Lindy 25010 user manual Finally, click the Apply button to do the changes

Page 25

Finally, click the Apply button to do the changes.

If you would like to edit the parameters of an 802.1q VLAN, just select a VID to be changed (e.g. VID =300) then click the Apply button to do the modifications: Port 17 and Port18 are selected to be the tag members of this group.

Finally, click the Apply button to do the changes.

24

Image 25

Contents User Manual GIGA Smart Switch 24 +English LINDY NoPage Configuration Functions for the Switch Start to Manage This SwitchConfigurations Port ConfigurationFirmware Update System Setup2.11.1.1 Firmware Update Via TFTP 2.11.1.2 Firmware Update Via BOOTP/TFTP1 Introduction Main Features „ IP address 1.1 Start to Manage This Switch1.2 Configuration Functions for the Switch 2.1 Port Status 2 Configurations9 Fibre -Enable, Copper -Enable - to enable both media 2.2 Port Configurationz 2 Options for combo ports Port1 and Port2 z 2 Options for ordinary ports Port3 to Port24, copper media only¾ 100Mbps Full - to set the speed 100Mbps in full duplex mode 2.3 About the Copper/Fibre Media Auto-Detection 2.4 Port Statistics AlignErrors SymbolErrors FragmentPkts OverSizePkts 256-511 BytePkts 512-1023 BytePkts 1024-1522 BytePkts FCSErrorsUnicastPkts MulticastPkts BroadcastPkts Single Collision Multi Collisions 64 BytePkts 65-127 BytePkts 128-255 BytePktsVLAN and 802.1Q VLAN cannot co-exist at the same time 2.5 Port-Based VLAN2.5.1 Add Port-Based VLAN Groups Page Pressing the Remove This VLAN button results in the following 2.5.2 Delete Port-Based VLAN GroupsNow all ports are set to the members in VLAN group No.1 2.5.3 Edit Port-Based VLAN Groups 2.6 802.1Q VLAN 2.6.1 Enable/Disable VLAN 2.6.2 802.1Q VLAN Port Configuration 2.6.3 802.1Q VLAN Config The VID entry VID=200 is successfully deleted Finally, click the Apply button to do the changes ¾ SA Source MAC Address ¾ DA Destination MAC Address 2.7 Trunk¾ SA + DA both SA and DA following section will list the related rules for this function 2.7.1 Trunking Rules Page 2.7.2 Get/Refresh the Latest Trunk Settings ¾ Step 3 Click the Apply button to enable trunk settings 2.7.3 Enable Trunk¾ Step 1 Choose the Distribution Criterion ¾ Step 2 Choose the member ports up to 8 ports for each trunk group¾ Step 3 Click the Apply button to modify trunk settings 2.7.4 Modify Trunk Settings¾ Step 2 Click the Apply button to disable trunk 2.7.5 Disable Trunk¾ Step 1 Click the Not Trunking 2.8 Port Mirroring 2.8.1 Get/Refresh the Latest Mirror Settings ¾ Step 4 Click the Apply button to enable mirroring settings 2.8.2 Enable Mirror¾ Step 1 Choose Mirror option to be Mirror All Frames ¾ Step 2 Choose the Monitored Port to be Port16¾ Step 4 Click the Apply button to modify mirroring settings 2.8.3 Modify Mirror Settings¾ Step 1 Change Mirror option to be Mirror Outgoing Frames ¾ Step 2 Change the Monitored Port to be Port3¾ Step 1 Choose Mirror option to be Disable Mirror 2.8.4 Disable Mirror¾ Step 2 Click the Apply button to disable mirroring 2.9 QOS Quality of Service „ Weight 2.9.1 Get/Refresh the Latest QOS Settings„ Scheduling Method „ Priority/Queue Map2.9.2 Enable QOS ¾ Step 3 Click the Apply button to modify QOS settings 2.9.3 Modify QOS Settings¾ Step 1 Change the Scheduling Method to be Strict Priority 2.10.1 Rate Control 2.10 Rate and Storm ControlPage 2.10.2 Storm Control Page 2.11 System Setup 2.11.1 Firmware Update 2.11.1.1 Firmware Update Via TFTP 2.11.1.2 Firmware Update Via BOOTP/TFTP 2.11.2.1 Assign a fixed IP address 2.11.2 DHCP Client2.11.2.2 Assign an IP address by DHCP server 2.11.3 ARL Aging 2.12 User Management 2.13 Reset System 2.14.1 Hyper Terminal Setup Options 2.14 Command Line Interface CLI2.14.2 Switch Management Commands In Console „ Login System„ Help Menu „ Get Current Network Settings„ Get System Information Press “H”, “h” or “?” to show all management commands in the console„ User Management „ Configure Network„ Get 802.1Q VLAN Enable Setting „ Enable/Disable 802.1Q VLAN„ Set PVID „ Get PVID„ Reboot System „ Upgrade Firmware Via TFTP or BOOTP/TFTP„ Logout „ Reboot System After Write DefaultType “RD” or “rd” to reset the system to factory settings Type “LO” or “lo” to logout of the system„ Standards Compliance 3 Specifications„ Interfaces „ Buffer Memory„ Dimensions „ Power„ Weight „ SafetyFCC Warning CE Conformity