JVC RX-7022VSL Operating Other Manufacturers’ Video Equipment, Press and hold TV 2 Press TV/DBS

Operating Other Manufacturers’ Video Equipment

By changing the transmittable signals, you can use the remote control supplied for this unit to operate other manufacturers’ equipment.

•Refer also to the manuals supplied for the other products.

•To operate these components with the remote control, first you need to set the manufacturers’ code each for TV, CATV converter, VCR and DVD player.

•After replacing batteries of the remote control, set the manufacturers’ codes again.

To change the transmittable signals for operating a TV

1Press and hold TV .

2Press TV/DBS.

3Enter manufacturer’s codes using buttons 1 – 9, and 0.

4Release TV .

Now, you can perform the following operations on the TV.

TV	: Turn on or off the TV.
TV/VIDEO	: Set the input mode (either TV or VIDEO).
TV VOL +/–	: Adjust the volume.

After pressing TV/DBS, you can perform the following operations on the TV:

CH +/–	: Change the channels.
1 – 9, 0, +10 (100+) : Select a channel.
10	: Function as the ENTER button.

Note:

Refer also to the manual supplied with your TV.

5Try to operate your TV by pressing TV .

When your TV turns on or off, you have entered the correct codes.

If there are more than one code listed for your brand of TV,

try each one until the correct one is entered.

Manufacturers’ codes for TV

Manufacturer	Codes
JVC	00*, 02, 13, 14, 47, 74
AKAI	01, 02
BLAUPUNKT	03, 04
FISHER	01, 05
GRUNDIG	03, 06, 07
HITACHI	08, 09, 10, 49
IRADDIO	02
ITT/NOKIA	11, 12
LOEWE	06, 15, 16
MAGNAVOX	08, 17, 49
METS	50, 51, 52, 53
MITSUBISHI	08, 18, 19, 20
MIVAR	21
NORDMENDE	22, 23
OKANO	15
PANASONIC	24, 25, 26, 27, 76
PHILIPS	15, 17, 28, 75
QUELLE	52, 53, 54, 55, 56, 57, 58,
	59, 60, 61, 62, 63, 64, 65,
	66, 67
RCA/PROSCAN	08, 24, 29, 30, 31, 48
SABA	32, 33, 68, 69, 70
SAMSUNG	06, 08, 16, 34, 35, 49
SANYO	01, 05
SCHNEIDER	02, 15, 36
SHARP	37, 38, 77
SONY	39
TELEFUNKEN	40, 41, 42, 69
THOMSON	71, 72
TOSHIBA	37, 43, 44
ZENITH	45, 46

*“00” is the initial setting.

Manufacturers’ codes are subject to change without notice. If they are changed, this remote control cannot operate the equipment.

To change the transmittable signals for operating a CATV converter or DBS tuner

1Press and hold CATV/DBS .

2Press CATV/DBS CONTROL.

3Enter manufacturer’s codes using buttons 1 – 9, and 0.

4Release CATV/DBS .

Now, you can perform the following operations on the CATV converter or DBS tuner.

CATV/DBS : Turn on or off the CATV converter or DBS tuner.

After pressing CATV/DBS CONTROL, you can perform the following operations on the CATV converter or DBS tuner:

CH +/–	: Change the channels.
1 – 9, 0, +10 (100+) : Select the channels.
10	: Function as the ENTER button.

Note:

Refer also to the manual supplied with your CATV converter or DBS tuner.

37