Dukane 8107HWI user manual Perfect FIT Input button, On OFF

Page 47

SETUP menu

Item

Description

Using the ◄/► buttons corrects the horizontal keystone distortion. Shrink the right of the image Shrink the left of the image

KEYSTONE • The adjustable range of this function will vary among inputs. For some input, this function may not work well.

•This function will be unavailable when the Transition Detector is on (76) or the PERFECT FIT (45) is adjusted.

This item allows you to adjust the shape of the projected image in each of the corners and sides.

(1)Choose a corner or side to adjust using the ▲/▼/◄/► buttons and press the ENTER or INPUT button.

(2)Adjust the distortion as below. Use the ▲/▼/◄/► buttons to adjust the position of the corner. Use the ▲/▼ buttons to adjust the distortion of the top or bottom side, after defining the adjusting position with the ◄/► buttons.

Use the ◄/► buttons to adjust the distortion of the left or right side, after defining the adjusting position with the ▲/▼ buttons.

(3)To adjust another corner or side, follow the same procedure from (1) above. To reset the adjustment of all the corners and sides, select RESET with the ▲/▼ buttons and press the ENTER or

PERFECT FIT INPUT button.

•While the distortion is adjusted with the PERFECT FIT function, keystone adjustment feature is unavailable. To correct the keystone distortion, reset the adjustment of all the corners and sides.

•When the amount of correction is increased using the PERFECT FIT function, the Interactive Function may not function properly particularly if the side correction amount is very large.

•The adjustable range of this correction will vary among inputs. For some input, this function may not work well.

•One adjustment position common to the top and bottom sides can be set. Also, another adjustment position common to the left and right sides can be set.

•The distortion of the top and bottom sides can be adjusted only in the same direction, pincushion or barrel. The adjustment for the left and right sides is carried out in the same manner.

•This function will be unavailable when the Transition Detector is on (76).

Using the ▲/▼ buttons turns on/off the AUTO ECO MODE.

ON OFF

AUTO ECO MODE • When ON is selected, the projector will always be set to Eco mode at start-up regardless of the ECO MODE (46) setting. An OSD

message “AUTO ECO MODE” will be displayed for tens of seconds when the projector starts with this function activated.

(continued on next page)

45

Page 46 Page 48
Image 47
Page 46 Page 48
Contents Model 8107HWI Page Trademark acknowledgment About this manualProjector Thank you for purchasing this projectorContents Checking the contents of package FeaturesSmall Part namesProjector HOT1415 Control panel STANDBY/ON buttonButtons Focus +/- buttons Hdmi Computer IN2Zoom button Zoom + button Position button 26 Down button Volume + buttonComputer button MY Button 1 button MY Button 2 button Keystone buttonArrangement Setting upArrangement Connecting with your devices VCR/DVD/Blu-ray Disc Player Computer About Plug-and-Play capabilityConnecting with your devices USB storage Device Monitor Microphone systemHdmi Access point ComputerSecurity slot Connecting to a power supplyUsing the security bar and slot Security bar Anti-theft chain or wireUsing the cable cover Hitachi MAXELL, Part No.LR6 or R6P Remote controlInstalling the batteries About the remote control signalUSB Type B port Changing the frequency of remote control signalUsing as a simple PC mouse & keyboard Hitachi MAXELL, Part No. LR03 Installing the batteryInteractive pen Exchanging the tip of the penSTANDBY/ON button Power on/offTurning on the power Power indicatorTurning off the power Temporarily muting the sound Adjusting the volumeSelecting an input signal OperatingMY Source Press the MY Source / DOC. Camera button onComputer button Video buttonSelecting an aspect ratio Searching an input signalFor a computer signal For an Hdmi TM signalZoom + button Adjusting the projectors elevatorAdjusting the zoom and focus Zoom buttonFocus button Using the automatic adjustment featureFor a video signal and s-video signal For a component video signalKeystone button Adjusting the positionCorrecting the keystone distortions Position buttonMagnify ON/OFF button Using the magnify featureBlank button Temporarily freezing the screenTemporarily blanking the screen Freeze buttonEnter button Using the menu functionESC button Reset button Advanced MenuIndication Meaning Indication in OSD On Screen DisplayZoom DescriptionInteractive AspectMirror Picture ModeECO Mode ResetInteractive menu Gamma Picture menuBrightness ContrastColor Custom MIDLOW CustomActive Iris SharpnessPresentation OFFImage menu For a computer signalFor an Hdmitm signal USB Type B or Hdmi port Signal, the range of this adjustment depends on Over ScanSelected will reset the H Position to the default setting PositionExecute PhaseAuto Adjust SizeVideo NR Input menuTV Film OFF High MID LOWHdmi Range Video FormatHdmi Format Frame Lock Auto Sync on G OFFComputer Resolution No Input is Detected Sync is OUT of Range Invalid Scan Freq Setup menuShift Left MID RightOn OFF Perfect FIT Input buttonNormal Saving Normal ECONormal Hinvert Vinvert Audio Source VolumeAudio menu SpeakerHigh LOW MIC VolumeHdmi Audio MIC LevelEnglish Français Deutsch Español Screen menuMyScreen registration is finished Capturing error has occurred. Please try againMyScreen Message MyScreen LockSource Name Template Channel Description Closed CaptionDisplay ModeComputer IN2 LAN USB Type a Video Video Hdmi USB Type B Direct PowerOption menu USB Type B Auto PowerOFF Mouse USB DisplayLamp Time Cancel OKCancel No Messenger Data appears MY ButtonMode is on, use the / cursor buttons to adjust Active Iris Changes the active iris modePicture Mode Changes the Picture Mode Zoom Turns the D-ZOOM mode on/off. When the D-ZOOMFilter Message ServiceFAN Speed GhostLens Door Close KEY LockLens Door Lock Lens Door OpenControl port Remote Freq1NORMAL 2HIGH Parity Serial SettingsBaud Rate Service Communication TypeTransmission Method Response Limit TimeInformation Factory ResetDhcp SetupNetwork menu Subnet DefaultSetup Gateway IP AddressProjector Name AMX D.D MY ImagePresentation QuitPresenter User Name Section SwitchingMulti PC Guide Security PasswordSecurity menu Enter to the Security menuMyScreen Turning on the MyScreen PasswordTurning off the MyScreen Password If you have forgotten your PIN code PIN LockTurning on the PIN Lock Turning off the PIN LockTurning off the Transition Detector Transition DetectorTurning on the Transition Detector Turning off the MY Text Password MY Text PasswordTurning on the MY Text Password Writing MY TextApplication Presentation toolsInteractive Function System requirementsInteractive Function Connection during use Preliminary preparation Using the penCustomizing the pen Basic pen operationUsing StarBoard Software Supported file format PC-LESS PresentationSupported storage media Supported formatThumbnail menu Selected image Thumbnail images Thumbnail modeEnter Input Setup menu for the selected imageOperating by buttons or keys DownOperating by the menu on the Thumbnail screen PC-LESS Presentation Full Screen Mode Control Projector Software Slideshow modePlay Example of playlist.txt files PlaylistUSB Port USB cable 1 piece USB DisplayHardware and software requirement for computer Floating menu Right-Click menuOptions window Type number 456-8104HW Replacing the lamp MaintenanceReplacing the lamp Lamp warning High Voltage High TemperatureStitched side On next Cleaning and replacing the air filterType number UX37191 Filter set 100 Cleaning and replacing the air filter101 Replacing the internal clock batteryHitachi MAXELL, part number CR2032 or CR2032H 102 Cleaning clothInside of the projector Caring for the cabinet and remote controlMaintenance of the pen sensors horns Maintenance of the pen104 Other careRelated messages TroubleshootingThere is no input signal An improper signal is input106 Internal temperature is risingButton operation is not available Regarding the indicator lamps Lens door is not opened properly It is time to clean the air filterThere is a possibility that the interior portion Has become heatedResetting all settings Mode selected for Hdmi Audio is not suitable Signal cables are not correctly connectedVolume is adjusted to an extremely low level Audio SOURCE/SPEAKER setting is not correctFrame Lock function cannot work on the current Input signal Color settings are not correctly adjustedColor Space setting is not suitable Projector is operating in Eco modeSet to Network Bridge Computer cannot start up in the current hardwareSaving function is working Communication Type for the Control port isIs the system started up in the correct sequence? Is the use of USB cables disabled?Is the power of the projector turned on? Is the USB cable connected correctly?Is the volume from the speaker of the projector too loud? This may be due to poor contact of the batteryHas the battery run out? Are you using more than one pen at the same time?Is the projector inclined? StarBoard Software files may be corrupted, orIs the tip of the pen worn out? Is alignment of the pen position correctly performed?Is the computer image projected within the area Screen? Is the projector correctly installed?Is a part of the image enlarged using the Magnify Function? 117 SpecificationsEnd User License Agreement for the Projector Software
Top Page Image Contents