JVC RX-7022VSL Sound Adjustments, Attenuating the Input Signal, INPUT ANALOG/DIGITAL so, Bass+

Sound Adjustments

Front Panel Remote Control

Display

		RX-7022VAUDIO/VIDEO CONTROL RECEIVER
FM/AM TUNING	FM/AM PRESET	FM MODE

STANDBY	ANALOG	SPK 1 2			BASS BOOST TUNED STEREO	AUTOMUTING SLEEP	BASS+/–
STANDBY/ON	DIGITAL AUTO	L	C	R	PROLOGIC ΙΙ DSP H.PHONE INPUT ATT	VOLUME
				CH-
MEMORY	LINEAR PCM	S.WFR LFE				MASTER VOLUME
	DIGITAL	LS	S	RS

							BASS
SURROUND ON/OFF	INPUT	BASS BOOST					BOOST
	INPUT ATT				ADJUST	SETTING
	ANALOG/DIGITAL
		DVD MULTI	DVD	VCR	TV SOUND/DBS

			SOURCE NAME
SURROUND MODE			CONTROL	SOUND
	SPEAKERS ON/OFF		DOWN UP
1	2	CDTAPE/CDR PHONO	FM/AM
		SOURCE NAME
PHONES
INPUT ATT	BASS BOOST		ADJUST

CONTROL

UP 5/DOWN ∞

A/V CONTROL RECEIVER
CATV/DBS	VCR	TV	AUDIO
DVD	DVD MULTI	CD	FM/AM
TV/DBS	VCR	TAPE/CDR	PHONO
− BASS +		−TREBLE+

SURROUND SURROUND ANALOG/DIGITAL SLEEP

ON/OFF MODE INPUT

BASSBOOST	EFFECT	– CENTER+
	1	2	3
SOUND			MENU
	TEST	– REAR• L+
	4	5	6
			ENTER
DIMMER		– REAR• R+
	7/P	8	9

MUTING–SUBWOOFER+

10 0 +10

RETURN FMMODE 100+

CATV/DBS

CONTROL

+ + +

TV/VIDEO	CH	TV VOL	VOLUME
	−	−	−
+
TUNING	/REW		FF/
−
REC
PAUSE
			CONTROL

RM-SRX7022UREMOTE CONTROL

TREBLE+/–

SUBWOOFER +/–

Once each of following settings has been adjusted, this receiver memorizes the adjustment for each source.

Attenuating the Input Signal	Remote
	NOT

When the input level of the analog source is too high, the sounds will be distorted. If this happens, you need to attenuate the input signal level to prevent the sound distortion.

1 Press and hold INPUT ATT			ANALOG / DIGITAL
			INPUT
(INPUT ANALOG/DIGITAL) so			INPUT ATT
that the INPUT ATT indicator
lights up on the display.
	ANALOG SPK 1
	L C R	INPUT ATT
	S.WFR LFE
	LS S RS
	CH-

•Each time you press and hold the button, the Input Attenuator mode turns on (“INPUT ATT ON”) or off (“INPUT NORMAL”).

Note:

When selecting “DVD MULTI” as the source, this effect does not work.

Adjusting the Front Speakers	Remote
Output Balance
	NOT

If the sounds you hear from the front right and left speakers are unequal, you can adjust the speakers output balance.

Before you start, remember...

There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

1 Press ADJUST repeatedly until		ADJUST SETTIN
“BALANCE” (with the current
setting)* appears on the display.
	SPK 1
	DIGITAL AUTO L C R
	LINEAR PCM S.WFR LFE
	LS S RS
	CH-

*“CNTR (Center)” is the initial setting. If you have already changed the setting, another setting will be shown.

2 Press CONTROL UP	5/DOWN ∞ DOWN UP
	CONTROL
to adjust the balance.

•Pressing CONTROL UP 5 decreases the left channel output from “CNTR” (Center) to “L–21.”

•Pressing CONTROL DOWN ∞ decreases

the right channel output from “CNTR” (Center) to “R–21.”

19