enable Setting „ Set PVID„ Reboot System „ Upgrade Firmware Via TFTP or BOOTP/TFTPType “LO” or “lo” to logout of the system „ Reboot System After Write Default„ Logout Type “RD” or “rd” to reset the system to factory settings„ Buffer Memory 3 Specifications„ Standards Compliance „ Interfaces„ Safety „ Power„ Dimensions „ WeightFCC Warning CE Conformity