Lindy 25010 user manual

Contents GIGA Smart Switch 24 + User ManualEnglish LINDY NoPage Start to Manage This Switch Configuration Functions for the SwitchConfigurations Port ConfigurationSystem Setup Firmware Update2.11.1.1 Firmware Update Via TFTP 2.11.1.2 Firmware Update Via BOOTP/TFTP1 Introduction Main Features 1.1 Start to Manage This Switch „ IP address1.2 Configuration Functions for the Switch 2 Configurations 2.1 Port Status2.2 Port Configuration 9 Fibre -Enable, Copper -Enable - to enable both mediaz 2 Options for combo ports Port1 and Port2 z 2 Options for ordinary ports Port3 to Port24, copper media only¾ 100Mbps Full - to set the speed 100Mbps in full duplex mode 2.3 About the Copper/Fibre Media Auto-Detection 2.4 Port Statistics 256-511 BytePkts 512-1023 BytePkts 1024-1522 BytePkts FCSErrors AlignErrors SymbolErrors FragmentPkts OverSizePktsUnicastPkts MulticastPkts BroadcastPkts Single Collision Multi Collisions 64 BytePkts 65-127 BytePkts 128-255 BytePkts2.5 Port-Based VLAN VLAN and 802.1Q VLAN cannot co-exist at the same time2.5.1 Add Port-Based VLAN Groups Page Now all ports are set to the members in VLAN group No.1 2.5.2 Delete Port-Based VLAN GroupsPressing the Remove This VLAN button results in the following 2.5.3 Edit Port-Based VLAN Groups 2.6 802.1Q VLAN 2.6.1 Enable/Disable VLAN 2.6.2 802.1Q VLAN Port Configuration 2.6.3 802.1Q VLAN Config The VID entry VID=200 is successfully deleted Finally, click the Apply button to do the changes ¾ SA + DA both SA and DA 2.7 Trunk¾ SA Source MAC Address ¾ DA Destination MAC Address following section will list the related rules for this function 2.7.1 Trunking Rules Page 2.7.2 Get/Refresh the Latest Trunk Settings 2.7.3 Enable Trunk ¾ Step 3 Click the Apply button to enable trunk settings¾ Step 1 Choose the Distribution Criterion ¾ Step 2 Choose the member ports up to 8 ports for each trunk group2.7.4 Modify Trunk Settings ¾ Step 3 Click the Apply button to modify trunk settings¾ Step 1 Click the Not Trunking 2.7.5 Disable Trunk¾ Step 2 Click the Apply button to disable trunk 2.8 Port Mirroring 2.8.1 Get/Refresh the Latest Mirror Settings 2.8.2 Enable Mirror ¾ Step 4 Click the Apply button to enable mirroring settings¾ Step 1 Choose Mirror option to be Mirror All Frames ¾ Step 2 Choose the Monitored Port to be Port162.8.3 Modify Mirror Settings ¾ Step 4 Click the Apply button to modify mirroring settings¾ Step 1 Change Mirror option to be Mirror Outgoing Frames ¾ Step 2 Change the Monitored Port to be Port3¾ Step 2 Click the Apply button to disable mirroring 2.8.4 Disable Mirror¾ Step 1 Choose Mirror option to be Disable Mirror 2.9 QOS Quality of Service 2.9.1 Get/Refresh the Latest QOS Settings „ Weight„ Scheduling Method „ Priority/Queue Map2.9.2 Enable QOS ¾ Step 1 Change the Scheduling Method to be Strict Priority 2.9.3 Modify QOS Settings¾ Step 3 Click the Apply button to modify QOS settings 2.10 Rate and Storm Control 2.10.1 Rate ControlPage 2.10.2 Storm Control Page 2.11 System Setup 2.11.1 Firmware Update 2.11.1.1 Firmware Update Via TFTP 2.11.1.2 Firmware Update Via BOOTP/TFTP 2.11.2.2 Assign an IP address by DHCP server 2.11.2 DHCP Client2.11.2.1 Assign a fixed IP address 2.11.3 ARL Aging 2.12 User Management 2.13 Reset System 2.14 Command Line Interface CLI 2.14.1 Hyper Terminal Setup Options2.14.2 Switch Management Commands In Console „ Login System„ Get Current Network Settings „ Help Menu„ Get System Information Press “H”, “h” or “?” to show all management commands in the console„ Configure Network „ User Management„ Enable/Disable 802.1Q VLAN „ Get 802.1Q VLAN Enable Setting„ Set PVID „ Get PVID„ Upgrade Firmware Via TFTP or BOOTP/TFTP „ Reboot System„ Reboot System After Write Default „ LogoutType “RD” or “rd” to reset the system to factory settings Type “LO” or “lo” to logout of the system3 Specifications „ Standards Compliance„ Interfaces „ Buffer Memory„ Power „ Dimensions„ Weight „ SafetyCE Conformity FCC Warning