Dukane 28A9017 Control Panel on the Projector, Controls and Features, STAND BY Indicator

Page 11
1STAND BY Indicator

Controls and Features

Control Panel on the Projector

1STAND BY Indicator

Light on : In stand by mode.

Blinking : In cool down mode.

2OPERATE Indicator

Light on : During projection.

9LAMP Indicator

Light on : Indicates the lamp has been used for more than1900 hours.

Blinking : Indicates the lamp has been used for more than 2000 hours.

Please change the lamp. (page 10, 43, 51)

3OPERATE button

When this projector is in standby mode, pressing this but- ton for more than 1 second will turn the projector on and cause the OPERATE indicator to light up. Press it one sec- ond or more again, and the projector goes into the cool down mode and finally into stand by mode. (page 25)

*The OPERATE button will not work within approximately 1 minute of the light-source lamp being turned on. Hence wait about 1 minute before pressing.

4VOLUME ª / · buttons

Use these buttons to adjust the sound volume. (page 27)

5EXIT button

Press this button to display the previous menu. (For exam- ple, from sub menu to main menu). Pressing this button when the main menu is displayed will erase the menu.

(page 35)

6ENTER button

Press this button to show the next menu (For example, from main menu to sub-menu). It is also used when “ENTER” is displayed against an item on the menu screen, or to choose the “Reset” option etc. (page 35)

7HIDE button

Use this button to temporarily halt the audio and video out- put. Press again to resume. (page 29)

8TEMP Indicator

Blinking : Indicates the temperature inside the projector is abnormally high.

pVIDEO button

Use this button to select a device such as a video con- nected to the VIDEO IN terminal (VIDEO or Y/C Input ter- minal) of the projector. (page 25)

qPC button

Use this button to select a device connected to the PC1, PC2 or PC3 terminals. (page 26)

wH-KEYSTONE button

Use this button to remove the horizontal trapezoidal distor- tion of the image projected on the screen. (page 30)

eV-KEYSTONE button

Use this button to remove the vertical trapezoidal distortion of the image projected on the screen. (page 30)

rMENU button

Use this button to enter or exit the menu mode. When the main menu is displayed, pressing this button will cause the menu to disappear. (page 35)

tCURSOR ( /  /  /  ) buttons

These buttons are used in the menu mode to select an item and to set or adjust the value in the sub-menu. (page 35)

yPRESET button

This PRESET button works as a reset button for the [VOLUME] [V-KEYSTONE] [H-KEYSTONE] adjustments done on the control panel and remote control and the [DIGITAL ZOOM] and [SCREEN ] adjustments done on the remote control. (page 28, 30)

When adjusting the volume, keystone or digital zoom (when the setting is displayed) the adjusted value is reset to that which was set when the projector was shipped from the factory. This button does not work for the items in the menu (submenu). (page 35)

About Cool Down mode

Note

After projection, the heated lamp will go through a 90 sec-

Please do not pull out the plug from the power outlet during

onds cool-down period known as the cool down mode. This

cool down mode. Please also do not block the exhaust vents

function is to prevent heat from the heated lamp causing

by standing the projector on its end or laying it on its side.

damage and deformation to the internal components of the

 

projector. It also prevents lamp breakage and shortened

 

lamp life.

 

The Cool down mode is indicated by the blinking STAND

 

BY indicator. During the cool down mode, pressing the

 

OPERATE button will not turn on the projector.

 

After the cool down process is completed, the projector will

 

automatically change to stand by mode.

 

 

 

11

Image 11
Contents Audio Visual Products Model 28A9017Users Manual D-ILA Multimedia ProjectorFCC INFORMATION U.S.A. only SAFETY PRECAUTIONSIMPORTANT INFORMATION NOTICE For USADO NOT allow any unqualified person to install the unit Safety PrecautionDo not cut off the main plug from this equipment POWER CONNECTIONPOWER CONNECTION United Kingdom only How To Replace The FuseViewing conditions Using the screen mode switch functionCleaning the lens About burning-in of the D-ILA deviceAdjustments and Settings Using Menus ContentsAccessories  Optional Accessories4 Foot Lever for front adjustable foot Controls and FeaturesFront Side/ Top Surface/ Left Side 2 AC Power Input Terminalq Connector Panel Controls and FeaturesRear Side/ Right Side/ Bottom Surface Bottom Surface3 PC3 Input Terminal Connector Panel1 PC2 Input Terminal 2 PC1 Input TerminalOPERATE light on Indicator Display on the Control PanelControl Panel on the Projector STAND BY light on4 VOLUME ª / · buttons 1 STAND BY Indicator2 OPERATE Indicator 9 LAMP Indicatore H-KEYSTONE button Remote Control Unitt VOLUME button w PC buttoni PRESET button Controls and Features1 Remote Control’s signal transmitter t VOLUME ª / · buttonBattery Leakage Loading Batteries into the Remote ControlPrecautions for using batteries Battery LifePrecaution for Usage Installing the ProjectorPrecautions for Installation Installation EnvironmentPrecaution for ceiling-mount Installing the Projector against the ScreenInstalling the Projector Mounting the Projector Relationship between projection distance and projection screen size Installing the ProjectorProjection Distance and Screen Size  Screen installationWhen the remote control unit fails to work properly Effective Range and Distance of the Remote Control Unit Using as a wireless remote control unit  Using as a wired Remote Control Computer signals Connecting to Various DevicesSignals that can be input into the projector  Video signalsHorPixels Connecting to Various Devices Allowable input signals SignalRight side of projector Connecting to DevicesConnecting to Various Devices  Connecting to Video DevicesDesktop type DOS/V, etc Desktop type DOS/V, PC-9800 etc  Connecting to ComputersPersonal Computer connector cable supplied connectorConnection for controlling more than one projector  Control from external device Removing the Lens Cap Connecting the Power Cord suppliedWhen using the projector Cautions Against Fire and Electric Shock1 The STAND BY indicator lights up when the power cord is connected Basic OperationsBasic Operation Procedures 1. Power On4. Adjusting the Focus Ring Focus Basic Operations Display using the direct buttons 3. Adjusting the Zoom Ring the screen size for DLA To increase the volume press VOLUME ª 0 Basic OperationsPower Off 5. Adjusting the Sound VolumeEnlarging the Image 1 Magnifying power display “Digital zoom” Display Frequently used Convenient FunctionsPress the FREEZE button Turning Off Image and SoundDisplaying a Still Picture Press the HIDE button once “Vert. Keystone” Display Press V-KEYSTONE / to adjust in the vertical directionPress H-KEYSTONE / to adjust in the horizontal direction Removing the Trapezoidal Distortion of the ImagePress the QUICK ALIGN. Quick Alignment button Using the Quick Alignment functionSelecting the Screen Size  Screen size displayMain menu Adjustments and Settings Using MenusThe Menu Structure Video Input selectionWhen PC input is selected Adjustments and Settings Using MenusSubmenu Adjustments and Settings Using MenusWhen no image signal is inputted PhaseButton Remote control unitmenus “Image adj.”, “Set up” The Menu Operation Buttons6. To EXIT after the adjustment, press the EXIT button The Procedure for Menu Operation4. Press the CURSOR buttons / to select an adjust- ment item 5. Press the CURSOR buttons / to change the setting valueWhen Video input is selected When PC input is selected Adjustment and Setting Using MenusThe Menu Configuration 3 “Set up” menu5 “Decoder” menu When there is no image signal inputted6 “Logo” menu 4 “Position” menu“Page 1” “Signal can not be captured”8 “Capture start” 9 “Options” menu qe “Information” menu When video input is selectedWhen no image signal is inputted 3. Select “Logo” with the CURSOR buttons  /  Editing and Projecting Logo1. Project the images to be included in your logo 2. Press the MENU button4. Select “Horiz. size” with the CURSOR buttons  /  Editing and projecting logo1. Set the menu position as required 3. Select “Vert. move” with the CURSOR buttons  / About lamp replacement The procedure for lamp replacementReplacing the Lamp The light source lamp and its lamp time5. Close the handle, and tighten the screw Replacing the Lamp3. Remove the lamp unit 4. Insert the new lamp unit until it is fully in2. Press the EXIT, HIDE, PRESET buttons on the remote Resetting the lamp timeReplacing the Lamp Caution for reset work4. Reinstalling the filter Cleaning and Replacing the Filter1. Pull out the power cord from the wall outlet 3. Clean the filterWith power on, the TroubleshootingSymptom Power is not supVideo image is ab TroubleshootingVideo image is fuzzyMessage What to do when these messages are displayedCause Contents What to do when these messages are displayed  Action to be taken upon warning indications Warning Indication About warning indicators Please follow the procedures below20% ~ 80% no condensation Specifications Bottom SpecificationsDimensions unit mm  Top RS-232C IN/OUT terminal Signal namePin arrangement  Y/C terminalHeader 1. Communication Specifications2. Command Format  RS-232C external controlPower on 3. External control command tableSERVICE & REPAIR LEGAL INFORMATIONFIVE-YEAR LIMITED WARRANTY 584-5156 Parts & ServiceAudio Visual Products 676-2486