Dukane 28A9017 Warning Indication, About warning indicators, Please follow the procedures below

Page 51

Warning Indication

Warning Indication

About warning indicators

If something abnormal has occurred in the projector, the warning mode sets in and the type of abnormality will be indicated by a combination of indicators displayed on the control panel as shown in the following table.

The projector will then automatically stop projection and run the cooling fan for about 90 seconds.

No.

Indicator

Warning

LAMP

TEMP

STAND BY

OPERATE

1

Blink

Blink

The light-source lamp does not light up and projection cannot be done.

2

Blink

Blink simultaneously

Blink

The light-source lamp suddenly goes off during projection.

3

Blink

Blink

Circuit operation is abnormal.

4

Blink

Blink alternately

Blink

The light-source lamp is misfitted.

5

Blink

The internal temperature is abnormally high.

6

Blink

Blink

The temperature at the air inlets has risen abnormally high.

7

Blink

Blink

Blink

Blink

The cooling fan has stopped. (Fan locked)

*For details on individually blinking indicators, please see page 43.

Action to be taken upon warning indications

Please follow the procedures below.

For No.1-3

No.1 : Unplug from the main power outlet and restart according to the basic operation procedures.

No.2 : After checking if a shock (such as from knocking) has not ocurred during operation, unplug from the main power outlet and restart according to the basic operation procedures.

No.3 : Unplug from the main power outlet and restart according to the basic operation procedures.

For No.4-7

After the STAND BY indicator lights up, pull out the power cord and check the following items one-by one. No.4 : Ensure that the lamp is correctly set in place. Restart according to the basic operation procedures.

No.5 : Check that nothing is blocking the air inlets, and wait until the inside cools down. Restart according to the basic operation procedures.

No.6 : Check the ambient temperature. If it is normal, leave the projector until it cools down. Restart according to the basic operation procedures.

No.7 : Leave the projector until it cools down. Restart according to the basic operation procedures.

If the same warning indication is observed again despite the instructions above, wait for the cooling fan to stop, check that the STAND BY indicator on, then unplug the power cord and call your dealer for repair.

51

Image 51

Contents Audio Visual Products Model 28A9017Users Manual D-ILA Multimedia ProjectorFCC INFORMATION U.S.A. only SAFETY PRECAUTIONSIMPORTANT INFORMATION NOTICE For USADO NOT allow any unqualified person to install the unit Safety PrecautionDo not cut off the main plug from this equipment POWER CONNECTIONPOWER CONNECTION United Kingdom only How To Replace The FuseViewing conditions Using the screen mode switch functionCleaning the lens About burning-in of the D-ILA deviceAdjustments and Settings Using Menus ContentsAccessories Optional Accessories4 Foot Lever for front adjustable foot Controls and FeaturesFront Side/ Top Surface/ Left Side 2 AC Power Input Terminalq Connector Panel Controls and FeaturesRear Side/ Right Side/ Bottom Surface Bottom Surface3 PC3 Input Terminal Connector Panel1 PC2 Input Terminal 2 PC1 Input TerminalOPERATE light on Indicator Display on the Control PanelControl Panel on the Projector STAND BY light on4 VOLUME ª / · buttons 1 STAND BY Indicator2 OPERATE Indicator 9 LAMP Indicatore H-KEYSTONE button Remote Control Unitt VOLUME button w PC buttoni PRESET button Controls and Features1 Remote Control’s signal transmitter t VOLUME ª / · buttonBattery Leakage Loading Batteries into the Remote ControlPrecautions for using batteries Battery LifePrecaution for Usage Installing the ProjectorPrecautions for Installation Installation EnvironmentPrecaution for ceiling-mount Installing the Projector against the ScreenInstalling the Projector Mounting the Projector Relationship between projection distance and projection screen size Installing the ProjectorProjection Distance and Screen Size Screen installationWhen the remote control unit fails to work properly Effective Range and Distance of the Remote Control Unit Using as a wireless remote control unit Using as a wired Remote Control Computer signals Connecting to Various DevicesSignals that can be input into the projector Video signalsHorPixels Connecting to Various Devices Allowable input signals SignalRight side of projector Connecting to DevicesConnecting to Various Devices Connecting to Video DevicesDesktop type DOS/V, etc Desktop type DOS/V, PC-9800 etc Connecting to ComputersPersonal Computer connector cable supplied connectorConnection for controlling more than one projector Control from external device Removing the Lens Cap Connecting the Power Cord suppliedWhen using the projector Cautions Against Fire and Electric Shock1 The STAND BY indicator lights up when the power cord is connected Basic OperationsBasic Operation Procedures 1. Power On4. Adjusting the Focus Ring Focus Basic Operations Display using the direct buttons 3. Adjusting the Zoom Ring the screen size for DLA To increase the volume press VOLUME ª 0 Basic OperationsPower Off 5. Adjusting the Sound VolumeEnlarging the Image 1 Magnifying power display “Digital zoom” Display Frequently used Convenient FunctionsPress the FREEZE button Turning Off Image and SoundDisplaying a Still Picture Press the HIDE button once “Vert. Keystone” Display Press V-KEYSTONE / to adjust in the vertical directionPress H-KEYSTONE / to adjust in the horizontal direction Removing the Trapezoidal Distortion of the ImagePress the QUICK ALIGN. Quick Alignment button Using the Quick Alignment functionSelecting the Screen Size Screen size displayMain menu Adjustments and Settings Using MenusThe Menu Structure Video Input selectionWhen PC input is selected Adjustments and Settings Using MenusSubmenu Adjustments and Settings Using MenusWhen no image signal is inputted PhaseButton Remote control unitmenus “Image adj.”, “Set up” The Menu Operation Buttons6. To EXIT after the adjustment, press the EXIT button The Procedure for Menu Operation4. Press the CURSOR buttons / to select an adjust- ment item 5. Press the CURSOR buttons / to change the setting valueWhen Video input is selected When PC input is selected Adjustment and Setting Using MenusThe Menu Configuration 3 “Set up” menu5 “Decoder” menu When there is no image signal inputted6 “Logo” menu 4 “Position” menu“Page 1” “Signal can not be captured”8 “Capture start” 9 “Options” menu qWhen video input is selected When no image signal is inputtede “Information” menu 3. Select “Logo” with the CURSOR buttons / Editing and Projecting Logo1. Project the images to be included in your logo 2. Press the MENU button4. Select “Horiz. size” with the CURSOR buttons / Editing and projecting logo1. Set the menu position as required 3. Select “Vert. move” with the CURSOR buttons / About lamp replacement The procedure for lamp replacementReplacing the Lamp The light source lamp and its lamp time5. Close the handle, and tighten the screw Replacing the Lamp3. Remove the lamp unit 4. Insert the new lamp unit until it is fully in2. Press the EXIT, HIDE, PRESET buttons on the remote Resetting the lamp timeReplacing the Lamp Caution for reset work4. Reinstalling the filter Cleaning and Replacing the Filter1. Pull out the power cord from the wall outlet 3. Clean the filterWith power on, the TroubleshootingSymptom Power is not supVideo image is ab TroubleshootingVideo image is fuzzyWhat to do when these messages are displayed Cause ContentsMessage What to do when these messages are displayed Action to be taken upon warning indications Warning Indication About warning indicators Please follow the procedures below20% ~ 80% no condensation Specifications Bottom SpecificationsDimensions unit mm Top RS-232C IN/OUT terminal Signal namePin arrangement Y/C terminalHeader 1. Communication Specifications2. Command Format RS-232C external controlPower on 3. External control command tableLEGAL INFORMATION FIVE-YEAR LIMITED WARRANTYSERVICE & REPAIR 584-5156 Parts & ServiceAudio Visual Products 676-2486