Dukane 28A9017 user manual Basic Operations, Power Off, Adjusting the Sound Volume

Page 27

Basic Operations

Basic Operations

5. Adjusting the Sound Volume

To increase the volume: press VOLUME ª (0 ➞ 50)

	To lower the volume : press VOLUME · (50 ➞ 0)
VOL.	VOLUME

STAND BY

LAMP TEMP OPERATE

PC VIDEO

V-KEYSTONE H-KEYSTONE

VOL.

MENUEXIT

ENTER

OPERATE

5

Projector:	Remote Control
Control panel	Unit
Audio-Vol	12

Screen display

When “Menu display” (☞ page 39) is set to “15sec”, after pressing the VOL- UME button, the sound volume display will appear on the screen for about 15 seconds.

(Press EXIT button to immediately re- move the Audio-vol display.)

Audio-Vol

OPERATE

PC VIDEO

W

V-KEYSTONE H-KEYSTONE SCREEN DIGITAL ZOOM

	S
	FREEZE
VOLUME FOCUS	QUICK ALIGN.
MENU	EXIT

OPERATE

5

Note

•When the sound volume is displayed on the screen, pressing the PRESET button will reset the set value to “0”.

Power Off

1. Press the OPERATE button on the projector (or the OP- ERATE button on the remote control unit ) for 1 second or more.

The OPERATE indicator will disappear, the STAND BY indicator starts to blink, and the projector goes into the cool-down mode.

●The STAND BY indicator will continue blinking for approximately 90 seconds as the temperature of the light source lamp cools (Cool Down Mode).

	ENTER
PRESET	HIDE

OPERATE

	OPERATE
Projector:	Remote Control
Control Panel	Unit

Turn off Turn on

STAND BY

LAMP TEMP OPERATE

Projector: Indicator part

Note

•The OPERATE button will not work for approximately 1 minute from when the light-source lamp is turned on. Wait approxi- mately 1 minute before pressing.

Caution

•Please do not pull out the plug from the power source when the STAND BY indicator is blinking. It will shorten the life of the lamp and cause a malfunction.

27

Image 27

Contents Audio Visual Products Model 28A9017Users Manual D-ILA Multimedia ProjectorFCC INFORMATION U.S.A. only SAFETY PRECAUTIONSIMPORTANT INFORMATION NOTICE For USADO NOT allow any unqualified person to install the unit Safety PrecautionDo not cut off the main plug from this equipment POWER CONNECTIONPOWER CONNECTION United Kingdom only How To Replace The FuseViewing conditions Using the screen mode switch functionCleaning the lens About burning-in of the D-ILA deviceAdjustments and Settings Using Menus ContentsAccessories Optional Accessories4 Foot Lever for front adjustable foot Controls and FeaturesFront Side/ Top Surface/ Left Side 2 AC Power Input Terminalq Connector Panel Controls and FeaturesRear Side/ Right Side/ Bottom Surface Bottom Surface3 PC3 Input Terminal Connector Panel1 PC2 Input Terminal 2 PC1 Input TerminalOPERATE light on Indicator Display on the Control PanelControl Panel on the Projector STAND BY light on4 VOLUME ª / · buttons 1 STAND BY Indicator2 OPERATE Indicator 9 LAMP Indicatore H-KEYSTONE button Remote Control Unitt VOLUME button w PC buttoni PRESET button Controls and Features1 Remote Control’s signal transmitter t VOLUME ª / · buttonBattery Leakage Loading Batteries into the Remote ControlPrecautions for using batteries Battery LifePrecaution for Usage Installing the ProjectorPrecautions for Installation Installation EnvironmentPrecaution for ceiling-mount Installing the Projector against the ScreenInstalling the Projector Mounting the Projector Relationship between projection distance and projection screen size Installing the ProjectorProjection Distance and Screen Size Screen installationWhen the remote control unit fails to work properly Effective Range and Distance of the Remote Control Unit Using as a wireless remote control unit Using as a wired Remote Control Computer signals Connecting to Various DevicesSignals that can be input into the projector Video signalsHorPixels Connecting to Various Devices Allowable input signals SignalRight side of projector Connecting to DevicesConnecting to Various Devices Connecting to Video DevicesDesktop type DOS/V, etc Desktop type DOS/V, PC-9800 etc Connecting to ComputersPersonal Computer connector cable supplied connectorConnection for controlling more than one projector Control from external device Removing the Lens Cap Connecting the Power Cord suppliedWhen using the projector Cautions Against Fire and Electric Shock1 The STAND BY indicator lights up when the power cord is connected Basic OperationsBasic Operation Procedures 1. Power On4. Adjusting the Focus Ring Focus Basic Operations Display using the direct buttons 3. Adjusting the Zoom Ring the screen size for DLA To increase the volume press VOLUME ª 0 Basic OperationsPower Off 5. Adjusting the Sound VolumeEnlarging the Image 1 Magnifying power display “Digital zoom” Display Frequently used Convenient FunctionsPress the FREEZE button Turning Off Image and SoundDisplaying a Still Picture Press the HIDE button once “Vert. Keystone” Display Press V-KEYSTONE / to adjust in the vertical directionPress H-KEYSTONE / to adjust in the horizontal direction Removing the Trapezoidal Distortion of the ImagePress the QUICK ALIGN. Quick Alignment button Using the Quick Alignment functionSelecting the Screen Size Screen size displayMain menu Adjustments and Settings Using MenusThe Menu Structure Video Input selectionWhen PC input is selected Adjustments and Settings Using MenusSubmenu Adjustments and Settings Using MenusWhen no image signal is inputted PhaseButton Remote control unitmenus “Image adj.”, “Set up” The Menu Operation Buttons6. To EXIT after the adjustment, press the EXIT button The Procedure for Menu Operation4. Press the CURSOR buttons / to select an adjust- ment item 5. Press the CURSOR buttons / to change the setting valueWhen Video input is selected When PC input is selected Adjustment and Setting Using MenusThe Menu Configuration 3 “Set up” menu5 “Decoder” menu When there is no image signal inputted6 “Logo” menu 4 “Position” menu“Page 1” “Signal can not be captured”8 “Capture start” 9 “Options” menu qWhen video input is selected When no image signal is inputtede “Information” menu 3. Select “Logo” with the CURSOR buttons / Editing and Projecting Logo1. Project the images to be included in your logo 2. Press the MENU button4. Select “Horiz. size” with the CURSOR buttons / Editing and projecting logo1. Set the menu position as required 3. Select “Vert. move” with the CURSOR buttons / About lamp replacement The procedure for lamp replacementReplacing the Lamp The light source lamp and its lamp time5. Close the handle, and tighten the screw Replacing the Lamp3. Remove the lamp unit 4. Insert the new lamp unit until it is fully in2. Press the EXIT, HIDE, PRESET buttons on the remote Resetting the lamp timeReplacing the Lamp Caution for reset work4. Reinstalling the filter Cleaning and Replacing the Filter1. Pull out the power cord from the wall outlet 3. Clean the filterWith power on, the TroubleshootingSymptom Power is not supVideo image is ab TroubleshootingVideo image is fuzzyWhat to do when these messages are displayed Cause ContentsMessage What to do when these messages are displayed Action to be taken upon warning indications Warning Indication About warning indicators Please follow the procedures below20% ~ 80% no condensation Specifications Bottom SpecificationsDimensions unit mm Top RS-232C IN/OUT terminal Signal namePin arrangement Y/C terminalHeader 1. Communication Specifications2. Command Format RS-232C external controlPower on 3. External control command tableLEGAL INFORMATION FIVE-YEAR LIMITED WARRANTYSERVICE & REPAIR 584-5156 Parts & ServiceAudio Visual Products 676-2486