Dukane 8107HWI user manual Enter to the Security menu, Password, Change

Page 75

SECURITY menu

SECURITY menu

This projector is equipped with security functions. From the SECURITY menu, items shown in the table below can be performed.

To use SECURITY menu: User registration is required before using the security functions.

Enter to the SECURITY menu

1.Press the ► button. The ENTER PASSWORD box will be displayed.

2.Use the ▲/▼/◄/► buttons to enter the registered password. The

factory default password is 4515. This password can be changed (below). Move the cursor to the right side of the ENTER PASSWORD box and press the ► button to display the SECURITY menu.

•It is strongly recommended the factory default password to be changed as soon as possible.

•If an incorrect password is input, the ENTER PASSWORD box

will be displayed again. If incorrect password is input 3 times, the projector will turn off. Afterwards the projector will turn off every time an incorrect password is input.

3. Items shown in the table below can be performed.

If you have forgotten your password

(1). While the ENTER PASSWORD box is displayed, press and hold the RESET button on the remote control for about 3 seconds or press and hold the INPUT button for 3 seconds while pressing the ► button on the projector.

(2). The 10 digit Inquiring Code will be displayed. Contact your dealer with the 10 digit Inquiring Code. Your password will be sent after your user registration information is conﬁrmed.

•If there is no key input for about 55 seconds while the Inquiring Code is displayed, the menu will close. If necessary, repeat the process from (1).

Item		Description

	(1)	Use the ▲/▼ buttons on the SECURITY menu
		to select SECURITY PASSWORD CHANGE
		and press the ► button to display the ENTER
		NEW PASSWORD box.
	(2)	Use the ▲/▼/◄/► buttons to enter the new password.
	(3)	Move the cursor to the right side of the
SECURITY		ENTER NEW PASSWORD box and press the
SECURITY		► button to display the NEW PASSWORD
PASSWORD		AGAIN box, enter the same password again.
CHANGE	(4) Move the cursor to the right side of the NEW
		PASSWORD AGAIN box and press the ►
		button and the NOTE NEW PASSWORD box
		will be displayed for about 30 seconds, please
		make note of the password during this time.
		Pressing the ENTER button on the remote control or ► button on the
		projector will close the NOTE NEW PASSWORD box.
	• Please do not forget your password.

(continued on next page)

73

Image 75

Contents Model 8107HWI Page Trademark acknowledgment About this manualProjector Thank you for purchasing this projectorContents Checking the contents of package FeaturesSmall Part namesProjector HOT1415 Control panel STANDBY/ON buttonButtons Focus +/- buttons Hdmi Computer IN2Zoom button Zoom + button Position button 26 Down button Volume + buttonComputer button MY Button 1 button MY Button 2 button Keystone buttonArrangement Setting upArrangement Connecting with your devices VCR/DVD/Blu-ray Disc Player Computer About Plug-and-Play capabilityConnecting with your devices USB storage Device Monitor Microphone systemHdmi Access point ComputerSecurity slot Connecting to a power supplyUsing the security bar and slot Security bar Anti-theft chain or wireUsing the cable cover Hitachi MAXELL, Part No.LR6 or R6P Remote controlInstalling the batteries About the remote control signalChanging the frequency of remote control signal Using as a simple PC mouse & keyboardUSB Type B port Hitachi MAXELL, Part No. LR03 Installing the batteryInteractive pen Exchanging the tip of the penSTANDBY/ON button Power on/offTurning on the power Power indicatorTurning off the power Temporarily muting the sound Adjusting the volumeSelecting an input signal OperatingMY Source Press the MY Source / DOC. Camera button onComputer button Video buttonSelecting an aspect ratio Searching an input signalFor a computer signal For an Hdmi TM signalZoom + button Adjusting the projectors elevatorAdjusting the zoom and focus Zoom buttonFocus button Using the automatic adjustment featureFor a video signal and s-video signal For a component video signalKeystone button Adjusting the positionCorrecting the keystone distortions Position buttonMagnify ON/OFF button Using the magnify featureBlank button Temporarily freezing the screenTemporarily blanking the screen Freeze buttonEnter button Using the menu functionESC button Reset button Advanced MenuIndication Meaning Indication in OSD On Screen DisplayZoom DescriptionInteractive AspectMirror Picture ModeECO Mode ResetInteractive menu Gamma Picture menuBrightness ContrastColor Custom MIDLOW CustomActive Iris SharpnessPresentation OFFFor a computer signal For an Hdmitm signalImage menu USB Type B or Hdmi port Signal, the range of this adjustment depends on Over ScanSelected will reset the H Position to the default setting PositionExecute PhaseAuto Adjust SizeVideo NR Input menuTV Film OFF High MID LOWVideo Format Hdmi FormatHdmi Range Auto Sync on G OFF ComputerFrame Lock Resolution No Input is Detected Sync is OUT of Range Invalid Scan Freq Setup menuShift Left MID RightOn OFF Perfect FIT Input buttonNormal ECO Normal Hinvert VinvertNormal Saving Audio Source VolumeAudio menu SpeakerHigh LOW MIC VolumeHdmi Audio MIC LevelEnglish Français Deutsch Español Screen menuCapturing error has occurred. Please try again MyScreenMyScreen registration is ﬁnished Message MyScreen LockSource Name Template Channel Description Closed CaptionDisplay ModeDirect Power Option menuComputer IN2 LAN USB Type a Video Video Hdmi USB Type B USB Type B Auto PowerOFF Mouse USB DisplayCancel OK CancelLamp Time No Messenger Data appears MY ButtonMode is on, use the / cursor buttons to adjust Active Iris Changes the active iris modePicture Mode Changes the Picture Mode Zoom Turns the D-ZOOM mode on/off. When the D-ZOOMFilter Message ServiceFAN Speed GhostLens Door Close KEY LockLens Door Lock Lens Door OpenRemote Freq 1NORMAL 2HIGHControl port Parity Serial SettingsBaud Rate Service Communication TypeTransmission Method Response Limit TimeInformation Factory ResetSetup Network menuDhcp Subnet DefaultSetup Gateway IP AddressProjector Name AMX D.D MY ImageQuit PresenterPresentation Section Switching Multi PCUser Name Guide Security PasswordSecurity menu Enter to the Security menuTurning on the MyScreen Password Turning off the MyScreen PasswordMyScreen If you have forgotten your PIN code PIN LockTurning on the PIN Lock Turning off the PIN LockTransition Detector Turning on the Transition DetectorTurning off the Transition Detector MY Text Password Turning on the MY Text PasswordTurning off the MY Text Password Writing MY TextApplication Presentation toolsInteractive Function System requirementsInteractive Function Connection during use Preliminary preparation Using the penCustomizing the pen Basic pen operationUsing StarBoard Software Supported ﬁle format PC-LESS PresentationSupported storage media Supported formatThumbnail menu Selected image Thumbnail images Thumbnail modeEnter Input Setup menu for the selected imageOperating by buttons or keys DownOperating by the menu on the Thumbnail screen PC-LESS Presentation Full Screen Mode Control Projector Software Slideshow modePlay Example of playlist.txt ﬁles PlaylistUSB Display Hardware and software requirement for computerUSB Port USB cable 1 piece Floating menu Right-Click menuOptions window Maintenance Replacing the lampType number 456-8104HW Replacing the lamp Lamp warning High Voltage High TemperatureCleaning and replacing the air ﬁlter Type number UX37191 Filter setStitched side On next 100 Cleaning and replacing the air ﬁlterReplacing the internal clock battery Hitachi MAXELL, part number CR2032 or CR2032H101 102 Cleaning clothInside of the projector Caring for the cabinet and remote controlMaintenance of the pen sensors horns Maintenance of the pen104 Other careRelated messages TroubleshootingThere is no input signal An improper signal is inputInternal temperature is rising Button operation is not available106 Regarding the indicator lamps Lens door is not opened properly It is time to clean the air ﬁlterThere is a possibility that the interior portion Has become heatedResetting all settings Mode selected for Hdmi Audio is not suitable Signal cables are not correctly connectedVolume is adjusted to an extremely low level Audio SOURCE/SPEAKER setting is not correctFrame Lock function cannot work on the current Input signal Color settings are not correctly adjustedColor Space setting is not suitable Projector is operating in Eco modeSet to Network Bridge Computer cannot start up in the current hardwareSaving function is working Communication Type for the Control port isIs the system started up in the correct sequence? Is the use of USB cables disabled?Is the power of the projector turned on? Is the USB cable connected correctly?Is the volume from the speaker of the projector too loud? This may be due to poor contact of the batteryHas the battery run out? Are you using more than one pen at the same time?Is the projector inclined? StarBoard Software ﬁles may be corrupted, orIs the tip of the pen worn out? Is alignment of the pen position correctly performed?Is the projector correctly installed? Is a part of the image enlarged using the Magnify Function?Is the computer image projected within the area Screen? Speciﬁcations End User License Agreement for the Projector Software117